main
Ray
Publish 0.1.0
86fde98
STM32F410CBT6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32F410CBT6 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup power supply for the RTC, external 32 kHz oscillator and backup registers when VDD is not present, 1.65 V to 3.6 V. |
| 2 | PC13 | bidirectional | 5 V tolerant GPIO supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source current such as an LED drive; also RTC_TAMP1, RTC_OUT and RTC_TS. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO supplied through the power switch with the same 3 mA sink limit, also serving as OSC32_IN for the 32 kHz oscillator; 5 V tolerant except in oscillator mode. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO supplied through the power switch with the same 3 mA sink limit, also serving as OSC32_OUT for the 32 kHz oscillator. |
| 5 | PH0 - OSC_IN | bidirectional | GPIO also serving as OSC_IN for the 4-26 MHz crystal oscillator; 5 V tolerant except in oscillator mode. |
| 6 | PH1-OSC_OUT | bidirectional | GPIO also serving as OSC_OUT for the 4-26 MHz crystal oscillator; 5 V tolerant except in oscillator mode. |
| 7 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 8 | VSSA/VREF- | power_in | Analog ground and negative reference voltage for the ADC, reset blocks, RCs and PLL. |
| 9 | VDDA/VREF+ | power_in | Analog supply and positive reference voltage for the ADC, reset blocks, RCs and PLL, 1.7 V to 3.6 V, connected to VDD with decoupling. |
| 10 | PA0 | bidirectional | 5 V tolerant GPIO with ADC1_0 and WKUP1 wakeup, TIM5_CH1, USART2_CTS and EVENTOUT alternate functions. |
| 11 | PA1 | bidirectional | 5 V tolerant GPIO with ADC1_1, TIM5_CH2, USART2_RTS and EVENTOUT alternate functions. |
| 12 | PA2 | bidirectional | 5 V tolerant GPIO with ADC1_2, TIM5_CH3, TIM9_CH1, I2S2_CKIN and USART2_TX alternate functions. |
| 13 | PA3 | bidirectional | 5 V tolerant GPIO with ADC1_3, TIM5_CH4, TIM9_CH2, I2S2_MCK and USART2_RX alternate functions. |
| 14 | PA4 | bidirectional | 5 V tolerant GPIO with ADC1_4, SPI1_NSS/I2S1_WS and USART2_CK alternate functions. |
| 15 | PA5 | bidirectional | Standard 3.3 V I/O (TC, not 5 V tolerant) with ADC1_5, DAC_OUT1 and SPI1_SCK/I2S1_CK alternate functions. |
| 16 | PA6 | bidirectional | 5 V tolerant GPIO with ADC1_6, TIM1_BKIN, SPI1_MISO and I2S2_MCK alternate functions. |
| 17 | PA7 | bidirectional | 5 V tolerant GPIO with ADC1_7, TIM1_CH1N and SPI1_MOSI/I2S1_SD alternate functions. |
| 18 | PB0 | bidirectional | 5 V tolerant GPIO with ADC1_8, TIM1_CH2N and SPI5_SCK/I2S5_CK alternate functions. |
| 19 | PB1 | bidirectional | Standard 3.3 V I/O (TC, not 5 V tolerant) with ADC1_9, TIM1_CH3N and SPI5_NSS/I2S5_WS alternate functions. |
| 20 | PB2 | bidirectional | 5 V tolerant GPIO with LPTIM1_OUT alternate function and BOOT1 additional function. |
| 21 | PB10 | bidirectional | 5 V tolerant GPIO with I2C2_SCL, SPI2_SCK/I2S2_CK, I2S1_MCK and I2C4_SCL alternate functions. |
| 22 | VCAP_1 | power_out | Regulator decoupling pin that must be connected to an external VCAP_1 capacitor as described in Section 6.3.2. |
| 23 | VSS | power_in | Ground pin of the device. |
| 24 | VDD | power_in | Digital supply pin for the I/Os and internal regulator, 1.7 V to 3.6 V. |
| 25 | PB12 | bidirectional | 5 V tolerant GPIO with TIM1_BKIN, TIM5_CH1, I2C2_SMBA, SPI2_NSS/I2S2_WS and EVENTOUT alternate functions. |
| 26 | PB13 | bidirectional | 5 V tolerant GPIO with TIM1_CH1N, I2C4_SMBA and SPI2_SCK/I2S2_CK alternate functions. |
| 27 | PB14 | bidirectional | 5 V tolerant GPIO with TIM1_CH2N, I2C4_SDA and SPI2_MISO alternate functions. |
| 28 | PB15 | bidirectional | 5 V tolerant GPIO with RTC_50Hz, TIM1_CH3N, I2C4_SCL and SPI2_MOSI/I2S2_SD alternate functions. |
| 29 | PA8 | bidirectional | 5 V tolerant GPIO with MCO_1, TIM1_CH1, I2C4_SCL and USART1_CK alternate functions. |
| 30 | PA9 | bidirectional | 5 V tolerant GPIO with TIM1_CH2, USART1_TX and EVENTOUT alternate functions. |
| 31 | PA10 | bidirectional | 5 V tolerant GPIO with TIM1_CH3, SPI5_MOSI/I2S5_SD and USART1_RX alternate functions. |
| 32 | PA11 | bidirectional | 5 V tolerant GPIO with TIM1_CH4, USART1_CTS and USART6_TX alternate functions. |
| 33 | PA12 | bidirectional | 5 V tolerant GPIO with TIM1_ETR, SPI5_MISO, USART1_RTS and USART6_RX alternate functions. |
| 34 | PA13 | bidirectional | 5 V tolerant GPIO with JTMS-SWDIO serial wire debug function. |
| 35 | VSS | power_in | Ground pin of the device. |
| 36 | VDD | power_in | Digital supply pin for the I/Os and internal regulator, 1.7 V to 3.6 V. |
| 37 | PA14 | bidirectional | 5 V tolerant GPIO with JTCK-SWCLK serial wire debug function. |
| 38 | PA15 | bidirectional | 5 V tolerant GPIO with JTDI, SPI1_NSS/I2S1_WS and USART1_TX alternate functions. |
| 39 | PB3 | bidirectional | 5 V tolerant GPIO with JTDO-SWO, I2C4_SDA, SPI1_SCK/I2S1_CK, USART1_RX and I2C2_SDA alternate functions. |
| 40 | PB4 | bidirectional | 5 V tolerant GPIO with JTRST, SPI1_MISO and EVENTOUT alternate functions. |
| 41 | PB5 | bidirectional | 5 V tolerant GPIO with LPTIM1_IN1, I2C1_SMBA and SPI1_MOSI/I2S1_SD alternate functions. |
| 42 | PB6 | bidirectional | 5 V tolerant GPIO with LPTIM1_ETR, I2C1_SCL and USART1_TX alternate functions. |
| 43 | PB7 | bidirectional | 5 V tolerant GPIO with LPTIM1_IN2, I2C1_SDA and USART1_RX alternate functions. |
| 44 | BOOT0 | input | Dedicated BOOT0 pin sampled at startup to select one of three boot options: user Flash, system memory or embedded SRAM. |
| 45 | PB8 | bidirectional | 5 V tolerant GPIO with LPTIM1_OUT, I2C1_SCL and SPI5_MOSI/I2S5_SD alternate functions. |
| 46 | VSS | power_in | Ground pin of the device. |
| 47 | PDR_ON | input | Pin that enables the internal power supply supervisor (POR/PDR) when held high and disables it when set low. |
| 48 | VDD | power_in | Digital supply pin for the I/Os and internal regulator, 1.7 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage | VDD | 1.7 | 3.6 | V | 53 | ||
| Analog operating voltage (ADC limited to 1.2 M samples) | VDDA | 1.7 | 2.4 | V | Must be the same potential as VDD; ADC limited to 1.2 M samples | 53 | |
| Analog operating voltage (ADC limited to 2.4 M samples) | VDDA | 2.4 | 3.6 | V | Must be the same potential as VDD; ADC limited to 2.4 M samples | 53 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 53 | ||
| Internal AHB clock frequency (Power Scale1) | fHCLK | 0 | 100 | MHz | Power Scale1: Regulator ON, VOS[1:0] bits in PWR_CR register = 0x11 | 53 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 50 | MHz | 53 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 100 | MHz | 53 | ||
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 53 | |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.2 | V | VDD ≤ 2 V | 53 | |
| Input voltage on BOOT0 pin | VIN | 0 | 9 | V | 53 | ||
| Maximum allowed package power dissipation LQFP48 at TA = 85 °C (range 6) | PD | 364 | mW | Maximum allowed package power dissipation at TA = 85 °C (range 6) | 54 | ||
| Ambient temperature for range 6 (maximum power dissipation) | TA | -40 | 85 | °C | Ambient temperature for range 6, Maximum power dissipation | 54 | |
| Ambient temperature for range 6 (low power dissipation) | TA | -40 | 105 | °C | Ambient temperature for range 6, Low power dissipation | 54 | |
| Junction temperature range (range 6) | TJ | -40 | 105 | °C | Range 6 | 54 | |
| External main supply voltage (VDD, VDDA, VBAT) | VDD-VSS | -0.3 | 4 | V | Including VDDA, VDD and VBAT | 51 | |
| Input voltage on any other pin | VIN | -0.3 | 4 | V | Input voltage on any other pin, relative to VSS | 51 | |
| Input voltage on FT and TC pins | VIN | -0.3 | V | Min VSS-0.3; max VDD+4.0 V | 51 | ||
| Input voltage for BOOT0 | VIN | 9 | V | Min VSS | 51 | ||
| Maximum current into each VDD_x power line (source) | IVDD | 100 | mA | 52 | |||
| Maximum current out of each VSS_x ground line (sink) | IVSS | -100 | mA | 52 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 52 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 52 | |||
| Total output current sunk by sum of all I/O and control pins | ΣIIO | 120 | mA | 52 | |||
| Total output current sourced by sum of all I/Os and control pins | ΣIIO | -120 | mA | 52 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 52 | ||
| Maximum junction temperature | TJ | 130 | °C | 52 | |||
| Power-on/power-down reset threshold (falling edge) | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 57 |
| Power-on/power-down reset threshold (rising edge) | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 57 |
| Brownout level 1 threshold (falling edge) | VBOR1 | 2.13 | 2.19 | 2.24 | V | Falling edge | 57 |
| Brownout level 1 threshold (rising edge) | VBOR1 | 2.23 | 2.29 | 2.33 | V | Rising edge | 57 |
| Capacitance of external capacitor on VCAP_1 | CEXT | 4.7 | µF | 56 | |||
| ESR of external capacitor on VCAP_1 | ESR | 1 | Ω | 56 | |||
| Oscillator frequency HSE crystal/ceramic resonator | fOSC_IN | 4 | 26 | MHz | 81 | ||
| External user clock source frequency HSE | fHSE_ext | 1 | 50 | MHz | 79 | ||
| Accuracy of the HSI oscillator (user-trimmed) | ACCHSI | -1 | 1 | % | User-trimmed with the RCC_CR register | 83 | |
| Accuracy of the HSI oscillator (factory-calibrated) | ACCHSI | -8 | 5.5 | % | Factory-calibrated, TA = -40 to 125 °C | 83 | |
| Accuracy of the HSI oscillator (factory-calibrated) | ACCHSI | -4 | 4 | % | Factory-calibrated, TA = -10 to 85 °C | 83 | |
| LSI oscillator frequency | fLSI | 17 | 32 | 47 | kHz | VDD = 3 V, TA = -40 to 125 °C | 84 |
| Main PLL input clock | fPLL_IN | 0.95 | 1 | 2.1 | MHz | 84 | |
| PLL VCO output | fVCO_OUT | 100 | 432 | MHz | 84 | ||
| Feedback resistor LSE oscillator | RF | 18.4 | MΩ | 82 |
CAD (KiCad official)
- Symbol:
STM32F410CBT6 - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32f410cbt6-etched.step/stm32f410cbt6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f410cbt6.step/stm32f410cbt6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (143 pp, sha256
71946dd94c3eb53f, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM32F410CBT6
**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32F410CBT6 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup power supply for the RTC, external 32 kHz oscillator and backup registers when VDD is not present, 1.65 V to 3.6 V. |
| 2 | PC13 | bidirectional | 5 V tolerant GPIO supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source current such as an LED drive; also RTC_TAMP1, RTC_OUT and RTC_TS. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO supplied through the power switch with the same 3 mA sink limit, also serving as OSC32_IN for the 32 kHz oscillator; 5 V tolerant except in oscillator mode. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO supplied through the power switch with the same 3 mA sink limit, also serving as OSC32_OUT for the 32 kHz oscillator. |
| 5 | PH0 - OSC_IN | bidirectional | GPIO also serving as OSC_IN for the 4-26 MHz crystal oscillator; 5 V tolerant except in oscillator mode. |
| 6 | PH1-OSC_OUT | bidirectional | GPIO also serving as OSC_OUT for the 4-26 MHz crystal oscillator; 5 V tolerant except in oscillator mode. |
| 7 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 8 | VSSA/VREF- | power_in | Analog ground and negative reference voltage for the ADC, reset blocks, RCs and PLL. |
| 9 | VDDA/VREF+ | power_in | Analog supply and positive reference voltage for the ADC, reset blocks, RCs and PLL, 1.7 V to 3.6 V, connected to VDD with decoupling. |
| 10 | PA0 | bidirectional | 5 V tolerant GPIO with ADC1_0 and WKUP1 wakeup, TIM5_CH1, USART2_CTS and EVENTOUT alternate functions. |
| 11 | PA1 | bidirectional | 5 V tolerant GPIO with ADC1_1, TIM5_CH2, USART2_RTS and EVENTOUT alternate functions. |
| 12 | PA2 | bidirectional | 5 V tolerant GPIO with ADC1_2, TIM5_CH3, TIM9_CH1, I2S2_CKIN and USART2_TX alternate functions. |
| 13 | PA3 | bidirectional | 5 V tolerant GPIO with ADC1_3, TIM5_CH4, TIM9_CH2, I2S2_MCK and USART2_RX alternate functions. |
| 14 | PA4 | bidirectional | 5 V tolerant GPIO with ADC1_4, SPI1_NSS/I2S1_WS and USART2_CK alternate functions. |
| 15 | PA5 | bidirectional | Standard 3.3 V I/O (TC, not 5 V tolerant) with ADC1_5, DAC_OUT1 and SPI1_SCK/I2S1_CK alternate functions. |
| 16 | PA6 | bidirectional | 5 V tolerant GPIO with ADC1_6, TIM1_BKIN, SPI1_MISO and I2S2_MCK alternate functions. |
| 17 | PA7 | bidirectional | 5 V tolerant GPIO with ADC1_7, TIM1_CH1N and SPI1_MOSI/I2S1_SD alternate functions. |
| 18 | PB0 | bidirectional | 5 V tolerant GPIO with ADC1_8, TIM1_CH2N and SPI5_SCK/I2S5_CK alternate functions. |
| 19 | PB1 | bidirectional | Standard 3.3 V I/O (TC, not 5 V tolerant) with ADC1_9, TIM1_CH3N and SPI5_NSS/I2S5_WS alternate functions. |
| 20 | PB2 | bidirectional | 5 V tolerant GPIO with LPTIM1_OUT alternate function and BOOT1 additional function. |
| 21 | PB10 | bidirectional | 5 V tolerant GPIO with I2C2_SCL, SPI2_SCK/I2S2_CK, I2S1_MCK and I2C4_SCL alternate functions. |
| 22 | VCAP_1 | power_out | Regulator decoupling pin that must be connected to an external VCAP_1 capacitor as described in Section 6.3.2. |
| 23 | VSS | power_in | Ground pin of the device. |
| 24 | VDD | power_in | Digital supply pin for the I/Os and internal regulator, 1.7 V to 3.6 V. |
| 25 | PB12 | bidirectional | 5 V tolerant GPIO with TIM1_BKIN, TIM5_CH1, I2C2_SMBA, SPI2_NSS/I2S2_WS and EVENTOUT alternate functions. |
| 26 | PB13 | bidirectional | 5 V tolerant GPIO with TIM1_CH1N, I2C4_SMBA and SPI2_SCK/I2S2_CK alternate functions. |
| 27 | PB14 | bidirectional | 5 V tolerant GPIO with TIM1_CH2N, I2C4_SDA and SPI2_MISO alternate functions. |
| 28 | PB15 | bidirectional | 5 V tolerant GPIO with RTC_50Hz, TIM1_CH3N, I2C4_SCL and SPI2_MOSI/I2S2_SD alternate functions. |
| 29 | PA8 | bidirectional | 5 V tolerant GPIO with MCO_1, TIM1_CH1, I2C4_SCL and USART1_CK alternate functions. |
| 30 | PA9 | bidirectional | 5 V tolerant GPIO with TIM1_CH2, USART1_TX and EVENTOUT alternate functions. |
| 31 | PA10 | bidirectional | 5 V tolerant GPIO with TIM1_CH3, SPI5_MOSI/I2S5_SD and USART1_RX alternate functions. |
| 32 | PA11 | bidirectional | 5 V tolerant GPIO with TIM1_CH4, USART1_CTS and USART6_TX alternate functions. |
| 33 | PA12 | bidirectional | 5 V tolerant GPIO with TIM1_ETR, SPI5_MISO, USART1_RTS and USART6_RX alternate functions. |
| 34 | PA13 | bidirectional | 5 V tolerant GPIO with JTMS-SWDIO serial wire debug function. |
| 35 | VSS | power_in | Ground pin of the device. |
| 36 | VDD | power_in | Digital supply pin for the I/Os and internal regulator, 1.7 V to 3.6 V. |
| 37 | PA14 | bidirectional | 5 V tolerant GPIO with JTCK-SWCLK serial wire debug function. |
| 38 | PA15 | bidirectional | 5 V tolerant GPIO with JTDI, SPI1_NSS/I2S1_WS and USART1_TX alternate functions. |
| 39 | PB3 | bidirectional | 5 V tolerant GPIO with JTDO-SWO, I2C4_SDA, SPI1_SCK/I2S1_CK, USART1_RX and I2C2_SDA alternate functions. |
| 40 | PB4 | bidirectional | 5 V tolerant GPIO with JTRST, SPI1_MISO and EVENTOUT alternate functions. |
| 41 | PB5 | bidirectional | 5 V tolerant GPIO with LPTIM1_IN1, I2C1_SMBA and SPI1_MOSI/I2S1_SD alternate functions. |
| 42 | PB6 | bidirectional | 5 V tolerant GPIO with LPTIM1_ETR, I2C1_SCL and USART1_TX alternate functions. |
| 43 | PB7 | bidirectional | 5 V tolerant GPIO with LPTIM1_IN2, I2C1_SDA and USART1_RX alternate functions. |
| 44 | BOOT0 | input | Dedicated BOOT0 pin sampled at startup to select one of three boot options: user Flash, system memory or embedded SRAM. |
| 45 | PB8 | bidirectional | 5 V tolerant GPIO with LPTIM1_OUT, I2C1_SCL and SPI5_MOSI/I2S5_SD alternate functions. |
| 46 | VSS | power_in | Ground pin of the device. |
| 47 | PDR_ON | input | Pin that enables the internal power supply supervisor (POR/PDR) when held high and disables it when set low. |
| 48 | VDD | power_in | Digital supply pin for the I/Os and internal regulator, 1.7 V to 3.6 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage | VDD | 1.7 | | 3.6 | V | | 53 |
| Analog operating voltage (ADC limited to 1.2 M samples) | VDDA | 1.7 | | 2.4 | V | Must be the same potential as VDD; ADC limited to 1.2 M samples | 53 |
| Analog operating voltage (ADC limited to 2.4 M samples) | VDDA | 2.4 | | 3.6 | V | Must be the same potential as VDD; ADC limited to 2.4 M samples | 53 |
| Backup operating voltage | VBAT | 1.65 | | 3.6 | V | | 53 |
| Internal AHB clock frequency (Power Scale1) | fHCLK | 0 | | 100 | MHz | Power Scale1: Regulator ON, VOS[1:0] bits in PWR_CR register = 0x11 | 53 |
| Internal APB1 clock frequency | fPCLK1 | 0 | | 50 | MHz | | 53 |
| Internal APB2 clock frequency | fPCLK2 | 0 | | 100 | MHz | | 53 |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 53 |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | | 5.2 | V | VDD ≤ 2 V | 53 |
| Input voltage on BOOT0 pin | VIN | 0 | | 9 | V | | 53 |
| Maximum allowed package power dissipation LQFP48 at TA = 85 °C (range 6) | PD | | | 364 | mW | Maximum allowed package power dissipation at TA = 85 °C (range 6) | 54 |
| Ambient temperature for range 6 (maximum power dissipation) | TA | -40 | | 85 | °C | Ambient temperature for range 6, Maximum power dissipation | 54 |
| Ambient temperature for range 6 (low power dissipation) | TA | -40 | | 105 | °C | Ambient temperature for range 6, Low power dissipation | 54 |
| Junction temperature range (range 6) | TJ | -40 | | 105 | °C | Range 6 | 54 |
| External main supply voltage (VDD, VDDA, VBAT) | VDD-VSS | -0.3 | | 4 | V | Including VDDA, VDD and VBAT | 51 |
| Input voltage on any other pin | VIN | -0.3 | | 4 | V | Input voltage on any other pin, relative to VSS | 51 |
| Input voltage on FT and TC pins | VIN | -0.3 | | | V | Min VSS-0.3; max VDD+4.0 V | 51 |
| Input voltage for BOOT0 | VIN | | | 9 | V | Min VSS | 51 |
| Maximum current into each VDD_x power line (source) | IVDD | | | 100 | mA | | 52 |
| Maximum current out of each VSS_x ground line (sink) | IVSS | -100 | | | mA | | 52 |
| Output current sunk by any I/O and control pin | IIO | | | 25 | mA | | 52 |
| Output current sourced by any I/O and control pin | IIO | -25 | | | mA | | 52 |
| Total output current sunk by sum of all I/O and control pins | ΣIIO | | | 120 | mA | | 52 |
| Total output current sourced by sum of all I/Os and control pins | ΣIIO | -120 | | | mA | | 52 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 52 |
| Maximum junction temperature | TJ | | | 130 | °C | | 52 |
| Power-on/power-down reset threshold (falling edge) | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 57 |
| Power-on/power-down reset threshold (rising edge) | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 57 |
| Brownout level 1 threshold (falling edge) | VBOR1 | 2.13 | 2.19 | 2.24 | V | Falling edge | 57 |
| Brownout level 1 threshold (rising edge) | VBOR1 | 2.23 | 2.29 | 2.33 | V | Rising edge | 57 |
| Capacitance of external capacitor on VCAP_1 | CEXT | | 4.7 | | µF | | 56 |
| ESR of external capacitor on VCAP_1 | ESR | | | 1 | Ω | | 56 |
| Oscillator frequency HSE crystal/ceramic resonator | fOSC_IN | 4 | | 26 | MHz | | 81 |
| External user clock source frequency HSE | fHSE_ext | 1 | | 50 | MHz | | 79 |
| Accuracy of the HSI oscillator (user-trimmed) | ACCHSI | -1 | | 1 | % | User-trimmed with the RCC_CR register | 83 |
| Accuracy of the HSI oscillator (factory-calibrated) | ACCHSI | -8 | | 5.5 | % | Factory-calibrated, TA = -40 to 125 °C | 83 |
| Accuracy of the HSI oscillator (factory-calibrated) | ACCHSI | -4 | | 4 | % | Factory-calibrated, TA = -10 to 85 °C | 83 |
| LSI oscillator frequency | fLSI | 17 | 32 | 47 | kHz | VDD = 3 V, TA = -40 to 125 °C | 84 |
| Main PLL input clock | fPLL_IN | 0.95 | 1 | 2.1 | MHz | | 84 |
| PLL VCO output | fVCO_OUT | 100 | | 432 | MHz | | 84 |
| Feedback resistor LSE oscillator | RF | | 18.4 | | MΩ | | 82 |
## CAD (KiCad official)
- Symbol: `STM32F410CBT6`
- Footprint: `Package_QFP:LQFP-48_7x7mm_P0.5mm`
- 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files: `stm32f410cbt6-etched.step` / `stm32f410cbt6-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32f410cbt6.step` / `stm32f410cbt6.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/stm32f410cbt6.pdf) (143 pp, sha256 `71946dd94c3eb53f`, retrieved 2026-11-06, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm32f410cbt6-datasheet.pdf)