Generated by kicad-footprint-generator · KiCad file format 20260206
STM32F101CBT6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32F101CBT6 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup power supply for the RTC and backup registers, as stated in the VBAT supply feature. |
| 2 | PC13-TAMPER-RTC | bidirectional | GPIO PC13 supplied through the power switch, which sinks only 3 mA; output speed must not exceed 2 MHz at 30 pF and it must not source current such as an LED drive. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO PC14 supplied through the power switch (3 mA limit), also the 32 kHz oscillator input OSC32_IN; output use limited to 2 MHz at 30 pF. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO PC15 supplied through the power switch (3 mA limit), also the 32 kHz oscillator output OSC32_OUT; output use limited to 2 MHz at 30 pF. |
| 5 | OSC_IN | input | High-speed external oscillator input (4-16 MHz crystal); configured as OSC_IN after reset and remappable to PD0. |
| 6 | OSC_OUT | output | High-speed external oscillator output (4-16 MHz crystal); configured as OSC_OUT after reset and remappable to PD1. |
| 7 | NRST | bidirectional | Active-low reset pin with no alternate function listed in Table 4. |
| 8 | VSSA | power_in | Analog ground reference for the ADC and analog circuitry. |
| 9 | VDDA | power_in | Analog supply for the ADC and analog circuitry, with a 2.0 to 3.6 V application supply range. |
| 10 | PA0-WKUP | bidirectional | 5 V tolerant GPIO PA0 with WKUP, USART2_CTS, ADC_IN0 and TIM2_CH1_ETR alternate functions. |
| 11 | PA1 | bidirectional | GPIO PA1 with USART2_RTS, ADC_IN1 and TIM2_CH2 alternate functions. |
| 12 | PA2 | bidirectional | GPIO PA2 with USART2_TX, ADC_IN2 and TIM2_CH3 alternate functions. |
| 13 | PA3 | bidirectional | GPIO PA3 with USART2_RX, ADC_IN3 and TIM2_CH4 alternate functions. |
| 14 | PA4 | bidirectional | GPIO PA4 with SPI1_NSS, USART2_CK and ADC_IN4 alternate functions. |
| 15 | PA5 | bidirectional | GPIO PA5 with SPI1_SCK and ADC_IN5 alternate functions. |
| 16 | PA6 | bidirectional | GPIO PA6 with SPI1_MISO, ADC_IN6 and TIM3_CH1 alternate functions. |
| 17 | PA7 | bidirectional | GPIO PA7 with SPI1_MOSI, ADC_IN7 and TIM3_CH2 alternate functions. |
| 18 | PB0 | bidirectional | GPIO PB0 with ADC_IN8 and TIM3_CH3 alternate functions. |
| 19 | PB1 | bidirectional | GPIO PB1 with ADC_IN9 and TIM3_CH4 alternate functions. |
| 20 | PB2/BOOT1 | bidirectional | 5 V tolerant GPIO PB2 that also serves as the BOOT1 boot-mode pin. |
| 21 | PB10 | bidirectional | 5 V tolerant GPIO PB10 with I2C2_SCL, USART3_TX and TIM2_CH3 alternate functions. |
| 22 | PB11 | bidirectional | 5 V tolerant GPIO PB11 with I2C2_SDA, USART3_RX and TIM2_CH4 alternate functions. |
| 23 | VSS_1 | power_in | Digital ground supply pin 1. |
| 24 | VDD_1 | power_in | Digital supply pin 1, within the 2.0 to 3.6 V application supply range. |
| 25 | PB12 | bidirectional | 5 V tolerant GPIO PB12 with SPI2_NSS, I2C2_SMBA and USART3_CK alternate functions. |
| 26 | PB13 | bidirectional | 5 V tolerant GPIO PB13 with SPI2_SCK and USART3_CTS alternate functions. |
| 27 | PB14 | bidirectional | 5 V tolerant GPIO PB14 with SPI2_MISO and USART3_RTS alternate functions. |
| 28 | PB15 | bidirectional | 5 V tolerant GPIO PB15 with SPI2_MOSI alternate function. |
| 29 | PA8 | bidirectional | 5 V tolerant GPIO PA8 with USART1_CK and MCO alternate functions. |
| 30 | PA9 | bidirectional | 5 V tolerant GPIO PA9 with USART1_TX alternate function. |
| 31 | PA10 | bidirectional | 5 V tolerant GPIO PA10 with USART1_RX alternate function. |
| 32 | PA11 | bidirectional | 5 V tolerant GPIO PA11 with USART1_CTS alternate function. |
| 33 | PA12 | bidirectional | 5 V tolerant GPIO PA12 with USART1_RTS alternate function. |
| 34 | PA13 | bidirectional | 5 V tolerant GPIO PA13 that carries the JTMS-SWDIO debug function after reset. |
| 35 | VSS_2 | power_in | Digital ground supply pin 2. |
| 36 | VDD_2 | power_in | Digital supply pin 2, within the 2.0 to 3.6 V application supply range. |
| 37 | PA14 | bidirectional | 5 V tolerant GPIO PA14 that carries the JTCK-SWCLK debug function after reset. |
| 38 | PA15 | bidirectional | 5 V tolerant GPIO PA15 with JTDI, TIM2_CH1_ETR and SPI1_NSS alternate functions. |
| 39 | PB3 | bidirectional | 5 V tolerant GPIO PB3 with JTDO, TIM2_CH2, TRACESWO and SPI1_SCK alternate functions. |
| 40 | PB4 | bidirectional | 5 V tolerant GPIO PB4 with JNTRST, TIM3_CH1 and SPI1_MISO alternate functions. |
| 41 | PB5 | bidirectional | GPIO PB5 with I2C1_SMBAL, TIM3_CH2 and SPI1_MOSI alternate functions. |
| 42 | PB6 | bidirectional | 5 V tolerant GPIO PB6 with I2C1_SCL, TIM4_CH1 and USART1_TX alternate functions. |
| 43 | PB7 | bidirectional | 5 V tolerant GPIO PB7 with I2C1_SDA, TIM4_CH2 and USART1_RX alternate functions. |
| 44 | BOOT0 | input | Boot mode selection input (BOOT0) used at startup. |
| 45 | PB8 | bidirectional | 5 V tolerant GPIO PB8 with TIM4_CH3 and I2C1_SCL alternate functions. |
| 46 | PB9 | bidirectional | 5 V tolerant GPIO PB9 with TIM4_CH4 and I2C1_SDA alternate functions. |
| 47 | VSS_3 | power_in | Digital ground supply pin 3. |
| 48 | VDD_3 | power_in | Digital supply pin 3, within the 2.0 to 3.6 V application supply range. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD | -0.3 | 4 | V | 32 | ||
| Input voltage on any other pin | VIN | -0.3 | 4 | V | 32 | ||
| Total current into VDD/VDDA power lines (source) | IVDD | 150 | mA | 33 | |||
| Total current out of VSS ground lines (sink) | IVSS | 150 | mA | 33 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 33 | |||
| Total injected current (sum of all I/O and control pins) | IINJ(PIN) | -25 | 25 | mA | 33 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 33 | ||
| Internal AHB clock frequency | fHCLK | 0 | 36 | MHz | 33 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | 33 | ||
| Analog operating voltage (ADC not used) | VDDA | 2 | 3.6 | V | Must be the same potential as VDD | 33 | |
| Analog operating voltage (ADC used) | VDDA | 2.4 | 3.6 | V | 33 | ||
| Backup operating voltage | VBAT | 1.8 | 3.6 | V | 33 | ||
| I/O FT input voltage | VIN | -0.3 | 5.5 | V | 2 V < VDD ≤ 3.6 V | 34 | |
| BOOT0 input voltage | VIN | 0 | 5.5 | V | BOOT0 | 34 | |
| Ambient temperature (maximum power dissipation) | TA | -40 | 85 | °C | Maximum power dissipation | 34 | |
| Ambient temperature (low power dissipation) | TA | -40 | 105 | °C | Low power dissipation | 34 | |
| Junction temperature range | TJ | -40 | 105 | °C | 34 | ||
| Power dissipation | PD | 363 | mW | Power dissipation at TA = 85 °C, LQFP48 | 34 | ||
| Power on/power down reset threshold (falling edge) | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 35 |
| Power on/power down reset threshold (rising edge) | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 35 |
| Programmable voltage detector level selection | VPVD | 2.76 | 2.88 | 3 | V | PLS[2:0]=111 (rising edge) | 35 |
| PVD hysteresis | VPVDhyst | 100 | mV | 35 | |||
| Reset temporization | tRSTTEMPO | 1.5 | 2.5 | 4.5 | ms | 35 | |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.24 | V | -40 °C < TA < +85 °C | 36 |
| Temperature coefficient | TCoeff | 100 | ppm/°C | 36 | |||
| Supply current in Run mode (code from Flash) | IDD | 28.6 | mA | External clock, all peripherals enabled, fHCLK 36 MHz, TA = 85 °C | 37 | ||
| Supply current in Run mode (code from Flash) | IDD | 8.6 | mA | External clock, all peripherals enabled, fHCLK 8 MHz, TA = 85 °C | 37 | ||
| Supply current in Run mode (code from Flash) | IDD | 19.8 | mA | External clock, all peripherals disabled, fHCLK 36 MHz, TA = 85 °C | 37 | ||
| Supply current in Run mode (code from RAM) | IDD | 24 | mA | External clock, all peripherals enabled, fHCLK 36 MHz, TA = 85 °C | 37 | ||
| Supply current in Sleep mode | IDD | 15.5 | mA | External clock, all peripherals enabled, fHCLK 36 MHz, TA = 85 °C | 39 | ||
| Supply current in Sleep mode | IDD | 5 | mA | External clock, all peripherals disabled, fHCLK 36 MHz, TA = 85 °C | 39 | ||
| Supply current in Stop mode | IDD | 200 | µA | Regulator in Run mode, LSI/HSI/HSE OFF (no independent watchdog), TA = 85 °C | 39 | ||
| Supply current in Stop mode | IDD | 180 | µA | Regulator in Low-Power mode, LSI/HSI/HSE OFF (no independent watchdog), TA = 85 °C | 39 | ||
| Supply current in Standby mode | IDD | 4 | µA | LSI OFF, independent watchdog OFF, LSE and RTC OFF, TA = 85 °C | 39 | ||
| Backup domain supply current | IDD_VBAT | 1.9 | µA | Low-speed oscillator and RTC ON, TA = 85 °C | 39 | ||
| User external clock source frequency | fHSE_ext | 1 | 8 | 25 | MHz | 45 | |
| Duty cycle (HSE external clock) | DuCy(HSE) | 45 | 55 | % | 45 | ||
| Oscillator frequency (HSE) | fOSC_IN | 4 | 8 | 16 | MHz | 47 | |
| Startup time (HSE) | tSU(HSE) | 2 | ms | VDD is stabilized | 47 | ||
| LSE driving current | I2 | 1.4 | µA | VDD = 3.3 V, VIN = VSS | 48 | ||
| Duty cycle (HSI) | DuCy(HSI) | 45 | 55 | % | 49 | ||
| Accuracy of the HSI oscillator (user-trimmed) | ACCHSI | -1 | 1 | % | User-trimmed with the RCC_CR register | 49 | |
| Accuracy of the HSI oscillator (factory-calibrated) | ACCHSI | -2 | 2.5 | % | TA = -40 to 105 °C | 49 | |
| Frequency (LSI) | fLSI | 30 | 40 | 60 | kHz | VDD = 3 V, TA = -40 to 85 °C | 50 |
| LSI oscillator startup time | tsu(LSI) | 85 | µs | 50 | |||
| LSI oscillator power consumption | IDD(LSI) | 0.65 | 1.2 | µA | VDD = 3 V, TA = -40 to 85 °C | 50 | |
| PLL input clock | fPLL_IN | 1 | 8 | 25 | MHz | 50 | |
| PLL input clock duty cycle | 40 | 60 | % | 50 | |||
| PLL multiplier output clock | fPLL_OUT | 16 | 36 | MHz | 50 | ||
| PLL lock time | tLOCK | 200 | µs | 50 | |||
| Cycle-to-cycle jitter (PLL) | Jitter | 300 | ps | Cycle-to-cycle jitter | 50 | ||
| 16-bit programming time | tprog | 40 | 52.5 | 70 | µs | TA -40 to +85 °C | 51 |
| Page (1 KB) erase time | tERASE | 20 | 40 | ms | TA -40 to +85 °C | 51 | |
| Mass erase time | tME | 20 | 40 | ms | TA -40 to +85 °C | 51 | |
| Supply current Flash read mode | IDD | 20 | mA | fHCLK = 36 MHz with 1 wait state, VDD = 3.3 V | 51 | ||
| Supply current Flash write/erase modes | IDD | 5 | mA | fHCLK = 36 MHz, VDD = 3.3 V | 51 | ||
| Supply current Flash power-down mode / Halt | IDD | 50 | µA | VDD = 3.0 to 3.6 V | 51 | ||
| Programming voltage | Vprog | 2 | 3.6 | V | 51 | ||
| Output low level voltage for an I/O pin (CMOS port) | VOL | 0.4 | V | IIO = +8 mA, 2.7 V < VDD < 3.6 V | 58 | ||
| NRST weak pull-up equivalent resistor | RPU | 30 | 40 | 50 | kΩ | VIN ≥ VSS | 60 |
CAD (KiCad official)
- Symbol:
STM32F101CBT6 - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32f101cbt6-etched.step/stm32f101cbt6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f101cbt6.step/stm32f101cbt6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (101 pp, sha256
860032e75b7a7da1, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).