Generated by kicad-footprint-generator · KiCad file format 20260206
STM32F100R8T7B
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
STM32F100R8T7B from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply for the RTC, the 32 kHz oscillator and backup registers when VDD is not present, with an operating range of 1.8 to 3.6 V. |
| 2 | PC13-TAMPER-RTC | bidirectional | General-purpose I/O (TAMPER-RTC alternate function) supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz with a 30 pF load and the pin must not be used as a current source. |
| 3 | PC14-OSC32_IN | bidirectional | General-purpose I/O on the backup domain that is also the 32.768 kHz LSE oscillator input (OSC32_IN), subject to the same 3 mA sink and 2 MHz / 30 pF output limits. |
| 4 | PC15-OSC32_OUT | bidirectional | General-purpose I/O on the backup domain that is also the LSE oscillator output (OSC32_OUT), subject to the same 3 mA sink and 2 MHz / 30 pF output limits. |
| 5 | OSC_IN | input | High-speed external oscillator input for a 4 to 24 MHz crystal or ceramic resonator; the functionality of PD0 can be remapped onto this pin by software. |
| 6 | OSC_OUT | output | High-speed external oscillator output for a 4 to 24 MHz crystal or ceramic resonator; the functionality of PD1 can be remapped onto this pin by software. |
| 7 | NRST | bidirectional | Active-low reset pin with an internal pull-up of 30 to 50 kΩ, where VIL(NRST) is at most 0.8 V, VIH(NRST) is at least 2 V, and pulses shorter than 100 ns are filtered. |
| 8 | PC0 | bidirectional | Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 10 (ADC1_IN10). |
| 9 | PC1 | bidirectional | Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 11 (ADC1_IN11). |
| 10 | PC2 | bidirectional | Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 12 (ADC1_IN12). |
| 11 | PC3 | bidirectional | Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 13 (ADC1_IN13). |
| 12 | VSSA | power_in | Analog ground for the ADC, DAC, reset blocks, RC oscillators and PLL; it must be connected to VSS. |
| 13 | VDDA | power_in | Analog supply for the ADC, DAC, reset blocks, RC oscillators and PLL, 2.0 to 3.6 V, which must be connected to VDD with a minimum of 2.4 V when the ADC or DAC is used. |
| 14 | PA0-WKUP | bidirectional | Standard GPIO with the WKUP function (a rising edge on this pin exits Standby mode) and the ADC1_IN0, USART2_CTS and TIM2_CH1_ETR alternate functions. |
| 15 | PA1 | bidirectional | Standard GPIO with the ADC1_IN1, USART2_RTS and TIM2_CH2 alternate functions. |
| 16 | PA2 | bidirectional | Standard GPIO with the ADC1_IN2, USART2_TX, TIM2_CH3 and TIM15_CH1 alternate functions. |
| 17 | PA3 | bidirectional | Standard GPIO with the ADC1_IN3, USART2_RX, TIM2_CH4 and TIM15_CH2 alternate functions. |
| 18 | VSS_4 | power_in | Digital ground pin that must be connected to the common ground (VSS). |
| 19 | VDD_4 | power_in | Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V. |
| 20 | PA4 | bidirectional | Standard GPIO with the SPI1_NSS, ADC1_IN4, USART2_CK and DAC1_OUT alternate functions. |
| 21 | PA5 | bidirectional | Standard GPIO with the SPI1_SCK, ADC1_IN5 and DAC2_OUT alternate functions. |
| 22 | PA6 | bidirectional | Standard GPIO with the SPI1_MISO, ADC1_IN6 and TIM3_CH1 alternate functions (TIM1_BKIN and TIM16_CH1 on remap). |
| 23 | PA7 | bidirectional | Standard GPIO with the SPI1_MOSI, ADC1_IN7 and TIM3_CH2 alternate functions (TIM1_CH1N and TIM17_CH1 on remap). |
| 24 | PC4 | bidirectional | Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 14 (ADC1_IN14). |
| 25 | PC5 | bidirectional | Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 15 (ADC1_IN15). |
| 26 | PB0 | bidirectional | Standard GPIO with the ADC1_IN8 and TIM3_CH3 alternate functions (TIM1_CH2N on remap). |
| 27 | PB1 | bidirectional | Standard GPIO with the ADC1_IN9 and TIM3_CH4 alternate functions (TIM1_CH3N on remap). |
| 28 | PB2 | bidirectional | 5 V-tolerant (FT) GPIO that also carries the BOOT1 boot-mode function. |
| 29 | PB10 | bidirectional | 5 V-tolerant (FT) GPIO with I2C2_SCL and USART3_TX as default alternate functions (TIM2_CH3 and HDMI_CEC on remap). |
| 30 | PB11 | bidirectional | 5 V-tolerant (FT) GPIO with I2C2_SDA and USART3_RX as default alternate functions (TIM2_CH4 on remap is not stated; TIM2_CH4 listed in main alternate functions). |
| 31 | VSS_1 | power_in | Digital ground pin that must be connected to the common ground (VSS). |
| 32 | VDD_1 | power_in | Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V. |
| 33 | PB12 | bidirectional | 5 V-tolerant (FT) GPIO with the SPI2_NSS, I2C2_SMBA, TIM1_BKIN and USART3_CK alternate functions. |
| 34 | PB13 | bidirectional | 5 V-tolerant (FT) GPIO with the SPI2_SCK, TIM1_CH1N and USART3_CTS alternate functions. |
| 35 | PB14 | bidirectional | 5 V-tolerant (FT) GPIO with the SPI2_MISO, TIM1_CH2N and USART3_RTS alternate functions (TIM15_CH1 on remap). |
| 36 | PB15 | bidirectional | 5 V-tolerant (FT) GPIO with the SPI2_MOSI, TIM1_CH3N and TIM15_CH1N alternate functions (TIM15_CH2 on remap). |
| 37 | PC6 | bidirectional | 5 V-tolerant (FT) GPIO with the TIM3_CH1 alternate function. |
| 38 | PC7 | bidirectional | 5 V-tolerant (FT) GPIO with the TIM3_CH2 alternate function. |
| 39 | PC8 | bidirectional | 5 V-tolerant (FT) GPIO with the TIM3_CH3 alternate function. |
| 40 | PC9 | bidirectional | 5 V-tolerant (FT) GPIO with the TIM3_CH4 alternate function. |
| 41 | PA8 | bidirectional | 5 V-tolerant (FT) GPIO with the USART1_CK, MCO and TIM1_CH1 alternate functions. |
| 42 | PA9 | bidirectional | 5 V-tolerant (FT) GPIO with the USART1_TX, TIM1_CH2 and TIM15_BKIN alternate functions. |
| 43 | PA10 | bidirectional | 5 V-tolerant (FT) GPIO with the USART1_RX, TIM1_CH3 and TIM17_BKIN alternate functions. |
| 44 | PA11 | bidirectional | 5 V-tolerant (FT) GPIO with the USART1_CTS and TIM1_CH4 alternate functions. |
| 45 | PA12 | bidirectional | 5 V-tolerant (FT) GPIO with the USART1_RTS and TIM1_ETR alternate functions. |
| 46 | PA13 | bidirectional | 5 V-tolerant (FT) GPIO that after reset is used as the JTMS-SWDIO serial wire debug pin. |
| 47 | VSS_2 | power_in | Digital ground pin that must be connected to the common ground (VSS). |
| 48 | VDD_2 | power_in | Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V. |
| 49 | PA14 | bidirectional | 5 V-tolerant (FT) GPIO that after reset is used as the JTCK-SWCLK serial wire debug pin. |
| 50 | PA15 | bidirectional | 5 V-tolerant (FT) GPIO that after reset is used as JTDI; TIM2_CH1_ETR and SPI1_NSS are available on remap. |
| 51 | PC10 | bidirectional | 5 V-tolerant (FT) GPIO with USART3_TX available on remap. |
| 52 | PC11 | bidirectional | 5 V-tolerant (FT) GPIO with USART3_RX available on remap. |
| 53 | PC12 | bidirectional | 5 V-tolerant (FT) GPIO with USART3_CK available on remap. |
| 54 | PD2 | bidirectional | 5 V-tolerant (FT) GPIO with the TIM3_ETR alternate function. |
| 55 | PB3 | bidirectional | 5 V-tolerant (FT) GPIO that after reset is used as JTDO; TIM2_CH2 and PB3 are the default alternate functions, with TRACESWO and SPI1_SCK on remap. |
| 56 | PB4 | bidirectional | 5 V-tolerant (FT) GPIO that after reset is used as NJTRST, with TIM3_CH1 and SPI1_MISO alternate functions. |
| 57 | PB5 | bidirectional | Standard (non-5 V-tolerant) GPIO with the I2C1_SMBA and TIM16_BKIN alternate functions (TIM3_CH2 and SPI1_MOSI on remap). |
| 58 | PB6 | bidirectional | 5 V-tolerant (FT) GPIO with the I2C1_SCL and TIM4_CH1 alternate functions (TIM16_CH1N and USART1_TX on remap). |
| 59 | PB7 | bidirectional | 5 V-tolerant (FT) GPIO with the I2C1_SDA and TIM17_CH1N alternate functions (TIM4_CH2 and USART1_RX on remap). |
| 60 | BOOT0 | input | Boot-mode selection input that selects the boot source (user Flash, system memory or embedded SRAM) at startup. |
| 61 | PB8 | bidirectional | 5 V-tolerant (FT) GPIO with the TIM4_CH3, TIM16_CH1 and CEC alternate functions (I2C1_SCL on remap). |
| 62 | PB9 | bidirectional | 5 V-tolerant (FT) GPIO with the TIM4_CH4 and TIM17_CH1 alternate functions (I2C1_SDA on remap). |
| 63 | VSS_3 | power_in | Digital ground pin that must be connected to the common ground (VSS). |
| 64 | VDD_3 | power_in | Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD − VSS | -0.3 | 4 | V | 33 | ||
| Input voltage on any other pin | VIN | 4 | V | 33 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 33 | |||
| Variations between all the different ground pins | /VSSX − VSS/ | 50 | mV | 33 | |||
| Total current into VDD/VDDA power lines (source) | IVDD | 150 | mA | 34 | |||
| Total current out of VSS ground lines (sink) | IVSS | 150 | mA | 34 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 34 | |||
| Output current source by any I/Os and control pin | IIO | -25 | mA | 34 | |||
| Injected current on five volt tolerant pins | IINJ(PIN) | -5 | 0 | mA | 34 | ||
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | 34 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 34 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 34 | ||
| Maximum junction temperature | TJ | 150 | °C | 34 | |||
| Internal AHB clock frequency | fHCLK | 0 | 24 | MHz | 34 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 24 | MHz | 34 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 24 | MHz | 34 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | 34 | ||
| Analog operating voltage (ADC not used) | VDDA | 2 | 3.6 | V | Must be the same potential as VDD | 34 | |
| Analog operating voltage (ADC used) | VDDA | 2.4 | 3.6 | V | ADC used | 34 | |
| Backup operating voltage | VBAT | 1.8 | 3.6 | V | 34 | ||
| Ambient temperature for 7 suffix version (maximum power dissipation) | TA | -40 | 105 | °C | Maximum power dissipation | 35 | |
| Ambient temperature for 7 suffix version (low power dissipation) | TA | -40 | 125 | °C | Low power dissipation | 35 | |
| Junction temperature range, 7 suffix version | TJ | -40 | 125 | °C | 7 suffix version | 35 | |
| Power dissipation LQFP64 | PD | 444 | mW | TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 | 35 | ||
| VDD rise time rate | tVDD | 0 | µs/V | 35 | |||
| VDD fall time rate | tVDD | 20 | µs/V | 35 | |||
| Power on/power down reset threshold (falling edge) | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 36 |
| Power on/power down reset threshold (rising edge) | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 36 |
| Reset temporization | tRSTTEMPO | 1.5 | 2.5 | 4.5 | ms | 36 | |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.26 | V | -40 °C < TA < +105 °C | 37 |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.24 | V | -40 °C < TA < +85 °C | 37 |
| ADC sampling time when reading the internal reference voltage | TS_vrefint | 5.1 | 17.1 | µs | 37 | ||
| Internal reference voltage spread over the temperature range | VRERINT | 10 | mV | VDD = 3 V | 37 | ||
| Temperature coefficient | TCoeff | 100 | ppm/°C | 37 | |||
| Supply current in Run mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 85 °C | IDD | 15.4 | mA | Code running from Flash; external clock, all peripherals enabled, 24 MHz, TA = 85 °C | 38 | ||
| Supply current in Run mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 105 °C | IDD | 15.7 | mA | Code running from Flash; external clock, all peripherals enabled, 24 MHz, TA = 105 °C | 38 | ||
| Supply current in Run mode, external clock, all peripherals disabled, fHCLK 24 MHz, TA = 85 °C | IDD | 10.3 | mA | Code running from Flash; external clock, all peripherals disabled, 24 MHz, TA = 85 °C | 38 | ||
| Supply current in Run mode, external clock, all peripherals disabled, fHCLK 24 MHz, TA = 105 °C | IDD | 10.5 | mA | Code running from Flash; external clock, all peripherals disabled, 24 MHz, TA = 105 °C | 38 | ||
| Supply current in Sleep mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 85 °C | IDD | 9.6 | mA | External clock, all peripherals enabled, 24 MHz, TA = 85 °C | 39 | ||
| Supply current in Sleep mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 105 °C | IDD | 10 | mA | External clock, all peripherals enabled, 24 MHz, TA = 105 °C | 39 | ||
| Supply current in Stop mode, regulator in Run mode, TA = 85 °C | IDD | 190 | µA | Regulator in Run mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog); TA = 85 °C | 40 | ||
| Supply current in Stop mode, regulator in Run mode, TA = 105 °C | IDD | 350 | µA | Regulator in Run mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog); TA = 105 °C | 40 | ||
| Supply current in Standby mode, TA = 85 °C | IDD | 4 | µA | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; TA = 85 °C | 40 | ||
| Supply current in Standby mode, TA = 105 °C | IDD | 5 | µA | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; TA = 105 °C | 40 | ||
| HSI oscillator accuracy | ACCHSI | -2.4 | 2.5 | % | TA = -40 to 105 °C | 50 | |
| HSI oscillator accuracy | ACCHSI | -2.2 | 1.3 | % | TA = -10 to 85 °C | 50 | |
| HSI oscillator accuracy | ACCHSI | -1.9 | 1.3 | % | TA = 0 to 70 °C | 50 | |
| HSI oscillator accuracy | ACCHSI | -1 | 1 | % | TA = 25 °C | 50 | |
| LSI oscillator frequency | fLSI | 30 | 40 | 60 | kHz | VDD = 3 V, TA = -40 to 105 °C | 51 |
| NRST input low level voltage | VIL(NRST) | -0.5 | 0.8 | V | 62 | ||
| NRST input high level voltage | VIH(NRST) | 2 | V | 62 | |||
| NRST input filtered pulse | VF(NRST) | 100 | ns | 62 | |||
| NRST weak pull-up equivalent resistor | RPU | 30 | 40 | 50 | kΩ | VIN = VSS | 62 |
| Standard I/O input leakage current | Ilkg | -1 | 1 | µA | VSS ≤ VIN ≤ VDD, standard I/Os | 57 | |
| 5 V tolerant I/O (FT) input leakage current | Ilkg | 3 | µA | VIN = 5 V | 57 | ||
| Weak pull-up equivalent resistor (I/O) | RPU | 30 | 40 | 50 | kΩ | VIN = VSS | 57 |
| Output low level voltage for an I/O pin, CMOS port | VOL | 0.4 | V | IIO = +8 mA, 2.7 V < VDD < 3.6 V | 60 | ||
| Output high level voltage for an I/O pin, TTL port | VOH | 2.4 | V | TTL port; 8 pins sourced at the same time | 60 | ||
| Output low level voltage for an I/O pin, TTL port | VOL | 0.4 | V | IIO = +8 mA, 2.7 V < VDD < 3.6 V | 60 | ||
| Output low level voltage for an I/O pin (relaxed VOL) | VOL | 1.3 | V | IIO = +20 mA, 2.7 V < VDD < 3.6 V | 60 |
CAD (KiCad official)
- Symbol:
STM32F100R8T7B - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32f100r8t7b-etched.step/stm32f100r8t7b-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f100r8t7b.step/stm32f100r8t7b.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (96 pp, sha256
360e3be010cabad4, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).