Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32F100R8T7B

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)

STM32F100R8T7B from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup-domain supply for the RTC, the 32 kHz oscillator and backup registers when VDD is not present, with an operating range of 1.8 to 3.6 V.
2 PC13-TAMPER-RTC bidirectional General-purpose I/O (TAMPER-RTC alternate function) supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz with a 30 pF load and the pin must not be used as a current source.
3 PC14-OSC32_IN bidirectional General-purpose I/O on the backup domain that is also the 32.768 kHz LSE oscillator input (OSC32_IN), subject to the same 3 mA sink and 2 MHz / 30 pF output limits.
4 PC15-OSC32_OUT bidirectional General-purpose I/O on the backup domain that is also the LSE oscillator output (OSC32_OUT), subject to the same 3 mA sink and 2 MHz / 30 pF output limits.
5 OSC_IN input High-speed external oscillator input for a 4 to 24 MHz crystal or ceramic resonator; the functionality of PD0 can be remapped onto this pin by software.
6 OSC_OUT output High-speed external oscillator output for a 4 to 24 MHz crystal or ceramic resonator; the functionality of PD1 can be remapped onto this pin by software.
7 NRST bidirectional Active-low reset pin with an internal pull-up of 30 to 50 kΩ, where VIL(NRST) is at most 0.8 V, VIH(NRST) is at least 2 V, and pulses shorter than 100 ns are filtered.
8 PC0 bidirectional Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 10 (ADC1_IN10).
9 PC1 bidirectional Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 11 (ADC1_IN11).
10 PC2 bidirectional Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 12 (ADC1_IN12).
11 PC3 bidirectional Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 13 (ADC1_IN13).
12 VSSA power_in Analog ground for the ADC, DAC, reset blocks, RC oscillators and PLL; it must be connected to VSS.
13 VDDA power_in Analog supply for the ADC, DAC, reset blocks, RC oscillators and PLL, 2.0 to 3.6 V, which must be connected to VDD with a minimum of 2.4 V when the ADC or DAC is used.
14 PA0-WKUP bidirectional Standard GPIO with the WKUP function (a rising edge on this pin exits Standby mode) and the ADC1_IN0, USART2_CTS and TIM2_CH1_ETR alternate functions.
15 PA1 bidirectional Standard GPIO with the ADC1_IN1, USART2_RTS and TIM2_CH2 alternate functions.
16 PA2 bidirectional Standard GPIO with the ADC1_IN2, USART2_TX, TIM2_CH3 and TIM15_CH1 alternate functions.
17 PA3 bidirectional Standard GPIO with the ADC1_IN3, USART2_RX, TIM2_CH4 and TIM15_CH2 alternate functions.
18 VSS_4 power_in Digital ground pin that must be connected to the common ground (VSS).
19 VDD_4 power_in Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V.
20 PA4 bidirectional Standard GPIO with the SPI1_NSS, ADC1_IN4, USART2_CK and DAC1_OUT alternate functions.
21 PA5 bidirectional Standard GPIO with the SPI1_SCK, ADC1_IN5 and DAC2_OUT alternate functions.
22 PA6 bidirectional Standard GPIO with the SPI1_MISO, ADC1_IN6 and TIM3_CH1 alternate functions (TIM1_BKIN and TIM16_CH1 on remap).
23 PA7 bidirectional Standard GPIO with the SPI1_MOSI, ADC1_IN7 and TIM3_CH2 alternate functions (TIM1_CH1N and TIM17_CH1 on remap).
24 PC4 bidirectional Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 14 (ADC1_IN14).
25 PC5 bidirectional Standard (non-5 V-tolerant) GPIO that can also be used as ADC1 analog input channel 15 (ADC1_IN15).
26 PB0 bidirectional Standard GPIO with the ADC1_IN8 and TIM3_CH3 alternate functions (TIM1_CH2N on remap).
27 PB1 bidirectional Standard GPIO with the ADC1_IN9 and TIM3_CH4 alternate functions (TIM1_CH3N on remap).
28 PB2 bidirectional 5 V-tolerant (FT) GPIO that also carries the BOOT1 boot-mode function.
29 PB10 bidirectional 5 V-tolerant (FT) GPIO with I2C2_SCL and USART3_TX as default alternate functions (TIM2_CH3 and HDMI_CEC on remap).
30 PB11 bidirectional 5 V-tolerant (FT) GPIO with I2C2_SDA and USART3_RX as default alternate functions (TIM2_CH4 on remap is not stated; TIM2_CH4 listed in main alternate functions).
31 VSS_1 power_in Digital ground pin that must be connected to the common ground (VSS).
32 VDD_1 power_in Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V.
33 PB12 bidirectional 5 V-tolerant (FT) GPIO with the SPI2_NSS, I2C2_SMBA, TIM1_BKIN and USART3_CK alternate functions.
34 PB13 bidirectional 5 V-tolerant (FT) GPIO with the SPI2_SCK, TIM1_CH1N and USART3_CTS alternate functions.
35 PB14 bidirectional 5 V-tolerant (FT) GPIO with the SPI2_MISO, TIM1_CH2N and USART3_RTS alternate functions (TIM15_CH1 on remap).
36 PB15 bidirectional 5 V-tolerant (FT) GPIO with the SPI2_MOSI, TIM1_CH3N and TIM15_CH1N alternate functions (TIM15_CH2 on remap).
37 PC6 bidirectional 5 V-tolerant (FT) GPIO with the TIM3_CH1 alternate function.
38 PC7 bidirectional 5 V-tolerant (FT) GPIO with the TIM3_CH2 alternate function.
39 PC8 bidirectional 5 V-tolerant (FT) GPIO with the TIM3_CH3 alternate function.
40 PC9 bidirectional 5 V-tolerant (FT) GPIO with the TIM3_CH4 alternate function.
41 PA8 bidirectional 5 V-tolerant (FT) GPIO with the USART1_CK, MCO and TIM1_CH1 alternate functions.
42 PA9 bidirectional 5 V-tolerant (FT) GPIO with the USART1_TX, TIM1_CH2 and TIM15_BKIN alternate functions.
43 PA10 bidirectional 5 V-tolerant (FT) GPIO with the USART1_RX, TIM1_CH3 and TIM17_BKIN alternate functions.
44 PA11 bidirectional 5 V-tolerant (FT) GPIO with the USART1_CTS and TIM1_CH4 alternate functions.
45 PA12 bidirectional 5 V-tolerant (FT) GPIO with the USART1_RTS and TIM1_ETR alternate functions.
46 PA13 bidirectional 5 V-tolerant (FT) GPIO that after reset is used as the JTMS-SWDIO serial wire debug pin.
47 VSS_2 power_in Digital ground pin that must be connected to the common ground (VSS).
48 VDD_2 power_in Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V.
49 PA14 bidirectional 5 V-tolerant (FT) GPIO that after reset is used as the JTCK-SWCLK serial wire debug pin.
50 PA15 bidirectional 5 V-tolerant (FT) GPIO that after reset is used as JTDI; TIM2_CH1_ETR and SPI1_NSS are available on remap.
51 PC10 bidirectional 5 V-tolerant (FT) GPIO with USART3_TX available on remap.
52 PC11 bidirectional 5 V-tolerant (FT) GPIO with USART3_RX available on remap.
53 PC12 bidirectional 5 V-tolerant (FT) GPIO with USART3_CK available on remap.
54 PD2 bidirectional 5 V-tolerant (FT) GPIO with the TIM3_ETR alternate function.
55 PB3 bidirectional 5 V-tolerant (FT) GPIO that after reset is used as JTDO; TIM2_CH2 and PB3 are the default alternate functions, with TRACESWO and SPI1_SCK on remap.
56 PB4 bidirectional 5 V-tolerant (FT) GPIO that after reset is used as NJTRST, with TIM3_CH1 and SPI1_MISO alternate functions.
57 PB5 bidirectional Standard (non-5 V-tolerant) GPIO with the I2C1_SMBA and TIM16_BKIN alternate functions (TIM3_CH2 and SPI1_MOSI on remap).
58 PB6 bidirectional 5 V-tolerant (FT) GPIO with the I2C1_SCL and TIM4_CH1 alternate functions (TIM16_CH1N and USART1_TX on remap).
59 PB7 bidirectional 5 V-tolerant (FT) GPIO with the I2C1_SDA and TIM17_CH1N alternate functions (TIM4_CH2 and USART1_RX on remap).
60 BOOT0 input Boot-mode selection input that selects the boot source (user Flash, system memory or embedded SRAM) at startup.
61 PB8 bidirectional 5 V-tolerant (FT) GPIO with the TIM4_CH3, TIM16_CH1 and CEC alternate functions (I2C1_SCL on remap).
62 PB9 bidirectional 5 V-tolerant (FT) GPIO with the TIM4_CH4 and TIM17_CH1 alternate functions (I2C1_SDA on remap).
63 VSS_3 power_in Digital ground pin that must be connected to the common ground (VSS).
64 VDD_3 power_in Digital supply pin for the I/Os and the internal regulator, 2.0 to 3.6 V.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LQFP-64(10x10)
Category Embedded Processors & Controllers
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (including VDDA and VDD) VDD − VSS -0.3 4 V 33
Input voltage on any other pin VIN 4 V 33
Variations between different VDD power pins /ΔVDDx/ 50 mV 33
Variations between all the different ground pins /VSSX − VSS/ 50 mV 33
Total current into VDD/VDDA power lines (source) IVDD 150 mA 34
Total current out of VSS ground lines (sink) IVSS 150 mA 34
Output current sunk by any I/O and control pin IIO 25 mA 34
Output current source by any I/Os and control pin IIO -25 mA 34
Injected current on five volt tolerant pins IINJ(PIN) -5 0 mA 34
Injected current on any other pin IINJ(PIN) -5 5 mA 34
Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) -25 25 mA 34
Storage temperature range TSTG -65 150 °C 34
Maximum junction temperature TJ 150 °C 34
Internal AHB clock frequency fHCLK 0 24 MHz 34
Internal APB1 clock frequency fPCLK1 0 24 MHz 34
Internal APB2 clock frequency fPCLK2 0 24 MHz 34
Standard operating voltage VDD 2 3.6 V 34
Analog operating voltage (ADC not used) VDDA 2 3.6 V Must be the same potential as VDD 34
Analog operating voltage (ADC used) VDDA 2.4 3.6 V ADC used 34
Backup operating voltage VBAT 1.8 3.6 V 34
Ambient temperature for 7 suffix version (maximum power dissipation) TA -40 105 °C Maximum power dissipation 35
Ambient temperature for 7 suffix version (low power dissipation) TA -40 125 °C Low power dissipation 35
Junction temperature range, 7 suffix version TJ -40 125 °C 7 suffix version 35
Power dissipation LQFP64 PD 444 mW TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 35
VDD rise time rate tVDD 0 µs/V 35
VDD fall time rate tVDD 20 µs/V 35
Power on/power down reset threshold (falling edge) VPOR/PDR 1.8 1.88 1.96 V Falling edge 36
Power on/power down reset threshold (rising edge) VPOR/PDR 1.84 1.92 2 V Rising edge 36
Reset temporization tRSTTEMPO 1.5 2.5 4.5 ms 36
Internal reference voltage VREFINT 1.16 1.2 1.26 V -40 °C < TA < +105 °C 37
Internal reference voltage VREFINT 1.16 1.2 1.24 V -40 °C < TA < +85 °C 37
ADC sampling time when reading the internal reference voltage TS_vrefint 5.1 17.1 µs 37
Internal reference voltage spread over the temperature range VRERINT 10 mV VDD = 3 V 37
Temperature coefficient TCoeff 100 ppm/°C 37
Supply current in Run mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 85 °C IDD 15.4 mA Code running from Flash; external clock, all peripherals enabled, 24 MHz, TA = 85 °C 38
Supply current in Run mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 105 °C IDD 15.7 mA Code running from Flash; external clock, all peripherals enabled, 24 MHz, TA = 105 °C 38
Supply current in Run mode, external clock, all peripherals disabled, fHCLK 24 MHz, TA = 85 °C IDD 10.3 mA Code running from Flash; external clock, all peripherals disabled, 24 MHz, TA = 85 °C 38
Supply current in Run mode, external clock, all peripherals disabled, fHCLK 24 MHz, TA = 105 °C IDD 10.5 mA Code running from Flash; external clock, all peripherals disabled, 24 MHz, TA = 105 °C 38
Supply current in Sleep mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 85 °C IDD 9.6 mA External clock, all peripherals enabled, 24 MHz, TA = 85 °C 39
Supply current in Sleep mode, external clock, all peripherals enabled, fHCLK 24 MHz, TA = 105 °C IDD 10 mA External clock, all peripherals enabled, 24 MHz, TA = 105 °C 39
Supply current in Stop mode, regulator in Run mode, TA = 85 °C IDD 190 µA Regulator in Run mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog); TA = 85 °C 40
Supply current in Stop mode, regulator in Run mode, TA = 105 °C IDD 350 µA Regulator in Run mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog); TA = 105 °C 40
Supply current in Standby mode, TA = 85 °C IDD 4 µA Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; TA = 85 °C 40
Supply current in Standby mode, TA = 105 °C IDD 5 µA Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; TA = 105 °C 40
HSI oscillator accuracy ACCHSI -2.4 2.5 % TA = -40 to 105 °C 50
HSI oscillator accuracy ACCHSI -2.2 1.3 % TA = -10 to 85 °C 50
HSI oscillator accuracy ACCHSI -1.9 1.3 % TA = 0 to 70 °C 50
HSI oscillator accuracy ACCHSI -1 1 % TA = 25 °C 50
LSI oscillator frequency fLSI 30 40 60 kHz VDD = 3 V, TA = -40 to 105 °C 51
NRST input low level voltage VIL(NRST) -0.5 0.8 V 62
NRST input high level voltage VIH(NRST) 2 V 62
NRST input filtered pulse VF(NRST) 100 ns 62
NRST weak pull-up equivalent resistor RPU 30 40 50 kΩ VIN = VSS 62
Standard I/O input leakage current Ilkg -1 1 µA VSS ≤ VIN ≤ VDD, standard I/Os 57
5 V tolerant I/O (FT) input leakage current Ilkg 3 µA VIN = 5 V 57
Weak pull-up equivalent resistor (I/O) RPU 30 40 50 kΩ VIN = VSS 57
Output low level voltage for an I/O pin, CMOS port VOL 0.4 V IIO = +8 mA, 2.7 V < VDD < 3.6 V 60
Output high level voltage for an I/O pin, TTL port VOH 2.4 V TTL port; 8 pins sourced at the same time 60
Output low level voltage for an I/O pin, TTL port VOL 0.4 V IIO = +8 mA, 2.7 V < VDD < 3.6 V 60
Output low level voltage for an I/O pin (relaxed VOL) VOL 1.3 V IIO = +20 mA, 2.7 V < VDD < 3.6 V 60

CAD (KiCad official)

  • Symbol: STM32F100R8T7B
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: stm32f100r8t7b-etched.step / stm32f100r8t7b-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32f100r8t7b.step / stm32f100r8t7b.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (96 pp, sha256 360e3be010cabad4, retrieved 2026-11-10, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF