3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32G473CET6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32G473CET6 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply for the RTC and backup registers, with an operating range of 1.55 V to 3.6 V. |
| 2 | PC13 | bidirectional | 5 V tolerant GPIO supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source current such as an LED drive. |
| 3 | PC14-OSC32_IN | bidirectional | 5 V tolerant GPIO supplied through the power switch (same 3 mA and 2 MHz output limits as PC13), also serving as the 32 kHz oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | 5 V tolerant GPIO supplied through the power switch (same 3 mA and 2 MHz output limits as PC13), also serving as the 32 kHz oscillator output OSC32_OUT. |
| 5 | PF0-OSC_IN | bidirectional | 5 V tolerant Fm+ capable I/O whose additional function is the high-speed crystal oscillator input OSC_IN. |
| 6 | PF1-OSC_OUT | bidirectional | I/O with analog switch function supplied by VDDA, whose additional function is the high-speed crystal oscillator output OSC_OUT. |
| 7 | PG10-NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 8 | PA0 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC12_IN1, COMP1_INM, COMP3_INP, RTC_TAMP2 and WKUP1. |
| 9 | PA1 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC12_IN2 and COMP1_INP. |
| 10 | PA2 | bidirectional | 5 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC1_IN3 and COMP2_INM. |
| 11 | PA3 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC1_IN4 and COMP2_INP. |
| 12 | PA4 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC2_IN17, DAC1_OUT1 and COMP1_INM. |
| 13 | PA5 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC2_IN13 and DAC1_OUT2. |
| 14 | PA6 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC2_IN3, DAC2_OUT1 and OPAMP2_VOUT. |
| 15 | PA7 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC2_IN4, COMP2_INP and OPAMP1_VINP. |
| 16 | PB0 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC3_IN12/ADC1_IN15 and COMP4_INP. |
| 17 | PB1 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC3_IN1/ADC1_IN12 and COMP1_INP. |
| 18 | PB2 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC2_IN12, COMP4_INM and OPAMP3_VINM. |
| 19 | VSSA | power_in | Analog ground for the ADC, DAC, OPAMP, COMP and VREFBUF blocks, to be connected to the ground supply. |
| 20 | VREF+ | power_in | Positive voltage reference input for the ADCs and DACs, also carrying the VREFBUF_OUT function on this package. |
| 21 | VDDA | power_in | Analog supply: 1.62 V minimum for the ADC, 1.8 V minimum for the DAC, OPAMP and COMP, 2.4 V minimum when VREFBUF is used, up to 3.6 V. |
| 22 | PB10 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing COMP5_INM, OPAMP3_VINM and OPAMP4_VINM. |
| 23 | VSS | power_in | Digital ground, to be connected to the ground supply. |
| 24 | VDD | power_in | Digital supply with a standard operating voltage of 1.71 V to 3.6 V. |
| 25 | PB11 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC12_IN14, COMP6_INP and OPAMP4_VINP. |
| 26 | PB12 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC4_IN3/ADC1_IN11, COMP7_INM and OPAMP4_VOUT. |
| 27 | PB13 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC3_IN5, COMP5_INP and OPAMP3_VINP. |
| 28 | PB14 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing ADC4_IN4/ADC1_IN5, COMP7_INP and OPAMP2_VINP. |
| 29 | PB15 | bidirectional | 3.6 V tolerant I/O with analog switch function supplied by VDDA, also providing RTC_REFIN, COMP6_INM and OPAMP5_VINM. |
| 30 | PA8 | bidirectional | 5 V tolerant I/O with analog switch function supplied by VDDA, also providing MCO and ADC5_IN1. |
| 31 | PA9 | bidirectional | 5 V tolerant I/O with Fm+ capability and USB Type-C PD dead-battery capability (UCPD1_DBCC1), also providing ADC5_IN2. |
| 32 | PA10 | bidirectional | 5 V tolerant I/O with Fm+ capability and USB Type-C PD dead-battery capability (UCPD1_DBCC2). |
| 33 | PA11 | bidirectional | I/O with USB function, providing the USB_DM data line. |
| 34 | PA12 | bidirectional | I/O with USB function, providing the USB_DP data line. |
| 35 | VSS | power_in | Digital ground, to be connected to the ground supply. |
| 36 | VDD | power_in | Digital supply with a standard operating voltage of 1.71 V to 3.6 V. |
| 37 | PA13 | bidirectional | Fm+ capable I/O that after reset is configured as the SWDIO-JTMS debug function with its internal pull-up activated. |
| 38 | PA14 | bidirectional | Fm+ capable I/O that after reset is configured as the SWCLK-JTCK debug function with its internal pull-down activated. |
| 39 | PA15 | bidirectional | Fm+ capable I/O that after reset is configured as the JTDI debug function with its internal pull-up activated. |
| 40 | PB3 | bidirectional | 5 V tolerant I/O that after reset is configured as the JTDO-TRACESWO debug function. |
| 41 | PB4 | bidirectional | USB Type-C PD capable I/O that after reset is configured as the JTRST debug function with its internal pull-up activated, also providing UCPD1_CC2. |
| 42 | PB5 | bidirectional | Fm+ capable 5 V tolerant I/O with alternate functions including SPI1_MOSI and I2C1_SMBA. |
| 43 | PB6 | bidirectional | USB Type-C PD capable 5 V tolerant I/O, also providing UCPD1_CC1 and USART1_TX. |
| 44 | PB7 | bidirectional | Fm+ capable 5 V tolerant I/O, also providing the PVD_IN input for the programmable voltage detector. |
| 45 | PB8-BOOT0 | bidirectional | Fm+ capable 5 V tolerant I/O that doubles as the BOOT0 pin; it is recommended to set it out of analog mode after startup to limit consumption if left unconnected. |
| 46 | PB9 | bidirectional | Fm+ capable 5 V tolerant I/O, also providing IR_OUT, USART3_TX and COMP2_OUT. |
| 47 | VSS | power_in | Digital ground, to be connected to the ground supply. |
| 48 | VDD | power_in | Digital supply with a standard operating voltage of 1.71 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 80 | ||
| Analog supply voltage ADC | VDDA | 1.62 | 3.6 | V | ADC | 80 | |
| Analog supply voltage DAC or OPAMP | VDDA | 1.8 | 3.6 | V | DAC 1 MSPS or DAC 15 MSPS or OPAMP | 80 | |
| Analog supply voltage COMP | VDDA | 1.8 | 3.6 | V | COMP used | 80 | |
| Analog supply voltage VREFBUF | VDDA | 2.4 | V | VREFBUF used | 80 | ||
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 80 | ||
| Input voltage FT_c pins | VIN | -0.3 | 5 | V | FT_c | 80 | |
| Ambient temperature suffix 6 maximum power dissipation | TA | -40 | 85 | °C | Suffix 6 version, maximum power dissipation | 80 | |
| Ambient temperature suffix 6 low-power dissipation | TA | -40 | 105 | °C | Suffix 6 version, low-power dissipation | 80 | |
| Junction temperature range suffix 6 | TJ | -40 | 105 | °C | Suffix 6 version | 80 | |
| Internal AHB clock frequency | fHCLK | 0 | 170 | MHz | 80 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 170 | MHz | 80 | ||
| External main supply voltage | VDD-VSS | -0.3 | 4 | V | Including VDD, VDDA and VBAT | 78 | |
| Input voltage on TT_xx pins | VIN | -0.3 | 4 | V | Input voltage on TT_xx pins | 78 | |
| Input voltage on FT_c pins | VIN | -0.3 | 5.5 | V | Input voltage on FT_c pins | 78 | |
| Total current into sum of all VDD power lines | ΣIVDD | 150 | mA | Source | 79 | ||
| Total current out of sum of all VSS ground lines | ΣIVSS | 150 | mA | Sink | 79 | ||
| Maximum current into each VDD power pin | IVDD(PIN) | 100 | mA | Source | 79 | ||
| Maximum current out of each VSS ground pin | IVSS(PIN) | 100 | mA | Sink | 79 | ||
| Output current sunk by any I/O and control pin | IIO(PIN) | 20 | mA | Except FT_f pin | 79 | ||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | Sourced | 79 | ||
| Total output current sunk by sum of all I/Os and control pins | ΣIIO(PIN) | 100 | mA | Sunk | 79 | ||
| Total output current sourced by sum of all I/Os and control pins | ΣIIO(PIN) | 100 | mA | Sourced | 79 | ||
| Injected current on FT_xxx, TT_xx, NRST pins | IINJ(PIN) | -5 | 0 | mA | Printed as -5/0 | 79 | |
| Total injected current sum of all I/Os and control pins | ΣIINJ(PIN) | 25 | mA | Absolute sum of negative injected currents | 79 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 79 | ||
| Maximum junction temperature | TJ | 150 | °C | 79 | |||
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 84 |
| Average temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 84 | |
| Average voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 84 | |
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | μs | VDD rising | 82 | |
| Brown-out reset threshold 0 rising edge | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 82 |
| Brown-out reset threshold 0 falling edge | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 82 |
| Supply current in Standby mode, backup registers retained, RTC disabled | IDD(Standby) | 130 | 350 | nA | VDD 3.0 V, 25°C, no independent watchdog | 106 | |
| Supply current in Run mode, Range 1 Boost, 170 MHz | IDD (Run) | 29.5 | 30 | mA | Range 1 Boost mode, 170 MHz, Flash single bank ART enable, all peripherals disabled, 25°C | 86 |
CAD (KiCad official)
- Symbol:
STM32G473CET6 - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32g473cet6-etched.step/stm32g473cet6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32g473cet6.step/stm32g473cet6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (223 pp, sha256
63caa155ed7b741d, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).