3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM1061N28WX6F
STMicroelectronics · Supervisor And Reset ICs · SOT-23-3
STM1061N28WX6F from STMicroelectronics, in a SOT-23-3. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | output | Active-low open drain output that goes low when VCC drops below VTH- and stays low until VCC rises above VTH+ (VTH- + VHYST), so a pull-up resistor to any supply up to 6V is required. |
| 2 | VSS | power_in | Ground, the reference for the power supply, which must be connected to the system ground. |
| 3 | VCC | power_in | Supply voltage and input for the voltage detector, specified for 0.7 V to 6.0 V operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOT-23-3 |
| Category | Power Management (PMIC) |
| Pins | 3 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Operating Voltage | VCC | 0.7 | 6 | V | 16 | ||
| VCC Supply Voltage (Measurement Conditions) | VCC | 0.7 | 6 | V | 14 | ||
| Ambient Operating Temperature | TA | -40 | 85 | °C | 14 | ||
| Detect Voltage VTH- (suffix 28) | VTH- | 2.744 | 2.8 | 2.856 | V | TA = 25°C, suffix 28 (Table 9) | 21 |
| VCC Supply Current | ICC | 0.9 | 3 | µA | VCC = 3.0V, no load | 16 | |
| VCC Supply Current | ICC | 1.1 | 3.6 | µA | VCC = 5.5V, no load | 16 | |
| Output Current, N-channel | IOUT | 1 | 1.7 | mA | VDS = 0.5V, reset asserted, VCC = 1.0V | 16 | |
| Output Current, N-channel | IOUT | 3 | 14 | mA | VDS = 0.5V, reset asserted, VCC = 2.0V | 16 | |
| Output Current, N-channel | IOUT | 5 | 22 | mA | VDS = 0.5V, reset asserted, VCC = 3.0V | 16 | |
| Output Current, N-channel | IOUT | 6 | 26 | mA | VDS = 0.5V, reset asserted, VCC = 4.0V | 16 | |
| Output Current, N-channel | IOUT | 7 | 30 | mA | VDS = 0.5V, reset asserted, VCC = 5.0V | 16 | |
| VCC to OUT Detect Delay | tPD | 25 | µs | VCC falling from VTH- + 100mV to VTH-, 100mV at 10mV/µs | 16 | ||
| VCC to OUT Release Delay | tPR | 30 | 200 | µs | VCC rising from VTH+, 100mV to VTH+ + 100mV at 10mV/µs | 16 | |
| Threshold Temperature Coefficient | -100 | 100 | ppm/°C | 16 | |||
| Storage Temperature (VCC Off, VBAT Off) | TSTG | -55 | 150 | °C | VCC off, VBAT off | 13 | |
| Lead Solder Temperature | TSLD | 260 | °C | for 10 seconds | 13 | ||
| Input or Output Voltage | VIO | -0.3 | V | VCC + 0.3 upper limit printed as expression | 13 | ||
| Supply Voltage | VCC | -0.3 | 7 | V | 13 | ||
| Output Current | IO | 20 | mA | 13 | |||
| Power Dissipation | PD | 320 | mW | 13 |
CAD (KiCad official)
- Symbol:
STM1061N28WX6F - Footprint:
Package_TO_SOT_SMD:SOT-23-3 - 3D model: SOT-23-3, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.0050000000000001 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm1061n28wx6f-etched.step/stm1061n28wx6f-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm1061n28wx6f.step/stm1061n28wx6f.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (23 pp, sha256
5b1838531083a3d9, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).