Generated by kicad-footprint-generator · KiCad file format 20260206
STM32F401CBU7
STMicroelectronics · ST Microelectronics · UFQFPN-48(7x7)
STM32F401CBU7 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Power supply for the RTC and backup domain, with the datasheet quoting VBAT supply for RTC at 1 µA @25 °C. |
| 2 | PC13 | bidirectional | 5 V tolerant I/O supplied through the power switch, which sinks only 3 mA, so output use is limited to 2 MHz max with 30 pF max load and it must not source current such as driving an LED; alternate functions EVENTOUT, RTC_TAMP1, RTC_OUT, RTC_TS. |
| 3 | PC14-OSC32_IN (PC14) | bidirectional | 5 V tolerant I/O (except in oscillator mode) with the same power-switch limit of 3 mA as PC13, and OSC32_IN is the 32.768 kHz LSE oscillator input function. |
| 4 | PC15-OSC32_OUT (PC15) | bidirectional | 5 V tolerant I/O (except in oscillator mode) with the same power-switch limit of 3 mA as PC13, and OSC32_OUT is the LSE oscillator output function. |
| 5 | PH0-OSC_IN | bidirectional | 5 V tolerant I/O (except in oscillator mode) whose additional function OSC_IN is the 4-26 MHz HSE oscillator input. |
| 6 | PH1-OSC_OUT (PH1) | bidirectional | 5 V tolerant I/O (except in oscillator mode) whose additional function OSC_OUT is the 4-26 MHz HSE oscillator output. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 8 | VSSA/VREF- | power_in | Analog ground pin shared with the ADC negative reference VREF-. |
| 9 | VDDA/VREF+ | power_in | Analog supply pin shared with the ADC positive reference VREF+. |
| 10 | PA0 | bidirectional | 5 V tolerant I/O with ADC1_IN0 and WKUP wakeup; alternate functions USART2_CTS, TIM2_CH1/TIM2_ETR, TIM5_CH1, EVENTOUT. |
| 11 | PA1 | bidirectional | 5 V tolerant I/O with ADC1_IN1; alternate functions USART2_RTS, TIM2_CH2, TIM5_CH2, EVENTOUT. |
| 12 | PA2 | bidirectional | 5 V tolerant I/O with ADC1_IN2; alternate functions USART2_TX, TIM2_CH3, TIM5_CH3, TIM9_CH1, EVENTOUT. |
| 13 | PA3 | bidirectional | 5 V tolerant I/O with ADC1_IN3; alternate functions USART2_RX, TIM2_CH4, TIM5_CH4, TIM9_CH2, EVENTOUT. |
| 14 | PA4 | bidirectional | 5 V tolerant I/O with ADC1_IN4; alternate functions SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK, EVENTOUT. |
| 15 | PA5 | bidirectional | 5 V tolerant I/O with ADC1_IN5; alternate functions SPI1_SCK, TIM2_CH1/TIM2_ETR, EVENTOUT. |
| 16 | PA6 | bidirectional | 5 V tolerant I/O with ADC1_IN6; alternate functions SPI1_MISO, TIM1_BKIN, TIM3_CH1, EVENTOUT. |
| 17 | PA7 | bidirectional | 5 V tolerant I/O with ADC1_IN7; alternate functions SPI1_MOSI, TIM1_CH1N, TIM3_CH2, EVENTOUT. |
| 18 | PB0 | bidirectional | 5 V tolerant I/O with ADC1_IN8; alternate functions TIM1_CH2N, TIM3_CH3, EVENTOUT. |
| 19 | PB1 | bidirectional | 5 V tolerant I/O with ADC1_IN9; alternate functions TIM1_CH3N, TIM3_CH4, EVENTOUT. |
| 20 | PB2 | bidirectional | 5 V tolerant I/O whose additional function is BOOT1; alternate function EVENTOUT. |
| 21 | PB10 | bidirectional | 5 V tolerant I/O; alternate functions SPI2_SCK/I2S2_CK, I2C2_SCL, TIM2_CH3, EVENTOUT. |
| 22 | VCAP_1 | power_in | Connection for the external VCAP_1 capacitor of the internal voltage regulator (see section 6.3.2). |
| 23 | VSS | power_in | Ground pin for the digital supply. |
| 24 | VDD | power_in | Digital supply pin; application supply range is 1.7 V to 3.6 V. |
| 25 | PB12 | bidirectional | 5 V tolerant I/O; alternate functions SPI2_NSS/I2S2_WS, I2C2_SMBA, TIM1_BKIN, EVENTOUT. |
| 26 | PB13 | bidirectional | 5 V tolerant I/O; alternate functions SPI2_SCK/I2S2_CK, TIM1_CH1N, EVENTOUT. |
| 27 | PB14 | bidirectional | 5 V tolerant I/O; alternate functions SPI2_MISO, I2S2ext_SD, TIM1_CH2N, EVENTOUT. |
| 28 | PB15 | bidirectional | 5 V tolerant I/O with additional function RTC_REFIN; alternate functions SPI2_MOSI/I2S2_SD, TIM1_CH3N, EVENTOUT. |
| 29 | PA8 | bidirectional | 5 V tolerant I/O with additional function MCO_1; alternate functions I2C3_SCL, USART1_CK, TIM1_CH1, OTG_FS_SOF, EVENTOUT. |
| 30 | PA9 | bidirectional | 5 V tolerant I/O with additional function OTG_FS_VBUS; alternate functions I2C3_SMBA, USART1_TX, TIM1_CH2, EVENTOUT. |
| 31 | PA10 | bidirectional | 5 V tolerant I/O with additional function OTG_FS_ID; alternate functions USART1_RX, TIM1_CH3, EVENTOUT. |
| 32 | PA11 | bidirectional | 5 V tolerant I/O with additional function OTG_FS_DM; alternate functions USART1_CTS, USART6_TX, TIM1_CH4, EVENTOUT. |
| 33 | PA12 | bidirectional | 5 V tolerant I/O with additional function OTG_FS_DP; alternate functions USART1_RTS, USART6_RX, TIM1_ETR, EVENTOUT. |
| 34 | PA13 (JTMS-SWDIO) | bidirectional | 5 V tolerant I/O whose debug function is JTMS-SWDIO; alternate function EVENTOUT. |
| 35 | VSS | power_in | Ground pin for the digital supply. |
| 36 | VDD | power_in | Digital supply pin; application supply range is 1.7 V to 3.6 V. |
| 37 | PA14 (JTCK-SWCLK) | bidirectional | 5 V tolerant I/O whose debug function is JTCK-SWCLK; alternate function EVENTOUT. |
| 38 | PA15 (JTDI) | bidirectional | 5 V tolerant I/O whose debug function is JTDI; alternate functions SPI1_NSS, SPI3_NSS/I2S3_WS, TIM2_CH1/TIM2_ETR, EVENTOUT. |
| 39 | PB3 (JTDO-SWO) | bidirectional | 5 V tolerant I/O whose debug function is JTDO-SWO; alternate functions SPI1_SCK, SPI3_SCK/I2S3_CK, I2C2_SDA, TIM2_CH2, EVENTOUT. |
| 40 | PB4 (NJTRST) | bidirectional | 5 V tolerant I/O whose debug function is NJTRST; alternate functions SPI1_MISO, SPI3_MISO, I2S3ext_SD, I2C3_SDA, TIM3_CH1, EVENTOUT. |
| 41 | PB5 | bidirectional | 5 V tolerant I/O; alternate functions SPI1_MOSI, SPI3_MOSI/I2S3_SD, I2C1_SMBA, TIM3_CH2, EVENTOUT. |
| 42 | PB6 | bidirectional | 5 V tolerant I/O; alternate functions I2C1_SCL, USART1_TX, TIM4_CH1, EVENTOUT. |
| 43 | PB7 | bidirectional | 5 V tolerant I/O; alternate functions I2C1_SDA, USART1_RX, TIM4_CH2, EVENTOUT. |
| 44 | BOOT0 | input | Dedicated BOOT0 pin used for boot selection, with additional function VPP. |
| 45 | PB8 | bidirectional | 5 V tolerant I/O; alternate functions I2C1_SCL, TIM4_CH3, TIM10_CH1, SDIO_D4, EVENTOUT. |
| 46 | PB9 | bidirectional | 5 V tolerant I/O; alternate functions SPI2_NSS/I2S2_WS, I2C1_SDA, TIM4_CH4, TIM11_CH1, SDIO_D5, EVENTOUT. |
| 47 | VSS | power_in | Ground pin for the digital supply. |
| 48 | VDD | power_in | Digital supply pin; application supply range is 1.7 V to 3.6 V. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA, VDD and VBAT) | VDD-VSS | -0.3 | 4 | V | 57 | ||
| Input voltage on any other pin | VIN | 4 | V | 57 | |||
| Input voltage for BOOT0 | VIN | 9 | V | 57 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 57 | |||
| Variations between all the different ground pins including VREF- | /VSSx −VSS/ | 50 | mV | 57 | |||
| Total current into sum of all VDD_x power lines (source) | ΣIVDD | 160 | mA | 58 | |||
| Total current out of sum of all VSS_x ground lines (sink) | ΣIVSS | -160 | mA | 58 | |||
| Maximum current into each VDD_x power line (source) | IVDD | 100 | mA | 58 | |||
| Maximum current out of each VSS_x ground line (sink) | IVSS | -100 | mA | 58 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 58 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 58 | |||
| Total output current sunk by sum of all I/O and control pins | ΣIIO | 120 | mA | 58 | |||
| Total output current sourced by sum of all I/Os and control pins | ΣIIO | -120 | mA | 58 | |||
| Injected current on FT pins | IINJ(PIN) | -5 | 0 | mA | 58 | ||
| Injected current on NRST and B pins | IINJ(PIN) | -5 | 0 | mA | 58 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 58 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 58 | ||
| Maximum junction temperature | TJ | 130 | °C | 58 | |||
| Internal AHB clock frequency | fHCLK | 0 | 60 | MHz | Power Scale3: Regulator ON, VOS[1:0] bits in PWR_CR register = 0x01 | 59 | |
| Internal AHB clock frequency | fHCLK | 0 | 84 | MHz | Power Scale2: Regulator ON, VOS[1:0] bits in PWR_CR register = 0x10 | 59 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 42 | MHz | 59 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 84 | MHz | 59 | ||
| Standard operating voltage | VDD | 1.7 | 3.6 | V | 59 | ||
| Analog operating voltage (ADC limited to 1.2 M samples), must be the same potential as VDD | VDDA | 1.7 | 2.4 | V | ADC limited to 1.2 M samples | 59 | |
| Analog operating voltage (ADC limited to 2.4 M samples) | VDDA | 2.4 | 3.6 | V | ADC limited to 2.4 M samples | 59 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 59 | ||
| 1.2 V internal voltage on VCAP_1/VCAP_2 pins (regulator ON) | V12 | 1.08 | 1.14 | 1.2 | V | VOS[1:0] bits in PWR_CR register = 0x01; max frequency 60 MHz | 59 |
| 1.2 V internal voltage on VCAP_1/VCAP_2 pins (regulator ON) | V12 | 1.2 | 1.26 | 1.32 | V | VOS[1:0] bits in PWR_CR register = 0x10; max frequency 84 MHz | 59 |
| Input voltage on RST and FT pins | VIN | -0.3 | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 59 | |
| Input voltage on RST and FT pins | VIN | -0.3 | 5.2 | V | VDD ≤ 2 V | 59 | |
| Input voltage on BOOT0 pin | VIN | 0 | 9 | V | 59 | ||
| Power dissipation at TA = 85 °C (range 6) or 105 °C (range 7), UFQFPN48 | PD | 625 | mW | TA = 85 °C (range 6) or 105 °C (range 7) | 59 | ||
| Ambient temperature for range 7, maximum power dissipation | TA | -40 | 105 | °C | Range 7, maximum power dissipation | 60 | |
| Ambient temperature for range 7, low power dissipation | TA | -40 | 125 | °C | Range 7, low power dissipation | 60 | |
| Junction temperature range | TJ | -40 | 125 | °C | Range 7 | 60 | |
| ESR of external capacitor with available VCAP_1 and VCAP_2 pins | ESR | 2 | Ω | with available VCAP_1 and VCAP_2 pins | 61 | ||
| VDD rise time rate (power-up, regulator ON) | tVDD | 20 | µs/V | 61 | |||
| VDD fall time rate (power-down, regulator ON) | tVDD | 20 | µs/V | 61 | |||
| Power-on/power-down reset threshold | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 62 |
| Power-on/power-down reset threshold | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 62 |
| Brownout level 1 threshold | VBOR1 | 2.13 | 2.19 | 2.24 | V | Falling edge | 62 |
| Brownout level 1 threshold | VBOR1 | 2.23 | 2.29 | 2.33 | V | Rising edge | 62 |
| POR reset timing | TRSTTEMPO | 0.5 | 1.5 | 3 | ms | 63 | |
| InRush current on voltage regulator power-on (POR or wakeup from Standby) | IRUSH | 160 | 200 | mA | 63 | ||
| InRush energy on voltage regulator power-on (POR or wakeup from Standby) | ERUSH | 5.4 | µC | VDD = 1.7 V, TA = 125 °C, IRUSH = 171 mA for 31 µs | 63 | ||
| Accuracy of the HSI oscillator | ACCHSI | -1 | 1 | % | Factory calibrated, TA = 25 °C | 79 | |
| Accuracy of the HSI oscillator | ACCHSI | -4 | 4 | % | Factory calibrated, TA = -10 to 85 °C | 79 | |
| Accuracy of the HSI oscillator | ACCHSI | -8 | 4.5 | % | Factory calibrated, TA = -40 to 105 °C | 79 | |
| Accuracy of the HSI oscillator | ACCHSI | -8 | 5.5 | % | Factory calibrated, TA = -40 to 125 °C | 79 | |
| LSI oscillator frequency | fLSI | 17 | 32 | 47 | kHz | VDD = 3 V, TA = -40 to 125 °C | 80 |
| Oscillator frequency (HSE 4-26 MHz) | fOSC_IN | 4 | 26 | MHz | 77 | ||
| PLL input clock | fPLL_IN | 0.95 | 1 | 2.1 | MHz | 81 | |
| PLL multiplier output clock | fPLL_OUT | 24 | 84 | MHz | 81 | ||
| PLL VCO output | fVCO_OUT | 192 | 432 | MHz | 81 | ||
| Endurance | NEND | 10 | Kcycles | TA = -40 to +105 °C (temp. range 7) | 86 | ||
| Low power regulator usage, Flash in Stop mode, all oscillators OFF, no independent watchdog (VDD=3.3 V) | IDD_STOP | 42 | 65 | µA | TA = 25 °C | 68 | |
| Low power low voltage regulator usage (VDD=3.3 V) | IDD_STOP | 10 | 28 | µA | TA = 25 °C | 68 | |
| Supply current in Standby mode, low-speed oscillator (LSE) and RTC ON (VDD=3.3 V) | IDD_STBY | 2.8 | 5 | µA | TA = 25 °C | 69 | |
| Supply current in Standby mode, RTC and LSE OFF (VDD=3.3 V) | IDD_STBY | 2.1 | 4 | µA | TA = 25 °C | 69 | |
| Voltage-regulator internal voltage on VCAP_1/VCAP_2 external capacitor | CEXT | 2.2 | µF | with available VCAP_1 and VCAP_2 pins | 61 |
CAD (KiCad official)
- Symbol:
STM32F401CBU7 - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm32f401cbu7-etched.step/stm32f401cbu7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f401cbu7.step/stm32f401cbu7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (139 pp, sha256
c38f92aa9d66e8cb, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).