3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSTC10F08XE-35I-PDIP40
STC Micro · Microcontroller Units (MCUs/MPUs/SOCs) · DIP-40
STC10F08XE-35I-PDIP40 from STC Micro, in a DIP-40. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | P1.0/CLKOUT2 | bidirectional | Standard I/O port 1 bit 0, which can be configured as the CLKOUT2 clock output of the independent baud-rate generator via WAKE_CLKO/BRTCLKO. |
| 2 | P1.1 | bidirectional | Standard I/O port 1 bit 1. |
| 3 | P1.2 | bidirectional | Standard I/O port 1 bit 2. |
| 4 | P1.3 | bidirectional | Standard I/O port 1 bit 3. |
| 5 | P1.4 | bidirectional | Standard I/O port 1 bit 4. |
| 6 | P1.5 | bidirectional | Standard I/O port 1 bit 5. |
| 7 | P1.6/RxD | bidirectional | Standard I/O port 1 bit 6 or alternate UART receive data input, selectable with AUXR1.UART_P1. |
| 8 | P1.7/TxD | bidirectional | Standard I/O port 1 bit 7 or alternate UART transmit data output, selectable with AUXR1.UART_P1. |
| 9 | P4.7/RST | bidirectional | Reset input (factory default is RST), which can be set to I/O port P4.7 during ISP programming; if used as I/O an external clock is required. |
| 10 | P3.0/RxD | bidirectional | Standard I/O port 3 bit 0 or UART1 receive data input, which can also wake the MCU from power-down. |
| 11 | P3.1/TxD | bidirectional | Standard I/O port 3 bit 1 or UART1 transmit data output. |
| 12 | P3.2/INT0 | bidirectional | Standard I/O port 3 bit 2 or external interrupt 0 input, triggered on falling edge or low level, and able to wake the MCU from power-down. |
| 13 | P3.3/INT1 | bidirectional | Standard I/O port 3 bit 3 or external interrupt 1 input, triggered on falling edge or low level, and able to wake the MCU from power-down. |
| 14 | P3.4/T0/INT/CLKOUT0 | bidirectional | Standard I/O port 3 bit 4, timer/counter 0 external input with falling-edge interrupt, or CLKOUT0 timer 0 clock output enabled via WAKE_CLKO/T0CLKO. |
| 15 | P3.5/T1/INT/CLKOUT1 | bidirectional | Standard I/O port 3 bit 5, timer/counter 1 external input with falling-edge interrupt, or CLKOUT1 timer 1 clock output enabled via WAKE_CLKO/T1CLKO. |
| 16 | P3.6/WR | bidirectional | Standard I/O port 3 bit 6 or external data memory write pulse output. |
| 17 | P3.7/RD | bidirectional | Standard I/O port 3 bit 7 or external data memory read pulse output. |
| 18 | XTAL2 | output | Output of the internal clock inverting amplifier to the other crystal terminal; may be left floating when an external clock source drives XTAL1. |
| 19 | XTAL1 | input | Input of the internal clock inverting amplifier for one crystal terminal, or the external clock source input. |
| 20 | Gnd | power_in | Ground. |
| 21 | P2.0 | bidirectional | Port 2 bit 0, quasi-bidirectional I/O or address bus bit A8 for external memory. |
| 22 | P2.1 | bidirectional | Port 2 bit 1, quasi-bidirectional I/O or address bus bit A9 for external memory. |
| 23 | P2.2 | bidirectional | Port 2 bit 2, quasi-bidirectional I/O or address bus bit A10 for external memory. |
| 24 | P2.3 | bidirectional | Port 2 bit 3, quasi-bidirectional I/O or address bus bit A11 for external memory. |
| 25 | P2.4 | bidirectional | Port 2 bit 4, quasi-bidirectional I/O or address bus bit A12 for external memory. |
| 26 | P2.5 | bidirectional | Port 2 bit 5, quasi-bidirectional I/O or address bus bit A13 for external memory. |
| 27 | P2.6 | bidirectional | Port 2 bit 6, quasi-bidirectional I/O or address bus bit A14 for external memory. |
| 28 | P2.7 | bidirectional | Port 2 bit 7, quasi-bidirectional I/O or address bus bit A15 for external memory. |
| 29 | NA/P4.4 | bidirectional | After reset a weak pull-up with no function; setting P4SW.4=1 makes it I/O port P4.4. |
| 30 | ALE/P4.5 | bidirectional | ALE address-latch signal output only during MOVX external access after reset; setting P4SW.5=1 makes it I/O port P4.5. |
| 31 | NA/P4.6 | bidirectional | After reset a weak pull-up with no function; setting P4SW.6=1 makes it I/O port P4.6. |
| 32 | P0.7 | bidirectional | Port 0 bit 7, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D7 / address bit A7 when used as the multiplexed bus. |
| 33 | P0.6 | bidirectional | Port 0 bit 6, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D6 / address bit A6 when used as the multiplexed bus. |
| 34 | P0.5 | bidirectional | Port 0 bit 5, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D5 / address bit A5 when used as the multiplexed bus. |
| 35 | P0.4 | bidirectional | Port 0 bit 4, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D4 / address bit A4 when used as the multiplexed bus. |
| 36 | P0.3 | bidirectional | Port 0 bit 3, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D3 / address bit A3 when used as the multiplexed bus. |
| 37 | P0.2 | bidirectional | Port 0 bit 2, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D2 / address bit A2 when used as the multiplexed bus. |
| 38 | P0.1 | bidirectional | Port 0 bit 1, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D1 / address bit A1 when used as the multiplexed bus. |
| 39 | P0.0 | bidirectional | Port 0 bit 0, quasi-bidirectional I/O with internal weak pull-up, or data bus bit D0 / address bit A0 when used as the multiplexed bus. |
| 40 | Vcc | power_in | Power supply, 5.5V to 3.8V/3.3V for the STC10Fxx series (3.8V or 3.3V being the selectable low-voltage reset threshold). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STC Micro |
| Package | DIP-40 |
| Category | Embedded Processors & Controllers |
| Pins | 40 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DC power supply (5V) | VDD - VSS | -0.3 | 5.5 | V | 471 | ||
| Operating temperature (I) | TA | -40 | 85 | ℃ | 471 | ||
| Storage temperature | TST | -55 | 125 | ℃ | 471 | ||
| Operating Voltage | VDD | 4.1 | 5 | 5.5 | V | 471 | |
| Input Low (P0,P1,P2,P3) | VIL1 | 0.8 | V | 5V | 471 | ||
| Input High (P0,P1,P2,P3) | VIH1 | 2 | V | 5V | 471 | ||
| Input High (RESET) | VIH2 | 2.2 | V | 5V | 471 | ||
| Operating Current | ICC | 4 | 20 | mA | 5V | 471 | |
| Sourcing Current for output high (P0,P1,P2,P3) (Quasi-output) | IOH1 | 150 | 230 | uA | 5V | 471 | |
| Logic 0 input current (P0,P1,P2,P3) | IIL | 50 | uA | Vpin=0V | 471 | ||
| Logic 1 to 0 transition current (P0,P1,P2,P3) | ITL | 100 | 270 | 600 | uA | Vpin=2.0V | 471 |
| Voltage on any pin | -0.3 | V | max printed as VCC + 0.3 | 471 | |||
| Power Down Current | IPD | 0.1 | uA | 5V; printed as <0.1 | 471 | ||
| Idle Current | IIDL | 3 | mA | 5V | 471 | ||
| Sink Current for output low (P0,P1,P2,P3) | IOL1 | 20 | mA | 5V@Vpin=0.45V | 471 | ||
| Sourcing Current for output high (P0,P1,P2,P3) (Push-Pull, Strong-output) | IOH2 | 20 | mA | 5V@Vpin=2.4V | 471 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | Accumulator contents and the contents of a sixteen-bit base register, which may be either the Data Pointer or the PC. In the latter case, the PC is incremented to the address of the | 184 |
CAD (KiCad official)
- Symbol:
STC10F08XE-35I-PDIP40 - Footprint:
Package_DIP:DIP-40_W15.24mm - 3D model: DIP-40_W15.24mm (KiCad packages3D, STEP)
- 3D model files:
stc10f08xe-35i-pdip40-etched.step/stc10f08xe-35i-pdip40-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stc10f08xe-35i-pdip40.step/stc10f08xe-35i-pdip40.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STC Micro datasheet (520 pp, sha256
7eeb33614d62821a, retrieved 2026-10-29, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).