Generated by kicad-footprint-generator · KiCad file format 20260206
STM32G474RET6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
STM32G474RET6 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply for the RTC, backup registers and LSE, with a backup operating voltage of 1.55 V to 3.6 V. |
| 2 | PC13 | bidirectional | 5 V tolerant (FT) GPIO fed through the power switch, which sinks at most 3 mA, so output use is limited to 2 MHz with 30 pF maximum load and it must not source current to LEDs; alternates include TIM1_BKIN, TIM1_CH1N, TIM8_CH4N, with additional functions WKUP2, RTC_TAMP1, RTC_TS and RTC_OUT1. |
| 3 | PC14-OSC32_IN | bidirectional | 5 V tolerant (FT) GPIO on the backup domain that doubles as the 32 kHz oscillator input OSC32_IN, with the same output limits as PC13 (2 MHz, 30 pF, no current sourcing). |
| 4 | PC15-OSC32_OUT | bidirectional | 5 V tolerant (FT) GPIO on the backup domain that doubles as the 32 kHz oscillator output OSC32_OUT, with the same output limits as PC13 (2 MHz, 30 pF, no current sourcing). |
| 5 | PF0-OSC_IN | bidirectional | FT_fa I/O (Fm+ capable) that doubles as the HSE oscillator input OSC_IN, with additional function ADC1_IN10 and alternates I2C2_SDA, SPI2_NSS/I2S2_WS and TIM1_CH3N. |
| 6 | PF1-OSC_OUT | bidirectional | FT_a I/O that doubles as the HSE oscillator output OSC_OUT, with additional functions ADC2_IN10 and COMP3_INM and alternate SPI2_SCK/I2S2_CK. |
| 7 | PG10-NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor (NRST), also usable as FT GPIO PG10 with MCO alternate function. |
| 8 | PC0 | bidirectional | FT_a I/O (5 V tolerant) with additional functions ADC12_IN6 and COMP3_INM and alternates LPTIM1_IN1, TIM1_CH1 and LPUART1_RX. |
| 9 | PC1 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC12_IN7 and COMP3_INP and alternates LPTIM1_OUT, TIM1_CH2, LPUART1_TX, QUADSPI1_BK2_IO0 and SAI1_SD_A. |
| 10 | PC2 | bidirectional | FT_a I/O (5 V tolerant) with additional function ADC12_IN8 and alternates LPTIM1_IN2, TIM1_CH3, COMP3_OUT, TIM20_CH2 and QUADSPI1_BK2_IO1. |
| 11 | PC3 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC12_IN9 and OPAMP5_VINP and alternates LPTIM1_ETR, TIM1_CH4, SAI1_D1, TIM1_BKIN2 and QUADSPI1_BK2_IO2. |
| 12 | PA0 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC12_IN1, COMP1_INM, COMP3_INP, RTC_TAMP2 and WKUP1, and alternates TIM2_CH1, TIM5_CH1, USART2_CTS, COMP1_OUT and TIM8_BKIN. |
| 13 | PA1 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC12_IN2, COMP1_INP, OPAMP1_VINP, OPAMP3_VINP and OPAMP6_VINM, and alternates RTC_REFIN, TIM2_CH2, TIM5_CH2, USART2_RTS_DE and TIM15_CH1N. |
| 14 | PA2 | bidirectional | FT_a I/O (5 V tolerant) with additional functions ADC1_IN3, COMP2_INM, OPAMP1_VOUT and WKUP4/LSCO, and alternates TIM2_CH3, TIM5_CH3, USART2_TX, COMP2_OUT, LPUART1_TX and UCPD1_FRSTX. |
| 15 | VSS | power_in | Ground pin that must always be connected to the external ground within the permitted range. |
| 16 | VDD | power_in | Digital supply pin; standard operating voltage is 1.71 V to 3.6 V and it must always be connected to the external supply. |
| 17 | PA3 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC1_IN4, COMP2_INP, OPAMP1_VINM/OPAMP1_VINP and OPAMP5_VINM, and alternates TIM2_CH4, TIM5_CH4, SAI1_CK1, USART2_RX and LPUART1_RX. |
| 18 | PA4 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC2_IN17, DAC1_OUT1 and COMP1_INM, and alternates TIM3_CH2, SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK and SAI1_FS_B. |
| 19 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC2_IN13, DAC1_OUT2, COMP2_INM and OPAMP2_VINM, and alternates TIM2_CH1, TIM2_ETR, SPI1_SCK and UCPD1_FRSTX. |
| 20 | PA6 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC2_IN3, DAC2_OUT1 and OPAMP2_VOUT, and alternates TIM16_CH1, TIM3_CH1, SPI1_MISO, COMP1_OUT and QUADSPI1_BK1_IO3. |
| 21 | PA7 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC2_IN4, COMP2_INP, OPAMP1_VINP and OPAMP2_VINP, and alternates TIM17_CH1, TIM3_CH2, SPI1_MOSI, TIM1_CH1N, COMP2_OUT and QUADSPI1_BK1_IO2. |
| 22 | PC4 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable) with additional function ADC2_IN5 and alternates TIM1_ETR, I2C2_SCL, USART1_TX and QUADSPI1_BK2_IO3. |
| 23 | PC5 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC2_IN11, OPAMP1_VINM, OPAMP2_VINM and WKUP5, and alternates TIM15_BKIN, SAI1_D3, TIM1_CH4N, USART1_RX and HRTIM1_EEV10. |
| 24 | PB0 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC3_IN12/ADC1_IN15, COMP4_INP, OPAMP2_VINP and OPAMP3_VINP, and alternates TIM3_CH3, TIM1_CH2N, QUADSPI1_BK1_IO1, HRTIM1_FLT5 and UCPD1_FRSTX. |
| 25 | PB1 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC3_IN1/ADC1_IN12, COMP1_INP, OPAMP3_VOUT and OPAMP6_VINM, and alternates TIM3_CH4, TIM1_CH3N, COMP4_OUT, QUADSPI1_BK1_IO0 and LPUART1_RTS_DE. |
| 26 | PB2 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC2_IN12, COMP4_INM and OPAMP3_VINM, and alternates RTC_OUT2, LPTIM1_OUT, TIM5_CH1, TIM20_CH1, I2C3_SMBA, QUADSPI1_BK2_IO1 and HRTIM1_SCIN. |
| 27 | VSSA | power_in | Analog ground pin for the analog domain that supplies the ADCs, DACs, OPAMPs, COMPs and VREFBUF. |
| 28 | VREF+ | power_in | Positive reference voltage input for the ADCs and DACs (with VREFBUF_OUT as an additional function); VREF+ may exceed VDDA by no more than 0.4 V. |
| 29 | VDDA | power_in | Analog supply pin; ADC requires at least 1.62 V, DAC 1 MSPS/15 MSPS and OPAMP at least 1.8 V, VREFBUF used at least 2.4 V, with a maximum of 3.6 V. |
| 30 | PB10 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions COMP5_INM, OPAMP3_VINM and OPAMP4_VINM, and alternates TIM2_CH3, USART3_TX, LPUART1_RX, QUADSPI1_CLK, TIM1_BKIN and HRTIM1_FLT3. |
| 31 | VSS | power_in | Ground pin that must always be connected to the external ground within the permitted range. |
| 32 | VDD | power_in | Digital supply pin; standard operating voltage is 1.71 V to 3.6 V and it must always be connected to the external supply. |
| 33 | PB11 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC12_IN14, COMP6_INP, OPAMP4_VINP and OPAMP6_VOUT, and alternates TIM2_CH4, USART3_RX, LPUART1_TX, QUADSPI1_BK1_NCS and HRTIM1_FLT4. |
| 34 | PB12 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC4_IN3/ADC1_IN11, COMP7_INM, OPAMP4_VOUT and OPAMP6_VINP, and alternates TIM5_ETR, I2C2_SMBA, SPI2_NSS/I2S2_WS, TIM1_BKIN, USART3_CK, FDCAN2_RX and HRTIM1_CHC1. |
| 35 | PB13 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC3_IN5, COMP5_INP, OPAMP3_VINP, OPAMP4_VINP and OPAMP6_VINP, and alternates SPI2_SCK/I2S2_CK, TIM1_CH1N, USART3_CTS, FDCAN2_TX and HRTIM1_CHC2. |
| 36 | PB14 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC4_IN4/ADC1_IN5, COMP7_INP, OPAMP2_VINP and OPAMP5_VINP, and alternates TIM15_CH1, SPI2_MISO, TIM1_CH2N, USART3_RTS_DE, COMP4_OUT and HRTIM1_CHD1. |
| 37 | PB15 | bidirectional | TT_a I/O (3.6 V tolerant) with additional functions ADC4_IN5/ADC2_IN15, COMP6_INM and OPAMP5_VINM, and alternates RTC_REFIN, TIM15_CH2, TIM15_CH1N, TIM1_CH3N, SPI2_MOSI/I2S2_SD and HRTIM1_CHD2. |
| 38 | PC6 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with alternates TIM3_CH1, HRTIM1_EEV10, TIM8_CH1, I2S2_MCK, COMP6_OUT, I2C4_SCL and HRTIM1_CHF1. |
| 39 | PC7 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with alternates TIM3_CH2, HRTIM1_FLT5, TIM8_CH2, I2S3_MCK, COMP5_OUT, I2C4_SDA and HRTIM1_CHF2. |
| 40 | PC8 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with alternates TIM3_CH3, HRTIM1_CHE1, TIM8_CH3, TIM20_CH3, COMP7_OUT and I2C3_SCL. |
| 41 | PC9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with alternates TIM3_CH4, HRTIM1_CHE2, TIM8_CH4, I2SCKIN, TIM8_BKIN2 and I2C3_SDA. |
| 42 | PA8 | bidirectional | FT_a I/O (5 V tolerant) with additional functions ADC5_IN1 and OPAMP5_VOUT, and alternates MCO, I2C3_SCL, I2C2_SDA, TIM1_CH1, USART1_CK, COMP7_OUT, FDCAN3_RX and HRTIM1_CHA1. |
| 43 | PA9 | bidirectional | FT_fda I/O (5 V tolerant, Fm+ capable, USB Type-C dead battery capable) with additional function UCPD1_DBCC1 and alternates I2C3_SMBA, I2C2_SCL, TIM1_CH2, USART1_TX, COMP5_OUT, TIM15_BKIN and HRTIM1_CHA2. |
| 44 | PA10 | bidirectional | FT_fda I/O (5 V tolerant, Fm+ capable, USB Type-C dead battery capable) with additional function UCPD1_DBCC2 and alternates TIM17_BKIN, USB_CRS_SYNC, I2C2_SMBA, SPI2_MISO, TIM1_CH3, USART1_RX and HRTIM1_CHB1. |
| 45 | PA11 | bidirectional | FT_u I/O (5 V tolerant, USB function) with additional function USB_DM and alternates SPI2_MOSI/I2S2_SD, TIM1_CH1N, USART1_CTS, COMP1_OUT, FDCAN1_RX and HRTIM1_CHB2. |
| 46 | PA12 | bidirectional | FT_u I/O (5 V tolerant, USB function) with additional function USB_DP and alternates TIM16_CH1, I2SCKIN, TIM1_CH2N, USART1_RTS_DE, COMP2_OUT, FDCAN1_TX and HRTIM1_FLT1. |
| 47 | VSS | power_in | Ground pin that must always be connected to the external ground within the permitted range. |
| 48 | VDD | power_in | Digital supply pin; standard operating voltage is 1.71 V to 3.6 V and it must always be connected to the external supply. |
| 49 | PA13 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that defaults to the SWDIO-JTMS debug function after reset with its internal pull-up activated, and also has alternates TIM16_CH1N, I2C4_SCL, I2C1_SCL, IR_OUT, USART3_CTS and TIM4_CH3. |
| 50 | PA14 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that defaults to the SWCLK-JTCK debug function after reset with its internal pull-down activated, and also has alternates LPTIM1_OUT, I2C4_SMBA, I2C1_SDA, TIM8_CH2, TIM1_BKIN and USART2_TX. |
| 51 | PA15 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that defaults to the JTDI debug function after reset with its internal pull-up activated, and also has alternates TIM2_CH1, TIM8_CH1, I2C1_SCL, SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_RX, TIM1_BKIN and FDCAN3_TX. |
| 52 | PC10 | bidirectional | FT I/O (5 V tolerant) with alternates TIM8_CH1N, UART4_TX, SPI3_SCK/I2S3_CK, USART3_TX and HRTIM1_FLT6. |
| 53 | PC11 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with alternates HRTIM1_EEV2, TIM8_CH2N, UART4_RX, SPI3_MISO, USART3_RX and I2C3_SDA. |
| 54 | PC12 | bidirectional | FT I/O (5 V tolerant) with alternates TIM5_CH2, HRTIM1_EEV1, TIM8_CH3N, UART5_TX, SPI3_MOSI/I2S3_SD, USART3_CK and UCPD1_FRSTX. |
| 55 | PD2 | bidirectional | FT I/O (5 V tolerant) with alternates TIM3_ETR, TIM8_BKIN and UART5_RX. |
| 56 | PB3 | bidirectional | FT I/O (5 V tolerant) that defaults to the JTDO-TRACESWO debug function after reset, with alternates TIM2_CH2, TIM4_ETR, USB_CRS_SYNC, SPI1_SCK, SPI3_SCK/I2S3_CK, USART2_TX, TIM3_ETR and FDCAN3_RX. |
| 57 | PB4 | bidirectional | FT_c I/O (5 V tolerant, USB Type-C PD capable) that defaults to the JTRST debug function after reset with its internal pull-up activated, with additional function UCPD1_CC2 and alternates TIM16_CH1, TIM3_CH1, SPI1_MISO, SPI3_MISO, USART2_RX and FDCAN3_TX. |
| 58 | PB5 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with alternates TIM16_BKIN, TIM3_CH2, TIM8_CH3N, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI/I2S3_SD, USART2_CK, I2C3_SDA, FDCAN2_RX and TIM17_CH1. |
| 59 | PB6 | bidirectional | FT_c I/O (5 V tolerant, USB Type-C PD capable) with additional function UCPD1_CC1 and alternates TIM16_CH1N, TIM4_CH1, TIM8_CH1, USART1_TX, COMP4_OUT and FDCAN2_TX. |
| 60 | PB7 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with additional function PVD_IN and alternates TIM17_CH1N, TIM4_CH2, I2C4_SDA, I2C1_SDA, TIM8_BKIN, USART1_RX and COMP3_OUT. |
| 61 | PB8-BOOT0 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that is also the BOOT0 pin; it is recommended to set PB8 to a mode other than analog after startup to limit consumption if left unconnected, with alternates TIM16_CH1, TIM4_CH3, I2C1_SCL, USART3_RX and FDCAN1_RX. |
| 62 | PB9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with alternates TIM17_CH1, TIM4_CH4, SAI1_D2, I2C1_SDA, IR_OUT, USART3_TX, COMP2_OUT, FDCAN1_TX and TIM8_CH3. |
| 63 | VSS | power_in | Ground pin that must always be connected to the external ground within the permitted range. |
| 64 | VDD | power_in | Digital supply pin; standard operating voltage is 1.71 V to 3.6 V and it must always be connected to the external supply. |
Key specifications
| Parameter | Value |
|---|---|
| Core | Arm Cortex-M4 |
| Max clock | 170 MHz |
| Flash | 512 kB |
| RAM | 128 kB |
| I/O pins | 52 |
| ADC units | 5 |
| Supply | 1.71 to 3.6 V |
| Temperature | -40 to 85 C |
| ST status | Active |
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | MCU |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage operating range | VDD | 1.71 | 3.6 | V | 23 | ||
| VDDA analog supply voltage operating range | VDDA | 1.62 | 3.6 | V | Minimum VDDA for ADC/DAC/COMP/OPAMP/VREFBUF operation is given in Section 5 | 23 | |
| VBAT supply voltage range | VBAT | 1.55 | 3.6 | V | VBAT powers RTC, 32 kHz oscillator and backup registers when VDD is absent | 24 | |
| Ambient operating temperature range (grade -40 to +85 °C) | -40 | 85 | °C | Junction temperature up to +105 °C; family-level statement, grade for suffix 6 not confirmed | 14 | ||
| Ambient operating temperature range (grade -40 to +125 °C) | -40 | 125 | °C | Junction temperature up to +130 °C; family-level statement, grade for suffix 6 not confirmed | 14 | ||
| Internal 16 MHz RC oscillator accuracy with PLL option | -1 | 1 | % | Features list: internal 16 MHz RC with PLL option | 1 | ||
| Internal 32 kHz RC oscillator accuracy | -5 | 5 | % | Features list: internal 32 kHz RC oscillator | 1 | ||
| I2C Fast-mode-plus current sink | 20 | mA | 4 x I2C Fast mode plus (1 Mbit/s) with 20 mA current sink, features list | 2 | |||
| PC13/PC14/PC15 power switch sink current limit | 3 | mA | Power switch sinks a limited amount of current, Table 12 note 2 | 58 | |||
| PC13/PC14/PC15 GPIO output speed | 2 | MHz | Output mode with maximum load 30 pF, Table 12 note 2 | 58 | |||
| ADC conversion voltage range | 0 | 3.6 | V | 0 to 3.6 V conversion range, features list | 1 |
CAD (KiCad official)
- Symbol:
STM32G474RET6 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32g474ret6-etched.step/stm32g474ret6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32g474ret6.step/stm32g474ret6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (236 pp, sha256
d493fe0ab22e61ff, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).