← Commit history

Initial commit: component/stm32f205rct6

Ray ·08a78e0e4b ·
2 files changed +591
README.mdadded+100
@@ -0,0 +1,100 @@+# STM32F205RCT6++**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)++STM32F205RCT6 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VBAT | power_in | Battery supply for RTC, 20×32-bit backup registers, and optional 4 KB backup SRAM; stays powered when VDD is removed. |+| 2 | PC13 | bidirectional | 5 V-tolerant I/O supplied through power switch; output limited to ≤2 MHz and ≤30 pF load (max 3 mA switch current); alternate function RTC_AF1 after first backup-domain power-up. |+| 3 | PC14-OSC32_IN | bidirectional | 5 V-tolerant I/O or 32.768 kHz crystal oscillator input (OSC32_IN); output limited to ≤2 MHz / ≤30 pF; not 5 V-tolerant in oscillator mode. |+| 4 | PC15-OSC32_OUT | bidirectional | 5 V-tolerant I/O or 32.768 kHz crystal oscillator output (OSC32_OUT); output limited to ≤2 MHz / ≤30 pF; not 5 V-tolerant in oscillator mode. |+| 5 | PH0-OSC_IN | bidirectional | 5 V-tolerant I/O or 4-26 MHz high-speed external crystal oscillator input (OSC_IN); not 5 V-tolerant in oscillator mode. |+| 6 | PH1-OSC_OUT | bidirectional | 5 V-tolerant I/O or 4-26 MHz high-speed external crystal oscillator output (OSC_OUT); not 5 V-tolerant in oscillator mode. |+| 7 | NRST | bidirectional | Bidirectional system reset pin with embedded weak pull-up resistor; active-low; filters glitches shorter than the minimum pulse width. |+| 8 | PC0 | bidirectional | 5 V-tolerant I/O with ADC123_IN10 analog input; alternate function OTG_HS_ULPI_STP. |+| 9 | PC1 | bidirectional | 5 V-tolerant I/O with ADC123_IN11 analog input; alternate function ETH_MDC. |+| 10 | PC2 | bidirectional | 5 V-tolerant I/O with ADC123_IN12 analog input; alternate functions SPI2_MISO, OTG_HS_ULPI_DIR, ETH_MII_TXD2. |+| 11 | PC3 | bidirectional | 5 V-tolerant I/O with ADC123_IN13 analog input; alternate functions SPI2_MOSI/I2S2_SD, OTG_HS_ULPI_NXT, ETH_MII_TX_CLK. |+| 12 | VSSA | power_in | Analog ground reference for ADC, DAC, and embedded reference voltage; must be tied to VSS. |+| 13 | VDDA | power_in | Analog supply for ADC, DAC, reset block, and RC oscillators; 1.8-3.6 V. |+| 14 | PA0-WKUP | bidirectional | 5 V-tolerant I/O with Standby wake-up (WKUP) and ADC123_IN0 analog input; alternate functions USART2_CTS, UART4_TX, TIM2_CH1_ETR, TIM5_CH1, TIM8_ETR, ETH_MII_CRS. |+| 15 | PA1 | bidirectional | 5 V-tolerant I/O with ADC123_IN1 analog input; alternate functions USART2_RTS, UART4_RX, ETH_RMII_REF_CLK/ETH_MII_RX_CLK, TIM5_CH2, TIM2_CH2. |+| 16 | PA2 | bidirectional | 5 V-tolerant I/O with ADC123_IN2 analog input; alternate functions USART2_TX, TIM5_CH3, TIM9_CH1, TIM2_CH3, ETH_MDIO. |+| 17 | PA3 | bidirectional | 5 V-tolerant I/O with ADC123_IN3 analog input; alternate functions USART2_RX, TIM5_CH4, TIM9_CH2, TIM2_CH4, OTG_HS_ULPI_D0, ETH_MII_COL. |+| 18 | VSS | power_in | Digital ground supply; 0 V reference for all digital circuitry. |+| 19 | VDD | power_in | Main digital supply; 1.8-3.6 V for I/O buffers and digital core. |+| 20 | PA4 | bidirectional | 3.3 V-tolerant I/O (TTa) with ADC12_IN4 analog input and DAC_OUT1 analog output; alternate functions SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK, DCMI_HSYNC, OTG_HS_SOF. |+| 21 | PA5 | bidirectional | 3.3 V-tolerant I/O (TTa) with ADC12_IN5 analog input and DAC_OUT2 analog output; alternate functions SPI1_SCK, OTG_HS_ULPI_CK, TIM2_CH1_ETR, TIM8_CH1N. |+| 22 | PA6 | bidirectional | 5 V-tolerant I/O with ADC12_IN6 analog input; alternate functions SPI1_MISO, TIM8_BKIN, TIM13_CH1, DCMI_PIXCLK, TIM3_CH1, TIM1_BKIN. |+| 23 | PA7 | bidirectional | 5 V-tolerant I/O with ADC12_IN7 analog input; alternate functions SPI1_MOSI, TIM8_CH1N, TIM14_CH1, TIM3_CH2, ETH_MII_RX_DV/ETH_RMII_CRS_DV, TIM1_CH1N. |+| 24 | PC4 | bidirectional | 5 V-tolerant I/O with ADC12_IN14 analog input; alternate functions ETH_RMII_RXD0, ETH_MII_RXD0. |+| 25 | PC5 | bidirectional | 5 V-tolerant I/O with ADC12_IN15 analog input; alternate functions ETH_RMII_RXD1, ETH_MII_RXD1. |+| 26 | PB0 | bidirectional | 5 V-tolerant I/O with ADC12_IN8 analog input; alternate functions TIM3_CH3, TIM8_CH2N, OTG_HS_ULPI_D1, ETH_MII_RXD2, TIM1_CH2N. |+| 27 | PB1 | bidirectional | 5 V-tolerant I/O with ADC12_IN9 analog input; alternate functions TIM3_CH4, TIM8_CH3N, OTG_HS_ULPI_D2, ETH_MII_RXD3, TIM1_CH3N. |+| 28 | PB2 | bidirectional | 5 V-tolerant I/O; used with BOOT0 to select boot mode at reset (BOOT1 function). |+| 29 | PB10 | bidirectional | 5 V-tolerant I/O; alternate functions SPI2_SCK/I2S2_SCK, I2C2_SCL, USART3_TX, OTG_HS_ULPI_D3, ETH_MII_RX_ER, TIM2_CH3. |+| 30 | PB11 | bidirectional | 5 V-tolerant I/O; alternate functions I2C2_SDA, USART3_RX, OTG_HS_ULPI_D4, ETH_RMII_TX_EN/ETH_MII_TX_EN, TIM2_CH4. |+| 31 | VCAP_1 | passive | Internal core-domain LDO output 1; requires 2.2 µF external decoupling capacitor to VSS; must not be connected to VDD. |+| 32 | VDD | power_in | Main digital supply; 1.8-3.6 V for I/O buffers and digital core. |+| 33 | PB12 | bidirectional | 5 V-tolerant I/O; alternate functions SPI2_NSS/I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN, CAN2_RX, OTG_HS_ULPI_D5, ETH_RMII_TXD0/ETH_MII_TXD0, OTG_HS_ID. |+| 34 | PB13 | bidirectional | 5 V-tolerant I/O with OTG_HS_VBUS monitor function; alternate functions SPI2_SCK/I2S2_SCK, USART3_CTS, TIM1_CH1N, CAN2_TX, OTG_HS_ULPI_D6, ETH_RMII_TXD1/ETH_MII_TXD1. |+| 35 | PB14 | bidirectional | 5 V-tolerant I/O; alternate functions SPI2_MISO, TIM1_CH2N, TIM12_CH1, OTG_HS_DM, USART3_RTS, TIM8_CH2N. |+| 36 | PB15 | bidirectional | 5 V-tolerant I/O; alternate functions SPI2_MOSI/I2S2_SD, TIM1_CH3N, TIM8_CH3N, TIM12_CH2, OTG_HS_DP, RTC_50Hz. |+| 37 | PC6 | bidirectional | 5 V-tolerant I/O; alternate functions I2S2_MCK, TIM8_CH1, SDIO_D6, USART6_TX, DCMI_D0, TIM3_CH1. |+| 38 | PC7 | bidirectional | 5 V-tolerant I/O; alternate functions I2S3_MCK, TIM8_CH2, SDIO_D7, USART6_RX, DCMI_D1, TIM3_CH2. |+| 39 | PC8 | bidirectional | 5 V-tolerant I/O; alternate functions TIM8_CH3, SDIO_D0, TIM3_CH3, USART6_CK, DCMI_D2. |+| 40 | PC9 | bidirectional | 5 V-tolerant I/O; alternate functions MCO2, I2S2_CKIN/I2S3_CKIN, TIM8_CH4, SDIO_D1, I2C3_SDA, DCMI_D3, TIM3_CH4. |+| 41 | PA8 | bidirectional | 5 V-tolerant I/O; alternate functions MCO1, USART1_CK, TIM1_CH1, I2C3_SCL, OTG_FS_SOF. |+| 42 | PA9 | bidirectional | 5 V-tolerant I/O with OTG_FS_VBUS monitor function; alternate functions USART1_TX, TIM1_CH2, I2C3_SMBA, DCMI_D0. |+| 43 | PA10 | bidirectional | 5 V-tolerant I/O; alternate functions USART1_RX, TIM1_CH3, OTG_FS_ID, DCMI_D1. |+| 44 | PA11 | bidirectional | 5 V-tolerant I/O; alternate functions USART1_CTS, CAN1_RX, TIM1_CH4, OTG_FS_DM. |+| 45 | PA12 | bidirectional | 5 V-tolerant I/O; alternate functions USART1_RTS, CAN1_TX, TIM1_ETR, OTG_FS_DP. |+| 46 | PA13 | bidirectional | 5 V-tolerant I/O; default function JTAG TMS / SWD data I/O (JTMS-SWDIO) active after reset. |+| 47 | VCAP_2 | passive | Internal core-domain LDO output 2; requires 2.2 µF external decoupling capacitor to VSS; must not be connected to VDD. |+| 48 | VDD | power_in | Main digital supply; 1.8-3.6 V for I/O buffers and digital core. |+| 49 | PA14 | bidirectional | 5 V-tolerant I/O; default function JTAG TCK / SWD clock (JTCK-SWCLK) active after reset. |+| 50 | PA15 | bidirectional | 5 V-tolerant I/O; default function JTAG TDI (JTDI) active after reset; alternate functions SPI3_NSS/I2S3_WS, TIM2_CH1_ETR, SPI1_NSS. |+| 51 | PC10 | bidirectional | 5 V-tolerant I/O; alternate functions SPI3_SCK/I2S3_SCK, UART4_TX, SDIO_D2, DCMI_D8, USART3_TX. |+| 52 | PC11 | bidirectional | 5 V-tolerant I/O; alternate functions UART4_RX, SPI3_MISO, SDIO_D3, DCMI_D4, USART3_RX. |+| 53 | PC12 | bidirectional | 5 V-tolerant I/O; alternate functions UART5_TX, SDIO_CK, DCMI_D9, SPI3_MOSI/I2S3_SD, USART3_CK. |+| 54 | PD2 | bidirectional | 5 V-tolerant I/O; alternate functions TIM3_ETR, UART5_RX, SDIO_CMD, DCMI_D11. |+| 55 | PB3 | bidirectional | 5 V-tolerant I/O; default function JTAG TDO / Trace SWO (JTDO/TRACESWO) active after reset; alternate functions SPI3_SCK/I2S3_SCK, TIM2_CH2, SPI1_SCK. |+| 56 | PB4 | bidirectional | 5 V-tolerant I/O; default function NJTRST active after reset; alternate functions SPI3_MISO, TIM3_CH1, SPI1_MISO. |+| 57 | PB5 | bidirectional | 5 V-tolerant I/O; alternate functions I2C1_SMBA, CAN2_RX, OTG_HS_ULPI_D7, ETH_PPS_OUT, TIM3_CH2, SPI1_MOSI, SPI3_MOSI/I2S3_SD, DCMI_D10. |+| 58 | PB6 | bidirectional | 5 V-tolerant I/O; alternate functions I2C1_SCL, TIM4_CH1, CAN2_TX, DCMI_D5, USART1_TX. |+| 59 | PB7 | bidirectional | 5 V-tolerant I/O; alternate functions I2C1_SDA, FSMC_NL/NADV, DCMI_VSYNC, USART1_RX, TIM4_CH2. |+| 60 | BOOT0 | input | Dedicated BOOT0 input (type I, structure B) for selecting boot mode at reset in combination with BOOT1/PB2; also serves as VPP for Flash programming. |+| 61 | PB8 | bidirectional | 5 V-tolerant I/O; alternate functions TIM4_CH3, SDIO_D4, TIM10_CH1, DCMI_D6, ETH_MII_TXD3, I2C1_SCL, CAN1_RX. |+| 62 | PB9 | bidirectional | 5 V-tolerant I/O; alternate functions SPI2_NSS/I2S2_WS, TIM4_CH4, TIM11_CH1, SDIO_D5, DCMI_D7, I2C1_SDA, CAN1_TX. |+| 63 | VSS | power_in | Digital ground supply; 0 V reference for all digital circuitry. |+| 64 | VDD | power_in | Main digital supply; 1.8-3.6 V for I/O buffers and digital core. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LQFP-64(10x10) |+| Category | Embedded Processors & Controllers |+| Pins | 64 |++## CAD (KiCad official)++- Symbol: `STM32F205RCT6`+- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`+- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)+- 3D model files: `stm32f205rct6-etched.step` / `stm32f205rct6-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32f205rct6.step` / `stm32f205rct6.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586176523259166720) (179 pp, sha256 `6ffebd41462b5c10`, retrieved 2026-09-27, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/stm32f205rct6-datasheet.pdf)
page.jsonadded+491
@@ -0,0 +1,491 @@+{+  "slug": "stm32f205rct6",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "embedded processors & controllers",+    "stm32f205rct6",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "stm32f205rct6.kicad_sym",+    "stm32f205rct6.kicad_mod",+    "stm32f205rct6.glb",+    "stm32f205rct6.step",+    "stm32f205rct6.lbr",+    "docs/hero.png",+    "docs/stm32f205rct6-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "STM32F205RCT6",+    "manufacturer": "STMicroelectronics",+    "package": "LQFP-64(10x10)",+    "pin_count": 64,+    "category": "Embedded Processors & Controllers",+    "subcategory": "Microcontrollers (MCU/MPU/SOC)",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586176523259166720",+    "parts": {+      "symbol": "stm32f205rct6.kicad_sym",+      "footprint": "stm32f205rct6.kicad_mod",+      "model_3d": "stm32f205rct6-etched.glb",+      "model_3d_plain": "stm32f205rct6.glb",+      "model_3d_step": "stm32f205rct6-etched.step",+      "model_3d_step_plain": "stm32f205rct6.step",+      "lbr": "stm32f205rct6.lbr"+    },+    "distributor_links": {+      "lcsc": "C47520",+      "digikey": "497-11154-ND",+      "mouser": "511-STM32F205RCT6"+    },+    "distributor_check": {+      "checked_at": "2026-09-27T08:45:16Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "497-11154-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "511-STM32F205RCT6",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "VBAT",+        "type": "power_in",+        "description": "Battery supply for RTC, 20×32-bit backup registers, and optional 4 KB backup SRAM; stays powered when VDD is removed."+      },+      {+        "number": "2",+        "name": "PC13",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O supplied through power switch; output limited to ≤2 MHz and ≤30 pF load (max 3 mA switch current); alternate function RTC_AF1 after first backup-domain power-up."+      },+      {+        "number": "3",+        "name": "PC14-OSC32_IN",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O or 32.768 kHz crystal oscillator input (OSC32_IN); output limited to ≤2 MHz / ≤30 pF; not 5 V-tolerant in oscillator mode."+      },+      {+        "number": "4",+        "name": "PC15-OSC32_OUT",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O or 32.768 kHz crystal oscillator output (OSC32_OUT); output limited to ≤2 MHz / ≤30 pF; not 5 V-tolerant in oscillator mode."+      },+      {+        "number": "5",+        "name": "PH0-OSC_IN",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O or 4-26 MHz high-speed external crystal oscillator input (OSC_IN); not 5 V-tolerant in oscillator mode."+      },+      {+        "number": "6",+        "name": "PH1-OSC_OUT",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O or 4-26 MHz high-speed external crystal oscillator output (OSC_OUT); not 5 V-tolerant in oscillator mode."+      },+      {+        "number": "7",+        "name": "NRST",+        "type": "bidirectional",+        "description": "Bidirectional system reset pin with embedded weak pull-up resistor; active-low; filters glitches shorter than the minimum pulse width."+      },+      {+        "number": "8",+        "name": "PC0",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC123_IN10 analog input; alternate function OTG_HS_ULPI_STP."+      },+      {+        "number": "9",+        "name": "PC1",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC123_IN11 analog input; alternate function ETH_MDC."+      },+      {+        "number": "10",+        "name": "PC2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC123_IN12 analog input; alternate functions SPI2_MISO, OTG_HS_ULPI_DIR, ETH_MII_TXD2."+      },+      {+        "number": "11",+        "name": "PC3",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC123_IN13 analog input; alternate functions SPI2_MOSI/I2S2_SD, OTG_HS_ULPI_NXT, ETH_MII_TX_CLK."+      },+      {+        "number": "12",+        "name": "VSSA",+        "type": "power_in",+        "description": "Analog ground reference for ADC, DAC, and embedded reference voltage; must be tied to VSS."+      },+      {+        "number": "13",+        "name": "VDDA",+        "type": "power_in",+        "description": "Analog supply for ADC, DAC, reset block, and RC oscillators; 1.8-3.6 V."+      },+      {+        "number": "14",+        "name": "PA0-WKUP",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with Standby wake-up (WKUP) and ADC123_IN0 analog input; alternate functions USART2_CTS, UART4_TX, TIM2_CH1_ETR, TIM5_CH1, TIM8_ETR, ETH_MII_CRS."+      },+      {+        "number": "15",+        "name": "PA1",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC123_IN1 analog input; alternate functions USART2_RTS, UART4_RX, ETH_RMII_REF_CLK/ETH_MII_RX_CLK, TIM5_CH2, TIM2_CH2."+      },+      {+        "number": "16",+        "name": "PA2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC123_IN2 analog input; alternate functions USART2_TX, TIM5_CH3, TIM9_CH1, TIM2_CH3, ETH_MDIO."+      },+      {+        "number": "17",+        "name": "PA3",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC123_IN3 analog input; alternate functions USART2_RX, TIM5_CH4, TIM9_CH2, TIM2_CH4, OTG_HS_ULPI_D0, ETH_MII_COL."+      },+      {+        "number": "18",+        "name": "VSS",+        "type": "power_in",+        "description": "Digital ground supply; 0 V reference for all digital circuitry."+      },+      {+        "number": "19",+        "name": "VDD",+        "type": "power_in",+        "description": "Main digital supply; 1.8-3.6 V for I/O buffers and digital core."+      },+      {+        "number": "20",+        "name": "PA4",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O (TTa) with ADC12_IN4 analog input and DAC_OUT1 analog output; alternate functions SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK, DCMI_HSYNC, OTG_HS_SOF."+      },+      {+        "number": "21",+        "name": "PA5",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O (TTa) with ADC12_IN5 analog input and DAC_OUT2 analog output; alternate functions SPI1_SCK, OTG_HS_ULPI_CK, TIM2_CH1_ETR, TIM8_CH1N."+      },+      {+        "number": "22",+        "name": "PA6",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC12_IN6 analog input; alternate functions SPI1_MISO, TIM8_BKIN, TIM13_CH1, DCMI_PIXCLK, TIM3_CH1, TIM1_BKIN."+      },+      {+        "number": "23",+        "name": "PA7",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC12_IN7 analog input; alternate functions SPI1_MOSI, TIM8_CH1N, TIM14_CH1, TIM3_CH2, ETH_MII_RX_DV/ETH_RMII_CRS_DV, TIM1_CH1N."+      },+      {+        "number": "24",+        "name": "PC4",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC12_IN14 analog input; alternate functions ETH_RMII_RXD0, ETH_MII_RXD0."+      },+      {+        "number": "25",+        "name": "PC5",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC12_IN15 analog input; alternate functions ETH_RMII_RXD1, ETH_MII_RXD1."+      },+      {+        "number": "26",+        "name": "PB0",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC12_IN8 analog input; alternate functions TIM3_CH3, TIM8_CH2N, OTG_HS_ULPI_D1, ETH_MII_RXD2, TIM1_CH2N."+      },+      {+        "number": "27",+        "name": "PB1",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with ADC12_IN9 analog input; alternate functions TIM3_CH4, TIM8_CH3N, OTG_HS_ULPI_D2, ETH_MII_RXD3, TIM1_CH3N."+      },+      {+        "number": "28",+        "name": "PB2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; used with BOOT0 to select boot mode at reset (BOOT1 function)."+      },+      {+        "number": "29",+        "name": "PB10",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions SPI2_SCK/I2S2_SCK, I2C2_SCL, USART3_TX, OTG_HS_ULPI_D3, ETH_MII_RX_ER, TIM2_CH3."+      },+      {+        "number": "30",+        "name": "PB11",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions I2C2_SDA, USART3_RX, OTG_HS_ULPI_D4, ETH_RMII_TX_EN/ETH_MII_TX_EN, TIM2_CH4."+      },+      {+        "number": "31",+        "name": "VCAP_1",+        "type": "passive",+        "description": "Internal core-domain LDO output 1; requires 2.2 µF external decoupling capacitor to VSS; must not be connected to VDD."+      },+      {+        "number": "32",+        "name": "VDD",+        "type": "power_in",+        "description": "Main digital supply; 1.8-3.6 V for I/O buffers and digital core."+      },+      {+        "number": "33",+        "name": "PB12",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions SPI2_NSS/I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN, CAN2_RX, OTG_HS_ULPI_D5, ETH_RMII_TXD0/ETH_MII_TXD0, OTG_HS_ID."+      },+      {+        "number": "34",+        "name": "PB13",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with OTG_HS_VBUS monitor function; alternate functions SPI2_SCK/I2S2_SCK, USART3_CTS, TIM1_CH1N, CAN2_TX, OTG_HS_ULPI_D6, ETH_RMII_TXD1/ETH_MII_TXD1."+      },+      {+        "number": "35",+        "name": "PB14",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions SPI2_MISO, TIM1_CH2N, TIM12_CH1, OTG_HS_DM, USART3_RTS, TIM8_CH2N."+      },+      {+        "number": "36",+        "name": "PB15",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions SPI2_MOSI/I2S2_SD, TIM1_CH3N, TIM8_CH3N, TIM12_CH2, OTG_HS_DP, RTC_50Hz."+      },+      {+        "number": "37",+        "name": "PC6",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions I2S2_MCK, TIM8_CH1, SDIO_D6, USART6_TX, DCMI_D0, TIM3_CH1."+      },+      {+        "number": "38",+        "name": "PC7",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions I2S3_MCK, TIM8_CH2, SDIO_D7, USART6_RX, DCMI_D1, TIM3_CH2."+      },+      {+        "number": "39",+        "name": "PC8",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions TIM8_CH3, SDIO_D0, TIM3_CH3, USART6_CK, DCMI_D2."+      },+      {+        "number": "40",+        "name": "PC9",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions MCO2, I2S2_CKIN/I2S3_CKIN, TIM8_CH4, SDIO_D1, I2C3_SDA, DCMI_D3, TIM3_CH4."+      },+      {+        "number": "41",+        "name": "PA8",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions MCO1, USART1_CK, TIM1_CH1, I2C3_SCL, OTG_FS_SOF."+      },+      {+        "number": "42",+        "name": "PA9",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with OTG_FS_VBUS monitor function; alternate functions USART1_TX, TIM1_CH2, I2C3_SMBA, DCMI_D0."+      },+      {+        "number": "43",+        "name": "PA10",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions USART1_RX, TIM1_CH3, OTG_FS_ID, DCMI_D1."+      },+      {+        "number": "44",+        "name": "PA11",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions USART1_CTS, CAN1_RX, TIM1_CH4, OTG_FS_DM."+      },+      {+        "number": "45",+        "name": "PA12",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions USART1_RTS, CAN1_TX, TIM1_ETR, OTG_FS_DP."+      },+      {+        "number": "46",+        "name": "PA13",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; default function JTAG TMS / SWD data I/O (JTMS-SWDIO) active after reset."+      },+      {+        "number": "47",+        "name": "VCAP_2",+        "type": "passive",+        "description": "Internal core-domain LDO output 2; requires 2.2 µF external decoupling capacitor to VSS; must not be connected to VDD."+      },+      {+        "number": "48",+        "name": "VDD",+        "type": "power_in",+        "description": "Main digital supply; 1.8-3.6 V for I/O buffers and digital core."+      },+      {+        "number": "49",+        "name": "PA14",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; default function JTAG TCK / SWD clock (JTCK-SWCLK) active after reset."+      },+      {+        "number": "50",+        "name": "PA15",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; default function JTAG TDI (JTDI) active after reset; alternate functions SPI3_NSS/I2S3_WS, TIM2_CH1_ETR, SPI1_NSS."+      },+      {+        "number": "51",+        "name": "PC10",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions SPI3_SCK/I2S3_SCK, UART4_TX, SDIO_D2, DCMI_D8, USART3_TX."+      },+      {+        "number": "52",+        "name": "PC11",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions UART4_RX, SPI3_MISO, SDIO_D3, DCMI_D4, USART3_RX."+      },+      {+        "number": "53",+        "name": "PC12",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions UART5_TX, SDIO_CK, DCMI_D9, SPI3_MOSI/I2S3_SD, USART3_CK."+      },+      {+        "number": "54",+        "name": "PD2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions TIM3_ETR, UART5_RX, SDIO_CMD, DCMI_D11."+      },+      {+        "number": "55",+        "name": "PB3",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; default function JTAG TDO / Trace SWO (JTDO/TRACESWO) active after reset; alternate functions SPI3_SCK/I2S3_SCK, TIM2_CH2, SPI1_SCK."+      },+      {+        "number": "56",+        "name": "PB4",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; default function NJTRST active after reset; alternate functions SPI3_MISO, TIM3_CH1, SPI1_MISO."+      },+      {+        "number": "57",+        "name": "PB5",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions I2C1_SMBA, CAN2_RX, OTG_HS_ULPI_D7, ETH_PPS_OUT, TIM3_CH2, SPI1_MOSI, SPI3_MOSI/I2S3_SD, DCMI_D10."+      },+      {+        "number": "58",+        "name": "PB6",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions I2C1_SCL, TIM4_CH1, CAN2_TX, DCMI_D5, USART1_TX."+      },+      {+        "number": "59",+        "name": "PB7",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions I2C1_SDA, FSMC_NL/NADV, DCMI_VSYNC, USART1_RX, TIM4_CH2."+      },+      {+        "number": "60",+        "name": "BOOT0",+        "type": "input",+        "description": "Dedicated BOOT0 input (type I, structure B) for selecting boot mode at reset in combination with BOOT1/PB2; also serves as VPP for Flash programming."+      },+      {+        "number": "61",+        "name": "PB8",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions TIM4_CH3, SDIO_D4, TIM10_CH1, DCMI_D6, ETH_MII_TXD3, I2C1_SCL, CAN1_RX."+      },+      {+        "number": "62",+        "name": "PB9",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O; alternate functions SPI2_NSS/I2S2_WS, TIM4_CH4, TIM11_CH1, SDIO_D5, DCMI_D7, I2C1_SDA, CAN1_TX."+      },+      {+        "number": "63",+        "name": "VSS",+        "type": "power_in",+        "description": "Digital ground supply; 0 V reference for all digital circuitry."+      },+      {+        "number": "64",+        "name": "VDD",+        "type": "power_in",+        "description": "Main digital supply; 1.8-3.6 V for I/O buffers and digital core."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 57,+        "cost_usd": 1.5652,+        "at": "2026-09-27T08:44:50"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586176523259166720",+        "pages": 179,+        "sha256": "6ffebd41462b5c10",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 64,+        "described": 64,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file