← Commit history

Initial commit: component/stm32f103c8t7

Ray ·d66fd724e1 ·
2 files changed +467
README.mdadded+84
@@ -0,0 +1,84 @@+# STM32F103C8T7++**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)++STM32F103C8T7 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VBAT | power_in | Power supply for RTC, external 32 kHz oscillator and backup registers (through power switch) when VDD is not present; VBAT = 1.8 to 3.6 V. |+| 2 | PC13-TAMPER-RTC | bidirectional | GPIO port C bit 13, shared with TAMPER-RTC alternate function; supplied through the backup power switch (3 mA max sink/source), output speed limited to 2 MHz with 30 pF load and must not be used as a current source. |+| 3 | PC14-OSC32_IN | bidirectional | GPIO port C bit 14, main function after first backup domain power-up; alternate function OSC32_IN (32.768 kHz RTC crystal input); supplied through the backup power switch (3 mA max, 2 MHz max output speed). |+| 4 | PC15-OSC32_OUT | bidirectional | GPIO port C bit 15, main function after first backup domain power-up; alternate function OSC32_OUT (32.768 kHz RTC crystal output); supplied through the backup power switch (3 mA max, 2 MHz max output speed). |+| 5 | OSC_IN | input | Input of the 4-16 MHz high-speed external (HSE) crystal/ceramic resonator oscillator; can be remapped by software to GPIO PD0 (limited to 50 MHz in output mode). |+| 6 | OSC_OUT | output | Output of the 4-16 MHz high-speed external (HSE) crystal/ceramic resonator oscillator; can be remapped by software to GPIO PD1 (limited to 50 MHz in output mode). |+| 7 | NRST | bidirectional | Active-low system reset input/output with a permanent internal pull-up resistor (RPU) to VDD; a low level on this pin generates a device reset. |+| 8 | VSSA | power_in | Analog ground supply for the ADC, reset blocks, RC oscillators and PLL; must be connected to VSS. |+| 9 | VDDA | power_in | External analog power supply for ADC, reset blocks, RC oscillators and PLL, 2.0 to 3.6 V (minimum 2.4 V when the ADC is used); must be connected to VDD. |+| 10 | PA0-WKUP | bidirectional | GPIO port A bit 0, 5 V tolerant; alternate functions WKUP (standby wakeup), USART2_CTS, ADC12_IN0, TIM2_CH1_ETR. |+| 11 | PA1 | bidirectional | GPIO port A bit 1, 5 V tolerant; alternate functions USART2_RTS, ADC12_IN1, TIM2_CH2. |+| 12 | PA2 | bidirectional | GPIO port A bit 2, 5 V tolerant; alternate functions USART2_TX, ADC12_IN2, TIM2_CH3. |+| 13 | PA3 | bidirectional | GPIO port A bit 3, 5 V tolerant; alternate functions USART2_RX, ADC12_IN3, TIM2_CH4. |+| 14 | PA4 | bidirectional | GPIO port A bit 4, 5 V tolerant; alternate functions SPI1_NSS, USART2_CK, ADC12_IN4. |+| 15 | PA5 | bidirectional | GPIO port A bit 5, 5 V tolerant; alternate functions SPI1_SCK, ADC12_IN5. |+| 16 | PA6 | bidirectional | GPIO port A bit 6, 5 V tolerant; default alternate functions SPI1_MISO, ADC12_IN6, TIM3_CH1, remappable to TIM1_BKIN. |+| 17 | PA7 | bidirectional | GPIO port A bit 7, 5 V tolerant; default alternate functions SPI1_MOSI, ADC12_IN7, TIM3_CH2, remappable to TIM1_CH1N. |+| 18 | PB0 | bidirectional | GPIO port B bit 0, 5 V tolerant; default alternate functions ADC12_IN8, TIM3_CH3, remappable to TIM1_CH2N. |+| 19 | PB1 | bidirectional | GPIO port B bit 1, 5 V tolerant; default alternate functions ADC12_IN9, TIM3_CH4, remappable to TIM1_CH3N. |+| 20 | PB2/BOOT1 | bidirectional | GPIO port B bit 2, 5 V tolerant, shared with BOOT1; sampled together with BOOT0 at reset to select the boot mode (Flash, System memory or SRAM). |+| 21 | PB10 | bidirectional | GPIO port B bit 10, 5 V tolerant; default alternate functions I2C2_SCL, USART3_TX, remappable to TIM2_CH3. |+| 22 | PB11 | bidirectional | GPIO port B bit 11, 5 V tolerant; default alternate functions I2C2_SDA, USART3_RX, remappable to TIM2_CH4. |+| 23 | VSS_1 | power_in | Digital ground supply pin. |+| 24 | VDD_1 | power_in | External digital power supply pin, 2.0 to 3.6 V, for I/Os and internal regulator. |+| 25 | PB12 | bidirectional | GPIO port B bit 12, 5 V tolerant; alternate functions SPI2_NSS, I2C2_SMBAl, USART3_CK, TIM1_BKIN. |+| 26 | PB13 | bidirectional | GPIO port B bit 13, 5 V tolerant; alternate functions SPI2_SCK, USART3_CTS, TIM1_CH1N. |+| 27 | PB14 | bidirectional | GPIO port B bit 14, 5 V tolerant; alternate functions SPI2_MISO, USART3_RTS, TIM1_CH2N. |+| 28 | PB15 | bidirectional | GPIO port B bit 15, 5 V tolerant; alternate functions SPI2_MOSI, TIM1_CH3N. |+| 29 | PA8 | bidirectional | GPIO port A bit 8, 5 V tolerant; alternate functions USART1_CK, TIM1_CH1, MCO. |+| 30 | PA9 | bidirectional | GPIO port A bit 9, 5 V tolerant; alternate functions USART1_TX, TIM1_CH2. |+| 31 | PA10 | bidirectional | GPIO port A bit 10, 5 V tolerant; alternate functions USART1_RX, TIM1_CH3. |+| 32 | PA11 | bidirectional | GPIO port A bit 11, 5 V tolerant; alternate functions USART1_CTS, CANRX, USBDM, TIM1_CH4. |+| 33 | PA12 | bidirectional | GPIO port A bit 12, 5 V tolerant; alternate functions USART1_RTS, CANTX, USBDP, TIM1_ETR. |+| 34 | PA13 | bidirectional | GPIO port A bit 13, 5 V tolerant; default function JTMS/SWDIO debug interface pin. |+| 35 | VSS_2 | power_in | Digital ground supply pin. |+| 36 | VDD_2 | power_in | External digital power supply pin, 2.0 to 3.6 V, for I/Os and internal regulator. |+| 37 | PA14 | bidirectional | GPIO port A bit 14, 5 V tolerant; default function JTCK/SWCLK debug interface pin. |+| 38 | PA15 | bidirectional | GPIO port A bit 15, 5 V tolerant; default function JTDI, remappable to TIM2_CH1_ETR/SPI1_NSS. |+| 39 | PB3 | bidirectional | GPIO port B bit 3, 5 V tolerant; default function JTDO, remappable to TIM2_CH2/TRACESWO/SPI1_SCK. |+| 40 | PB4 | bidirectional | GPIO port B bit 4, 5 V tolerant; default function JNTRST, remappable to TIM3_CH1/SPI1_MISO. |+| 41 | PB5 | bidirectional | GPIO port B bit 5 (standard, not 5 V tolerant); default alternate function I2C1_SMBAl, remappable to TIM3_CH2/SPI1_MOSI. |+| 42 | PB6 | bidirectional | GPIO port B bit 6, 5 V tolerant; default alternate functions I2C1_SCL, TIM4_CH1, remappable to USART1_TX. |+| 43 | PB7 | bidirectional | GPIO port B bit 7, 5 V tolerant; default alternate functions I2C1_SDA, TIM4_CH2, remappable to USART1_RX. |+| 44 | BOOT0 | input | Boot mode selection pin, sampled together with BOOT1 (PB2) at reset to select boot from user Flash, system memory or embedded SRAM. |+| 45 | PB8 | bidirectional | GPIO port B bit 8, 5 V tolerant; default alternate function TIM4_CH3, remappable to I2C1_SCL/CANRX. |+| 46 | PB9 | bidirectional | GPIO port B bit 9, 5 V tolerant; default alternate function TIM4_CH4, remappable to I2C1_SDA/CANTX. |+| 47 | VSS_3 | power_in | Digital ground supply pin. |+| 48 | VDD_3 | power_in | External digital power supply pin, 2.0 to 3.6 V, for I/Os and internal regulator; the 4.7 µF decoupling capacitor must be connected to this VDD3 pin. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LQFP-48(7x7) |+| Category | Embedded Processors & Controllers |+| Pins | 48 |++## CAD (KiCad official)++- Symbol: `STM32F103C8T7`+- Footprint: `Package_QFP:LQFP-48_7x7mm_P0.5mm`+- 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)+- 3D model files: `stm32f103c8t7-etched.step` / `stm32f103c8t7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32f103c8t7.step` / `stm32f103c8t7.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590903672543133697) (117 pp, sha256 `4741c03c5793745c`, retrieved 2026-09-24, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/stm32f103c8t7-datasheet.pdf)
page.jsonadded+383
@@ -0,0 +1,383 @@+{+  "slug": "stm32f103c8t7",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-48(7x7). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "embedded processors & controllers",+    "stm32f103c8t7",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "stm32f103c8t7.kicad_sym",+    "stm32f103c8t7.kicad_mod",+    "stm32f103c8t7.glb",+    "stm32f103c8t7.step",+    "stm32f103c8t7.lbr",+    "docs/hero.png",+    "docs/stm32f103c8t7-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "STM32F103C8T7",+    "manufacturer": "STMicroelectronics",+    "package": "LQFP-48(7x7)",+    "pin_count": 48,+    "category": "Embedded Processors & Controllers",+    "subcategory": "Microcontrollers (MCU/MPU/SOC)",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590903672543133697",+    "parts": {+      "symbol": "stm32f103c8t7.kicad_sym",+      "footprint": "stm32f103c8t7.kicad_mod",+      "model_3d": "stm32f103c8t7-etched.glb",+      "model_3d_plain": "stm32f103c8t7.glb",+      "model_3d_step": "stm32f103c8t7-etched.step",+      "model_3d_step_plain": "stm32f103c8t7.step",+      "lbr": "stm32f103c8t7.lbr"+    },+    "distributor_links": {+      "lcsc": "C1121900"+    },+    "pins": [+      {+        "number": "1",+        "name": "VBAT",+        "type": "power_in",+        "description": "Power supply for RTC, external 32 kHz oscillator and backup registers (through power switch) when VDD is not present; VBAT = 1.8 to 3.6 V."+      },+      {+        "number": "2",+        "name": "PC13-TAMPER-RTC",+        "type": "bidirectional",+        "description": "GPIO port C bit 13, shared with TAMPER-RTC alternate function; supplied through the backup power switch (3 mA max sink/source), output speed limited to 2 MHz with 30 pF load and must not be used as a current source."+      },+      {+        "number": "3",+        "name": "PC14-OSC32_IN",+        "type": "bidirectional",+        "description": "GPIO port C bit 14, main function after first backup domain power-up; alternate function OSC32_IN (32.768 kHz RTC crystal input); supplied through the backup power switch (3 mA max, 2 MHz max output speed)."+      },+      {+        "number": "4",+        "name": "PC15-OSC32_OUT",+        "type": "bidirectional",+        "description": "GPIO port C bit 15, main function after first backup domain power-up; alternate function OSC32_OUT (32.768 kHz RTC crystal output); supplied through the backup power switch (3 mA max, 2 MHz max output speed)."+      },+      {+        "number": "5",+        "name": "OSC_IN",+        "type": "input",+        "description": "Input of the 4-16 MHz high-speed external (HSE) crystal/ceramic resonator oscillator; can be remapped by software to GPIO PD0 (limited to 50 MHz in output mode)."+      },+      {+        "number": "6",+        "name": "OSC_OUT",+        "type": "output",+        "description": "Output of the 4-16 MHz high-speed external (HSE) crystal/ceramic resonator oscillator; can be remapped by software to GPIO PD1 (limited to 50 MHz in output mode)."+      },+      {+        "number": "7",+        "name": "NRST",+        "type": "bidirectional",+        "description": "Active-low system reset input/output with a permanent internal pull-up resistor (RPU) to VDD; a low level on this pin generates a device reset."+      },+      {+        "number": "8",+        "name": "VSSA",+        "type": "power_in",+        "description": "Analog ground supply for the ADC, reset blocks, RC oscillators and PLL; must be connected to VSS."+      },+      {+        "number": "9",+        "name": "VDDA",+        "type": "power_in",+        "description": "External analog power supply for ADC, reset blocks, RC oscillators and PLL, 2.0 to 3.6 V (minimum 2.4 V when the ADC is used); must be connected to VDD."+      },+      {+        "number": "10",+        "name": "PA0-WKUP",+        "type": "bidirectional",+        "description": "GPIO port A bit 0, 5 V tolerant; alternate functions WKUP (standby wakeup), USART2_CTS, ADC12_IN0, TIM2_CH1_ETR."+      },+      {+        "number": "11",+        "name": "PA1",+        "type": "bidirectional",+        "description": "GPIO port A bit 1, 5 V tolerant; alternate functions USART2_RTS, ADC12_IN1, TIM2_CH2."+      },+      {+        "number": "12",+        "name": "PA2",+        "type": "bidirectional",+        "description": "GPIO port A bit 2, 5 V tolerant; alternate functions USART2_TX, ADC12_IN2, TIM2_CH3."+      },+      {+        "number": "13",+        "name": "PA3",+        "type": "bidirectional",+        "description": "GPIO port A bit 3, 5 V tolerant; alternate functions USART2_RX, ADC12_IN3, TIM2_CH4."+      },+      {+        "number": "14",+        "name": "PA4",+        "type": "bidirectional",+        "description": "GPIO port A bit 4, 5 V tolerant; alternate functions SPI1_NSS, USART2_CK, ADC12_IN4."+      },+      {+        "number": "15",+        "name": "PA5",+        "type": "bidirectional",+        "description": "GPIO port A bit 5, 5 V tolerant; alternate functions SPI1_SCK, ADC12_IN5."+      },+      {+        "number": "16",+        "name": "PA6",+        "type": "bidirectional",+        "description": "GPIO port A bit 6, 5 V tolerant; default alternate functions SPI1_MISO, ADC12_IN6, TIM3_CH1, remappable to TIM1_BKIN."+      },+      {+        "number": "17",+        "name": "PA7",+        "type": "bidirectional",+        "description": "GPIO port A bit 7, 5 V tolerant; default alternate functions SPI1_MOSI, ADC12_IN7, TIM3_CH2, remappable to TIM1_CH1N."+      },+      {+        "number": "18",+        "name": "PB0",+        "type": "bidirectional",+        "description": "GPIO port B bit 0, 5 V tolerant; default alternate functions ADC12_IN8, TIM3_CH3, remappable to TIM1_CH2N."+      },+      {+        "number": "19",+        "name": "PB1",+        "type": "bidirectional",+        "description": "GPIO port B bit 1, 5 V tolerant; default alternate functions ADC12_IN9, TIM3_CH4, remappable to TIM1_CH3N."+      },+      {+        "number": "20",+        "name": "PB2/BOOT1",+        "type": "bidirectional",+        "description": "GPIO port B bit 2, 5 V tolerant, shared with BOOT1; sampled together with BOOT0 at reset to select the boot mode (Flash, System memory or SRAM)."+      },+      {+        "number": "21",+        "name": "PB10",+        "type": "bidirectional",+        "description": "GPIO port B bit 10, 5 V tolerant; default alternate functions I2C2_SCL, USART3_TX, remappable to TIM2_CH3."+      },+      {+        "number": "22",+        "name": "PB11",+        "type": "bidirectional",+        "description": "GPIO port B bit 11, 5 V tolerant; default alternate functions I2C2_SDA, USART3_RX, remappable to TIM2_CH4."+      },+      {+        "number": "23",+        "name": "VSS_1",+        "type": "power_in",+        "description": "Digital ground supply pin."+      },+      {+        "number": "24",+        "name": "VDD_1",+        "type": "power_in",+        "description": "External digital power supply pin, 2.0 to 3.6 V, for I/Os and internal regulator."+      },+      {+        "number": "25",+        "name": "PB12",+        "type": "bidirectional",+        "description": "GPIO port B bit 12, 5 V tolerant; alternate functions SPI2_NSS, I2C2_SMBAl, USART3_CK, TIM1_BKIN."+      },+      {+        "number": "26",+        "name": "PB13",+        "type": "bidirectional",+        "description": "GPIO port B bit 13, 5 V tolerant; alternate functions SPI2_SCK, USART3_CTS, TIM1_CH1N."+      },+      {+        "number": "27",+        "name": "PB14",+        "type": "bidirectional",+        "description": "GPIO port B bit 14, 5 V tolerant; alternate functions SPI2_MISO, USART3_RTS, TIM1_CH2N."+      },+      {+        "number": "28",+        "name": "PB15",+        "type": "bidirectional",+        "description": "GPIO port B bit 15, 5 V tolerant; alternate functions SPI2_MOSI, TIM1_CH3N."+      },+      {+        "number": "29",+        "name": "PA8",+        "type": "bidirectional",+        "description": "GPIO port A bit 8, 5 V tolerant; alternate functions USART1_CK, TIM1_CH1, MCO."+      },+      {+        "number": "30",+        "name": "PA9",+        "type": "bidirectional",+        "description": "GPIO port A bit 9, 5 V tolerant; alternate functions USART1_TX, TIM1_CH2."+      },+      {+        "number": "31",+        "name": "PA10",+        "type": "bidirectional",+        "description": "GPIO port A bit 10, 5 V tolerant; alternate functions USART1_RX, TIM1_CH3."+      },+      {+        "number": "32",+        "name": "PA11",+        "type": "bidirectional",+        "description": "GPIO port A bit 11, 5 V tolerant; alternate functions USART1_CTS, CANRX, USBDM, TIM1_CH4."+      },+      {+        "number": "33",+        "name": "PA12",+        "type": "bidirectional",+        "description": "GPIO port A bit 12, 5 V tolerant; alternate functions USART1_RTS, CANTX, USBDP, TIM1_ETR."+      },+      {+        "number": "34",+        "name": "PA13",+        "type": "bidirectional",+        "description": "GPIO port A bit 13, 5 V tolerant; default function JTMS/SWDIO debug interface pin."+      },+      {+        "number": "35",+        "name": "VSS_2",+        "type": "power_in",+        "description": "Digital ground supply pin."+      },+      {+        "number": "36",+        "name": "VDD_2",+        "type": "power_in",+        "description": "External digital power supply pin, 2.0 to 3.6 V, for I/Os and internal regulator."+      },+      {+        "number": "37",+        "name": "PA14",+        "type": "bidirectional",+        "description": "GPIO port A bit 14, 5 V tolerant; default function JTCK/SWCLK debug interface pin."+      },+      {+        "number": "38",+        "name": "PA15",+        "type": "bidirectional",+        "description": "GPIO port A bit 15, 5 V tolerant; default function JTDI, remappable to TIM2_CH1_ETR/SPI1_NSS."+      },+      {+        "number": "39",+        "name": "PB3",+        "type": "bidirectional",+        "description": "GPIO port B bit 3, 5 V tolerant; default function JTDO, remappable to TIM2_CH2/TRACESWO/SPI1_SCK."+      },+      {+        "number": "40",+        "name": "PB4",+        "type": "bidirectional",+        "description": "GPIO port B bit 4, 5 V tolerant; default function JNTRST, remappable to TIM3_CH1/SPI1_MISO."+      },+      {+        "number": "41",+        "name": "PB5",+        "type": "bidirectional",+        "description": "GPIO port B bit 5 (standard, not 5 V tolerant); default alternate function I2C1_SMBAl, remappable to TIM3_CH2/SPI1_MOSI."+      },+      {+        "number": "42",+        "name": "PB6",+        "type": "bidirectional",+        "description": "GPIO port B bit 6, 5 V tolerant; default alternate functions I2C1_SCL, TIM4_CH1, remappable to USART1_TX."+      },+      {+        "number": "43",+        "name": "PB7",+        "type": "bidirectional",+        "description": "GPIO port B bit 7, 5 V tolerant; default alternate functions I2C1_SDA, TIM4_CH2, remappable to USART1_RX."+      },+      {+        "number": "44",+        "name": "BOOT0",+        "type": "input",+        "description": "Boot mode selection pin, sampled together with BOOT1 (PB2) at reset to select boot from user Flash, system memory or embedded SRAM."+      },+      {+        "number": "45",+        "name": "PB8",+        "type": "bidirectional",+        "description": "GPIO port B bit 8, 5 V tolerant; default alternate function TIM4_CH3, remappable to I2C1_SCL/CANRX."+      },+      {+        "number": "46",+        "name": "PB9",+        "type": "bidirectional",+        "description": "GPIO port B bit 9, 5 V tolerant; default alternate function TIM4_CH4, remappable to I2C1_SDA/CANTX."+      },+      {+        "number": "47",+        "name": "VSS_3",+        "type": "power_in",+        "description": "Digital ground supply pin."+      },+      {+        "number": "48",+        "name": "VDD_3",+        "type": "power_in",+        "description": "External digital power supply pin, 2.0 to 3.6 V, for I/Os and internal regulator; the 4.7 µF decoupling capacitor must be connected to this VDD3 pin."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: PC13, PC14, PC15 pins have limited current capability (3 mA max) due to power switch design; they sh; Pins PD0 and PD1 are configured as oscillator pins (OSC_IN/OSC_OUT) after reset but can be remapped ; Multiple pins (PA13, PA14, PA15, PB3, PB4) serve dual purpose as JTAG/SWD debug interface pins and G"+        ],+        "pages_sent": 117,+        "cost_usd": 1.1285,+        "at": "2026-09-24T01:51:18"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590903672543133697",+        "pages": 117,+        "sha256": "4741c03c5793745c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 48,+        "described": 48,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file