3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownST25R3911B-AQFT
STMicroelectronics · RF Chips · QFN-32-EP(5x5)
ST25R3911B-AQFT from STMicroelectronics, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD_IO | power_in | Positive supply for peripheral communication; IO pins support 1.65 V to 5.5 V. |
| 2 | CSO | output | Capacitor sensor output (analog output). |
| 3 | VSP_D | power_out | Digital supply regulator output. |
| 4 | XTO | output | Xtal oscillator output for the 13.56 MHz or 27.12 MHz crystal. |
| 5 | XTI | input | Xtal oscillator input (analog input / digital input) for the 13.56 MHz or 27.12 MHz crystal. |
| 6 | VSN_D | power_in | Digital ground supply pad. |
| 7 | VSP_A | power_out | Analog supply regulator output. |
| 8 | VDD | power_in | External positive supply, 2.4 V to 5.5 V operating range (absolute maximum 6.0 V). |
| 9 | VSP_RF | power_out | Supply regulator output for antenna drivers. |
| 10 | RFO1 | output | Antenna driver output 1 (low impedance, 1 Ohm driver). |
| 11 | RFO2 | output | Antenna driver output 2 (low impedance, 1 Ohm driver). |
| 12 | VSN_RF | power_in | Ground of antenna drivers. |
| 13 | TRIM1_3 | bidirectional | Analog I/O to trim the antenna resonant circuit; HVNMOS switch to VSS (6.25 Ohm typ. on-resistance, 25 V breakdown). |
| 14 | TRIM2_3 | bidirectional | Analog I/O to trim the antenna resonant circuit; HVNMOS switch to VSS (6.25 Ohm typ. on-resistance, 25 V breakdown); left open when a single driver is used. |
| 15 | TRIM1_2 | bidirectional | Analog I/O to trim the antenna resonant circuit via a binary-weighted HVNMOS switch to VSS (25 V breakdown). |
| 16 | TRIM2_2 | bidirectional | Analog I/O to trim the antenna resonant circuit via a binary-weighted HVNMOS switch to VSS; left open when a single driver is used. |
| 17 | TRIM1_1 | bidirectional | Analog I/O to trim the antenna resonant circuit via a binary-weighted HVNMOS switch to VSS (25 V breakdown). |
| 18 | TRIM2_1 | bidirectional | Analog I/O to trim the antenna resonant circuit via a binary-weighted HVNMOS switch to VSS; left open when a single driver is used. |
| 19 | TRIM1_0 | bidirectional | Analog I/O to trim the antenna resonant circuit; LSB HVNMOS switch to VSS (50 Ohm typ. on-resistance at 3 V VSP_D, 25 V breakdown). |
| 20 | TRIM2_0 | bidirectional | Analog I/O to trim the antenna resonant circuit; LSB HVNMOS switch to VSS (50 Ohm typ. on-resistance at 3 V VSP_D); left open when a single driver is used. |
| 21 | VSS | power_in | Ground, die substrate potential. |
| 22 | RFI1 | input | Receiver input 1 (analog input). |
| 23 | RFI2 | input | Receiver input 2 (analog input). |
| 24 | AGD | bidirectional | Analog reference voltage (analog I/O). |
| 25 | CSI | input | Capacitor sensor input (analog input). |
| 26 | VSN_A | power_in | Analog ground supply pad. |
| 27 | IRQ | output | Interrupt request output; also outputs the PM demodulation chain in transparent mode. |
| 28 | MCU_CLK | output | Microcontroller clock output. |
| 29 | MISO | tri_state | Serial Peripheral Interface data output (digital output / tristate). |
| 30 | MOSI | input | Serial Peripheral Interface data input. |
| 31 | SCLK | input | Serial Peripheral Interface clock. |
| 32 | /SS | input | Serial Peripheral Interface enable, active low. |
| 33 | VSS | power_in | Exposed pad: ground, die substrate potential, connected to VSS on PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | QFN-32-EP(5x5) |
| Category | RF & Radio |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DC supply voltage | VDD | -0.5 | 6 | V | 97 | ||
| DC_IO supply voltage | VDD_IO | -0.5 | 6 | V | 97 | ||
| Input pin voltage TRIM pins | VINTRIM | -0.5 | 25 | V | 97 | ||
| Input pin voltage for peripheral communication pins | VIN | -0.5 | 6.5 | V | 97 | ||
| Input voltage for analog pins | VINA | -0.5 | 6 | V | 97 | ||
| Input current (latch-up immunity) | Iscr | -100 | 100 | mA | Norm: JEDEC 78 | 97 | |
| Drive capability of output driver | Ioutmax | 0 | 600 | mA | 97 | ||
| Electrostatic discharge | ESD | -2 | 2 | kV | JS-001-2014 (Human body model) | 97 | |
| Electrostatic discharge TRIMx_x pins | ESD | -500 | 500 | V | JS-001-2014 (Human body model), valid for TRIMx_x pins (pins 13 - 20) | 97 | |
| Storage temperature | Tstrg | -55 | 125 | °C | 97 | ||
| Package body temperature | Tbody | 260 | °C | IPC/JEDEC J-STD-020 | 97 | ||
| Relative humidity non-condensing | RHNC | 5 | 85 | % | 97 | ||
| Positive supply voltage | VDD | 2.4 | 5.5 | V | 98 | ||
| Peripheral communication supply voltage | VDD_IO | 1.65 | 5.5 | V | 98 | ||
| Negative supply voltage | VSS | 0 | 0 | V | 98 | ||
| Input pin voltage TRIM pins | VINTRIM | 20 | V | 98 | |||
| Junction temperature | TJUN | -40 | 125 | °C | 98 | ||
| RFI input amplitude | VRFI_A | 0.15 | 3 | Vpp | Minimum is for NFC receive mode; recommended 2.5 Vpp in HF reader mode and NFC transmit mode | 98 | |
| RFO driver current | RFO | 0 | 500 | mA | 98 | ||
| Input leakage current | ILEAK | -1 | 1 | µA | CMOS inputs \SS, MOSI, SCLK | 98 | |
| Capacitive load | CL | 0 | 50 | pF | CMOS outputs MISO, IRQ, MCU_CLK; io_18=0 | 99 | |
| Output resistance | RO | 0 | 250 | 550 | Ω | CMOS outputs MISO, IRQ, MCU_CLK; io_18=0 | 99 |
| Pull-down resistance pin MISO | RPD | 5 | 10 | 15 | kΩ | Pull-down can be enabled while MISO output is in tristate | 99 |
| Supply current in Power-down mode | IPD | 0.7 | 2 | µA | VDD=3.3 V, 25 °C; register 00h=0Fh, 01h=80h, 02h=00h, 03h=08h | 99 | |
| Supply current in initial NFC Target mode | INFCT | 3.5 | 7 | µA | VDD=3.3 V, 25 °C; register 03h=80h (enable NFC Target mode) | 99 | |
| Supply current in Wake-up mode | IWU | 3.6 | 8 | µA | VDD=3.3 V, 25 °C; register 02h=04h, 31h=08h (100 ms timeout) | 99 | |
| Supply current in Ready mode | IRD | 5.4 | 7.5 | mA | VDD=3.3 V, 25 °C; register 01h=C0h, 02h=80h, 03h=08h, VSP_A and VSP_D shorted | 99 | |
| Supply current, all active | IAL | 8.7 | 12.5 | mA | VDD=3.3 V, 25 °C; register 02h=E8h, 27h=FFh, VSP_A and VSP_D shorted | 99 | |
| Supply current, all active, low power receiver mode | ILP | 6.8 | 10 | mA | VDD=3.3 V, 25 °C; register 0Bh=80h (low power mode), 02h=E8h, 27h=FFh | 99 | |
| RFO1 and RFO2 driver output resistance | RRFO | 0.25 | 0.6 | 1.8 | Ω | IRFO = 10 mA | 99 |
| Load impedance across RFO1 and RFO2 | Zload | 8 | 10 | 50 | Ω | Lower than minimum value can cause permanent damage | 100 |
| RFI input sensitivity | VRFI | 0.5 | mVrms | fSUB = 848 kHz, AM channel with peak detector input stage selected | 100 | ||
| RFI input resistance | RRFI | 5 | 10 | 15 | kΩ | 100 | |
| Power on Reset voltage | VPOR | 1.31 | 1.5 | 1.75 | V | 100 | |
| AGD voltage | VAGD | 1.4 | 1.5 | 1.6 | V | register 01h=C0h, 02h=80h, 03h=08h, VSP_A and VSP_D shorted | 100 |
| Regulated voltage | VREG | 2.8 | 3 | 3.32 | V | Manual regulator mode, set to 3.0 V, measured on pin VSP_RF; register 02h=E8h, 2Ah=D8h | 100 |
| Oscillator start-up time | TOSC | 0.65 | 0.7 | 10 | ms | 13.56 MHz or 27.12 MHz crystal, ESRMAX= 150 Ω max | 100 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | The reflow peak soldering temperature (body temperature) is specified according to IPC/JEDEC J-STD-020 “Moisture/Reflow | 97 | |
| contacts | copper | capacitance between two copper patches connected to the CSI and CSO pins. The capacitance changes with | 3 |
CAD (KiCad official)
- Symbol:
ST25R3911B-AQFT - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
st25r3911b-aqft-etched.step/st25r3911b-aqft-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);st25r3911b-aqft.step/st25r3911b-aqft.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (116 pp, sha256
722073ea1b9b98cd, retrieved 2026-10-22, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).