Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32F101CBT6

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)

STM32F101CBT6 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup power supply for the RTC and backup registers, as stated in the VBAT supply feature.
2 PC13-TAMPER-RTC bidirectional GPIO PC13 supplied through the power switch, which sinks only 3 mA; output speed must not exceed 2 MHz at 30 pF and it must not source current such as an LED drive.
3 PC14-OSC32_IN bidirectional GPIO PC14 supplied through the power switch (3 mA limit), also the 32 kHz oscillator input OSC32_IN; output use limited to 2 MHz at 30 pF.
4 PC15-OSC32_OUT bidirectional GPIO PC15 supplied through the power switch (3 mA limit), also the 32 kHz oscillator output OSC32_OUT; output use limited to 2 MHz at 30 pF.
5 OSC_IN input High-speed external oscillator input (4-16 MHz crystal); configured as OSC_IN after reset and remappable to PD0.
6 OSC_OUT output High-speed external oscillator output (4-16 MHz crystal); configured as OSC_OUT after reset and remappable to PD1.
7 NRST bidirectional Active-low reset pin with no alternate function listed in Table 4.
8 VSSA power_in Analog ground reference for the ADC and analog circuitry.
9 VDDA power_in Analog supply for the ADC and analog circuitry, with a 2.0 to 3.6 V application supply range.
10 PA0-WKUP bidirectional 5 V tolerant GPIO PA0 with WKUP, USART2_CTS, ADC_IN0 and TIM2_CH1_ETR alternate functions.
11 PA1 bidirectional GPIO PA1 with USART2_RTS, ADC_IN1 and TIM2_CH2 alternate functions.
12 PA2 bidirectional GPIO PA2 with USART2_TX, ADC_IN2 and TIM2_CH3 alternate functions.
13 PA3 bidirectional GPIO PA3 with USART2_RX, ADC_IN3 and TIM2_CH4 alternate functions.
14 PA4 bidirectional GPIO PA4 with SPI1_NSS, USART2_CK and ADC_IN4 alternate functions.
15 PA5 bidirectional GPIO PA5 with SPI1_SCK and ADC_IN5 alternate functions.
16 PA6 bidirectional GPIO PA6 with SPI1_MISO, ADC_IN6 and TIM3_CH1 alternate functions.
17 PA7 bidirectional GPIO PA7 with SPI1_MOSI, ADC_IN7 and TIM3_CH2 alternate functions.
18 PB0 bidirectional GPIO PB0 with ADC_IN8 and TIM3_CH3 alternate functions.
19 PB1 bidirectional GPIO PB1 with ADC_IN9 and TIM3_CH4 alternate functions.
20 PB2/BOOT1 bidirectional 5 V tolerant GPIO PB2 that also serves as the BOOT1 boot-mode pin.
21 PB10 bidirectional 5 V tolerant GPIO PB10 with I2C2_SCL, USART3_TX and TIM2_CH3 alternate functions.
22 PB11 bidirectional 5 V tolerant GPIO PB11 with I2C2_SDA, USART3_RX and TIM2_CH4 alternate functions.
23 VSS_1 power_in Digital ground supply pin 1.
24 VDD_1 power_in Digital supply pin 1, within the 2.0 to 3.6 V application supply range.
25 PB12 bidirectional 5 V tolerant GPIO PB12 with SPI2_NSS, I2C2_SMBA and USART3_CK alternate functions.
26 PB13 bidirectional 5 V tolerant GPIO PB13 with SPI2_SCK and USART3_CTS alternate functions.
27 PB14 bidirectional 5 V tolerant GPIO PB14 with SPI2_MISO and USART3_RTS alternate functions.
28 PB15 bidirectional 5 V tolerant GPIO PB15 with SPI2_MOSI alternate function.
29 PA8 bidirectional 5 V tolerant GPIO PA8 with USART1_CK and MCO alternate functions.
30 PA9 bidirectional 5 V tolerant GPIO PA9 with USART1_TX alternate function.
31 PA10 bidirectional 5 V tolerant GPIO PA10 with USART1_RX alternate function.
32 PA11 bidirectional 5 V tolerant GPIO PA11 with USART1_CTS alternate function.
33 PA12 bidirectional 5 V tolerant GPIO PA12 with USART1_RTS alternate function.
34 PA13 bidirectional 5 V tolerant GPIO PA13 that carries the JTMS-SWDIO debug function after reset.
35 VSS_2 power_in Digital ground supply pin 2.
36 VDD_2 power_in Digital supply pin 2, within the 2.0 to 3.6 V application supply range.
37 PA14 bidirectional 5 V tolerant GPIO PA14 that carries the JTCK-SWCLK debug function after reset.
38 PA15 bidirectional 5 V tolerant GPIO PA15 with JTDI, TIM2_CH1_ETR and SPI1_NSS alternate functions.
39 PB3 bidirectional 5 V tolerant GPIO PB3 with JTDO, TIM2_CH2, TRACESWO and SPI1_SCK alternate functions.
40 PB4 bidirectional 5 V tolerant GPIO PB4 with JNTRST, TIM3_CH1 and SPI1_MISO alternate functions.
41 PB5 bidirectional GPIO PB5 with I2C1_SMBAL, TIM3_CH2 and SPI1_MOSI alternate functions.
42 PB6 bidirectional 5 V tolerant GPIO PB6 with I2C1_SCL, TIM4_CH1 and USART1_TX alternate functions.
43 PB7 bidirectional 5 V tolerant GPIO PB7 with I2C1_SDA, TIM4_CH2 and USART1_RX alternate functions.
44 BOOT0 input Boot mode selection input (BOOT0) used at startup.
45 PB8 bidirectional 5 V tolerant GPIO PB8 with TIM4_CH3 and I2C1_SCL alternate functions.
46 PB9 bidirectional 5 V tolerant GPIO PB9 with TIM4_CH4 and I2C1_SDA alternate functions.
47 VSS_3 power_in Digital ground supply pin 3.
48 VDD_3 power_in Digital supply pin 3, within the 2.0 to 3.6 V application supply range.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LQFP-48(7x7)
Category Embedded Processors & Controllers
Pins 48

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (including VDDA and VDD) VDD -0.3 4 V 32
Input voltage on any other pin VIN -0.3 4 V 32
Total current into VDD/VDDA power lines (source) IVDD 150 mA 33
Total current out of VSS ground lines (sink) IVSS 150 mA 33
Output current sunk by any I/O and control pin IIO 25 mA 33
Total injected current (sum of all I/O and control pins) IINJ(PIN) -25 25 mA 33
Storage temperature range TSTG -65 150 °C 33
Internal AHB clock frequency fHCLK 0 36 MHz 33
Standard operating voltage VDD 2 3.6 V 33
Analog operating voltage (ADC not used) VDDA 2 3.6 V Must be the same potential as VDD 33
Analog operating voltage (ADC used) VDDA 2.4 3.6 V 33
Backup operating voltage VBAT 1.8 3.6 V 33
I/O FT input voltage VIN -0.3 5.5 V 2 V < VDD ≤ 3.6 V 34
BOOT0 input voltage VIN 0 5.5 V BOOT0 34
Ambient temperature (maximum power dissipation) TA -40 85 °C Maximum power dissipation 34
Ambient temperature (low power dissipation) TA -40 105 °C Low power dissipation 34
Junction temperature range TJ -40 105 °C 34
Power dissipation PD 363 mW Power dissipation at TA = 85 °C, LQFP48 34
Power on/power down reset threshold (falling edge) VPOR/PDR 1.8 1.88 1.96 V Falling edge 35
Power on/power down reset threshold (rising edge) VPOR/PDR 1.84 1.92 2 V Rising edge 35
Programmable voltage detector level selection VPVD 2.76 2.88 3 V PLS[2:0]=111 (rising edge) 35
PVD hysteresis VPVDhyst 100 mV 35
Reset temporization tRSTTEMPO 1.5 2.5 4.5 ms 35
Internal reference voltage VREFINT 1.16 1.2 1.24 V -40 °C < TA < +85 °C 36
Temperature coefficient TCoeff 100 ppm/°C 36
Supply current in Run mode (code from Flash) IDD 28.6 mA External clock, all peripherals enabled, fHCLK 36 MHz, TA = 85 °C 37
Supply current in Run mode (code from Flash) IDD 8.6 mA External clock, all peripherals enabled, fHCLK 8 MHz, TA = 85 °C 37
Supply current in Run mode (code from Flash) IDD 19.8 mA External clock, all peripherals disabled, fHCLK 36 MHz, TA = 85 °C 37
Supply current in Run mode (code from RAM) IDD 24 mA External clock, all peripherals enabled, fHCLK 36 MHz, TA = 85 °C 37
Supply current in Sleep mode IDD 15.5 mA External clock, all peripherals enabled, fHCLK 36 MHz, TA = 85 °C 39
Supply current in Sleep mode IDD 5 mA External clock, all peripherals disabled, fHCLK 36 MHz, TA = 85 °C 39
Supply current in Stop mode IDD 200 µA Regulator in Run mode, LSI/HSI/HSE OFF (no independent watchdog), TA = 85 °C 39
Supply current in Stop mode IDD 180 µA Regulator in Low-Power mode, LSI/HSI/HSE OFF (no independent watchdog), TA = 85 °C 39
Supply current in Standby mode IDD 4 µA LSI OFF, independent watchdog OFF, LSE and RTC OFF, TA = 85 °C 39
Backup domain supply current IDD_VBAT 1.9 µA Low-speed oscillator and RTC ON, TA = 85 °C 39
User external clock source frequency fHSE_ext 1 8 25 MHz 45
Duty cycle (HSE external clock) DuCy(HSE) 45 55 % 45
Oscillator frequency (HSE) fOSC_IN 4 8 16 MHz 47
Startup time (HSE) tSU(HSE) 2 ms VDD is stabilized 47
LSE driving current I2 1.4 µA VDD = 3.3 V, VIN = VSS 48
Duty cycle (HSI) DuCy(HSI) 45 55 % 49
Accuracy of the HSI oscillator (user-trimmed) ACCHSI -1 1 % User-trimmed with the RCC_CR register 49
Accuracy of the HSI oscillator (factory-calibrated) ACCHSI -2 2.5 % TA = -40 to 105 °C 49
Frequency (LSI) fLSI 30 40 60 kHz VDD = 3 V, TA = -40 to 85 °C 50
LSI oscillator startup time tsu(LSI) 85 µs 50
LSI oscillator power consumption IDD(LSI) 0.65 1.2 µA VDD = 3 V, TA = -40 to 85 °C 50
PLL input clock fPLL_IN 1 8 25 MHz 50
PLL input clock duty cycle 40 60 % 50
PLL multiplier output clock fPLL_OUT 16 36 MHz 50
PLL lock time tLOCK 200 µs 50
Cycle-to-cycle jitter (PLL) Jitter 300 ps Cycle-to-cycle jitter 50
16-bit programming time tprog 40 52.5 70 µs TA -40 to +85 °C 51
Page (1 KB) erase time tERASE 20 40 ms TA -40 to +85 °C 51
Mass erase time tME 20 40 ms TA -40 to +85 °C 51
Supply current Flash read mode IDD 20 mA fHCLK = 36 MHz with 1 wait state, VDD = 3.3 V 51
Supply current Flash write/erase modes IDD 5 mA fHCLK = 36 MHz, VDD = 3.3 V 51
Supply current Flash power-down mode / Halt IDD 50 µA VDD = 3.0 to 3.6 V 51
Programming voltage Vprog 2 3.6 V 51
Output low level voltage for an I/O pin (CMOS port) VOL 0.4 V IIO = +8 mA, 2.7 V < VDD < 3.6 V 58
NRST weak pull-up equivalent resistor RPU 30 40 50 kΩ VIN ≥ VSS 60

CAD (KiCad official)

  • Symbol: STM32F101CBT6
  • Footprint: Package_QFP:LQFP-48_7x7mm_P0.5mm
  • 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
  • 3D model files: stm32f101cbt6-etched.step / stm32f101cbt6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32f101cbt6.step / stm32f101cbt6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (101 pp, sha256 860032e75b7a7da1, retrieved 2026-11-06, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF