component
ST16C2550IQ48-F
Public Made by Adomby adom
MaxLinear UART, TQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
671e776
ST16C2550IQ48-F
MaxLinear · UART · TQFP-48(7x7)
ST16C2550IQ48-F from MaxLinear, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D5 | bidirectional | Data bus line bit 5; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 2 | D6 | bidirectional | Data bus line bit 6; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 3 | D7 | bidirectional | Data bus line bit 7; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 4 | RXB | input | UART channel B Receive Data; normal receive data input must idle at logic 1, and if unused it should be tied to VCC or pulled high via a 100k ohm resistor. |
| 5 | RXA | input | UART channel A Receive Data; normal receive data input must idle at logic 1, and if unused it should be tied to VCC or pulled high via a 100k ohm resistor. |
| 6 | TXRDYB# | output | UART channel B Transmitter Ready (active low) that provides the TX FIFO/THR status per Table 2; leave unconnected if not used. |
| 7 | TXA | output | UART channel A Transmit Data output; leave unconnected if not used. |
| 8 | TXB | output | UART channel B Transmit Data output; leave unconnected if not used. |
| 9 | OP2B# | output | Output Port 2 channel B, set by the user through MCR[3]; it goes to logic 0 with INTB active when MCR[3] is 1 and must not be used as a general output because it disturbs INTB. |
| 10 | CSA# | input | UART channel A select (active low) that enables channel A for data bus operation. |
| 11 | CSB# | input | UART channel B select (active low) that enables channel B for data bus operation. |
| 12 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 13 | XTAL1 | input | Crystal or external clock input. |
| 14 | XTAL2 | output | Crystal or buffered clock output. |
| 15 | IOW# | input | Input/Output Write Strobe (active low); the falling edge starts an internal write cycle and the rising edge transfers the data byte on the data bus to the addressed register. |
| 16 | CDB# | input | UART channel B Carrier-Detect (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 17 | GND | power_in | Power supply common, ground. |
| 18 | RXRDYB# | output | UART channel B Receiver Ready (active low) that provides the RX FIFO/RHR status per Table 2; leave unconnected if not used. |
| 19 | IOR# | input | Input/Output Read Strobe (active low); the falling edge starts an internal read cycle and the data byte is placed on the data bus for the host to read on the rising edge. |
| 20 | DSRB# | input | UART channel B Data-Set-Ready (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 21 | RIB# | input | UART channel B Ring-Indicator (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 22 | RTSB# | output | UART channel B Request-to-Send (active low) or general purpose output; leave unconnected if not used. |
| 23 | CTSB# | input | UART channel B Clear-to-Send (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 24 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 25 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 26 | A2 | input | Address data line bit 2 of A2:A0, which selects one of the internal registers in UART channel A/B during a data bus transaction. |
| 27 | A1 | input | Address data line bit 1 of A2:A0, which selects one of the internal registers in UART channel A/B during a data bus transaction. |
| 28 | A0 | input | Address data line bit 0 of A2:A0, which selects one of the internal registers in UART channel A/B during a data bus transaction. |
| 29 | INTB | output | UART channel B Interrupt output; it is active when MCR[3] is set to 1 and three-state when MCR[3] is 0 (default), with OP2B# following the same state. |
| 30 | INTA | output | UART channel A Interrupt output; it is active when MCR[3] is set to 1 and three-state when MCR[3] is 0 (default), with OP2A# following the same state. |
| 31 | RXRDYA# | output | UART channel A Receiver Ready (active low) that provides the RX FIFO/RHR status per Table 2; leave unconnected if not used. |
| 32 | OP2A# | output | Output Port 2 channel A, set by the user through MCR[3]; it must not be used as a general output because it disturbs the INTA output functionality. |
| 33 | RTSA# | output | UART channel A Request-to-Send (active low) or general purpose output; leave unconnected if not used. |
| 34 | DTRA# | output | UART channel A Data-Terminal-Ready (active low) or general purpose output; leave unconnected if not used. |
| 35 | DTRB# | output | UART channel B Data-Terminal-Ready (active low) or general purpose output; leave unconnected if not used. |
| 36 | RESET | input | Reset (active high); a logic 1 pulse longer than 40 ns resets the internal registers and all outputs, with the UART transmitter output held at logic 1 during reset. |
| 37 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 38 | CTSA# | input | UART channel A Clear-to-Send (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 39 | DSRA# | input | UART channel A Data-Set-Ready (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 40 | CDA# | input | UART channel A Carrier-Detect (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 41 | RIA# | input | UART channel A Ring-Indicator (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 42 | VCC | power_in | Power supply, 2.97V to 5.5V; all inputs are 5V tolerant for devices with top marking "A2 YYWW" and newer. |
| 43 | TXRDYA# | output | UART channel A Transmitter Ready (active low) that provides the TX FIFO/THR status per Table 2; leave unconnected if not used. |
| 44 | D0 | bidirectional | Data bus line bit 0; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 45 | D1 | bidirectional | Data bus line bit 1; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 46 | D2 | bidirectional | Data bus line bit 2; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 47 | D3 | bidirectional | Data bus line bit 3; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 48 | D4 | bidirectional | Data bus line bit 4; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | TQFP-48(7x7) |
| Category | Interface ICs |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Range | 7 | V | 26 | ||||
| Voltage at Any Pin | -0.3 | 5.5 | V | min printed as GND-0.3 V | 26 | ||
| Operating Temperature | -40 | 85 | °C | industrial grade | 26 | ||
| Storage Temperature | -65 | 150 | °C | 26 | |||
| Package Dissipation | 500 | mW | 26 | ||||
| Power supply voltage | VCC | 2.97 | 5.5 | V | pin description: 2.97V to 5.5V power supply | 4 | |
| Clock Input Low Level | VILCK | -0.3 | 0.6 | V | VCC = 3.3V ±10% column | 26 | |
| Clock Input Low Level | VILCK | -0.5 | 0.6 | V | VCC = 5.0V ±10% column | 26 | |
| Clock Input High Level | VIHCK | 2.4 | 5.5 | V | VCC = 3.3V ±10% column | 26 | |
| Clock Input High Level | VIHCK | 3 | 5.5 | V | VCC = 5.0V ±10% column | 26 | |
| Input Low Voltage | VIL | -0.3 | 0.8 | V | VCC = 3.3V ±10% column | 26 | |
| Input Low Voltage | VIL | -0.5 | 0.8 | V | VCC = 5.0V ±10% column | 26 | |
| Input High Voltage | VIH | 2 | 5.5 | V | VCC = 3.3V ±10% column | 26 | |
| Input High Voltage | VIH | 2.2 | 5.5 | V | VCC = 5.0V ±10% column | 26 | |
| Output Low Voltage | VOL | 0.4 | V | IOL = 6 mA; VCC = 3.3V ±10% column | 26 | ||
| Output High Voltage | VOH | 2 | V | IOL = 4 mA (as printed); VCC = 3.3V ±10% column | 26 | ||
| Output High Voltage | VOH | 2.4 | V | IOL = 4 mA (as printed); VCC = 5.0V ±10% column | 26 | ||
| Input Low Leakage Current | IIL | -10 | 10 | uA | IOH = -6 mA (as printed); VCC = 3.3V ±10% column | 26 | |
| Input High Leakage Current | IIH | -10 | 10 | uA | IOH = -1 mA (as printed); VCC = 3.3V ±10% column | 26 | |
| Input Pin Capacitance | CIN | 5 | pF | 26 | |||
| Power Supply Current | ICC | 1.3 | mA | VCC = 3.3V ±10% column | 26 | ||
| Power Supply Current | ICC | 3 | mA | VCC = 5.0V ±10% column | 26 | ||
| External Clock Frequency | OSC | 30 | MHz | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| External Clock Frequency | OSC | 64 | MHz | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Clock Pulse Duration | CLK | 17 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Clock Pulse Duration | CLK | 8 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Chip Select Width | TCS | 70 | ns | VCC = 3.3V ±10% column; *55 ns if VCC = 3.3V +10%/-5% and TA = 0 to 70°C (See Figure 12); 70 pF load where applicable | 27 | ||
| Chip Select Width | TCS | 40 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| IOR# Strobe Width | TRD | 70 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| IOR# Strobe Width | TRD | 40 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Read or Write Cycle Delay | TDY | 70 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Read or Write Cycle Delay | TDY | 40 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Data Access Time | TRDV | 35 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Data Access Time | TRDV | 25 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Data Disable Time | TDD | 0 | 25 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | |
| Data Disable Time | TDD | 0 | 15 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | |
| IOW# Strobe Width | TWR | 40 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| IOW# Strobe Width | TWR | 25 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Data Setup Time | TDS | 20 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Data Setup Time | TDS | 15 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Data Hold Time | TDH | 5 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Delay From IOW# To Output | TWDO | 50 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Delay From IOW# To Output | TWDO | 40 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Delay From Initial INT Reset To Transmit Start | TINT | 8 | 24 | Bclk | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | |
| Address Setup Time | TAS | 5 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Address Setup Time | TAS | 0 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Address Hold Time | TAH | 10 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Address Hold Time | TAH | 5 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 | ||
| Reset Pulse Width | TRST | 40 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 28 | ||
| Delay From Stop To Set Interrupt | TSSI | 1 | Bclk | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 | ||
| Thermal Resistance theta-ja (48-TQFP) | theta-ja | 59 | °C/W | 48-TQFP; margin of error ±15% | 26 | ||
| Thermal Resistance theta-jc (48-TQFP) | theta-jc | 16 | °C/W | 48-TQFP; margin of error ±15% | 26 |
CAD (KiCad official)
- Symbol:
ST16C2550IQ48-F - Footprint:
Package_QFP:TQFP-48_7x7mm_P0.5mm - 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
st16c2550iq48-f-etched.step/st16c2550iq48-f-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);st16c2550iq48-f.step/st16c2550iq48-f.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MaxLinear datasheet (37 pp, sha256
bbe966b40d1dfcc5, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ST16C2550IQ48-F
**MaxLinear** · UART · TQFP-48(7x7)
ST16C2550IQ48-F from MaxLinear, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D5 | bidirectional | Data bus line bit 5; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 2 | D6 | bidirectional | Data bus line bit 6; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 3 | D7 | bidirectional | Data bus line bit 7; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 4 | RXB | input | UART channel B Receive Data; normal receive data input must idle at logic 1, and if unused it should be tied to VCC or pulled high via a 100k ohm resistor. |
| 5 | RXA | input | UART channel A Receive Data; normal receive data input must idle at logic 1, and if unused it should be tied to VCC or pulled high via a 100k ohm resistor. |
| 6 | TXRDYB# | output | UART channel B Transmitter Ready (active low) that provides the TX FIFO/THR status per Table 2; leave unconnected if not used. |
| 7 | TXA | output | UART channel A Transmit Data output; leave unconnected if not used. |
| 8 | TXB | output | UART channel B Transmit Data output; leave unconnected if not used. |
| 9 | OP2B# | output | Output Port 2 channel B, set by the user through MCR[3]; it goes to logic 0 with INTB active when MCR[3] is 1 and must not be used as a general output because it disturbs INTB. |
| 10 | CSA# | input | UART channel A select (active low) that enables channel A for data bus operation. |
| 11 | CSB# | input | UART channel B select (active low) that enables channel B for data bus operation. |
| 12 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 13 | XTAL1 | input | Crystal or external clock input. |
| 14 | XTAL2 | output | Crystal or buffered clock output. |
| 15 | IOW# | input | Input/Output Write Strobe (active low); the falling edge starts an internal write cycle and the rising edge transfers the data byte on the data bus to the addressed register. |
| 16 | CDB# | input | UART channel B Carrier-Detect (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 17 | GND | power_in | Power supply common, ground. |
| 18 | RXRDYB# | output | UART channel B Receiver Ready (active low) that provides the RX FIFO/RHR status per Table 2; leave unconnected if not used. |
| 19 | IOR# | input | Input/Output Read Strobe (active low); the falling edge starts an internal read cycle and the data byte is placed on the data bus for the host to read on the rising edge. |
| 20 | DSRB# | input | UART channel B Data-Set-Ready (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 21 | RIB# | input | UART channel B Ring-Indicator (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 22 | RTSB# | output | UART channel B Request-to-Send (active low) or general purpose output; leave unconnected if not used. |
| 23 | CTSB# | input | UART channel B Clear-to-Send (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 24 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 25 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 26 | A2 | input | Address data line bit 2 of A2:A0, which selects one of the internal registers in UART channel A/B during a data bus transaction. |
| 27 | A1 | input | Address data line bit 1 of A2:A0, which selects one of the internal registers in UART channel A/B during a data bus transaction. |
| 28 | A0 | input | Address data line bit 0 of A2:A0, which selects one of the internal registers in UART channel A/B during a data bus transaction. |
| 29 | INTB | output | UART channel B Interrupt output; it is active when MCR[3] is set to 1 and three-state when MCR[3] is 0 (default), with OP2B# following the same state. |
| 30 | INTA | output | UART channel A Interrupt output; it is active when MCR[3] is set to 1 and three-state when MCR[3] is 0 (default), with OP2A# following the same state. |
| 31 | RXRDYA# | output | UART channel A Receiver Ready (active low) that provides the RX FIFO/RHR status per Table 2; leave unconnected if not used. |
| 32 | OP2A# | output | Output Port 2 channel A, set by the user through MCR[3]; it must not be used as a general output because it disturbs the INTA output functionality. |
| 33 | RTSA# | output | UART channel A Request-to-Send (active low) or general purpose output; leave unconnected if not used. |
| 34 | DTRA# | output | UART channel A Data-Terminal-Ready (active low) or general purpose output; leave unconnected if not used. |
| 35 | DTRB# | output | UART channel B Data-Terminal-Ready (active low) or general purpose output; leave unconnected if not used. |
| 36 | RESET | input | Reset (active high); a logic 1 pulse longer than 40 ns resets the internal registers and all outputs, with the UART transmitter output held at logic 1 during reset. |
| 37 | NC | unconnected | No connection; the pin is open but should typically be connected to GND for good design practice. |
| 38 | CTSA# | input | UART channel A Clear-to-Send (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 39 | DSRA# | input | UART channel A Data-Set-Ready (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 40 | CDA# | input | UART channel A Carrier-Detect (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 41 | RIA# | input | UART channel A Ring-Indicator (active low) or general purpose input; it should be connected to VCC when not used and has no effect on the UART. |
| 42 | VCC | power_in | Power supply, 2.97V to 5.5V; all inputs are 5V tolerant for devices with top marking "A2 YYWW" and newer. |
| 43 | TXRDYA# | output | UART channel A Transmitter Ready (active low) that provides the TX FIFO/THR status per Table 2; leave unconnected if not used. |
| 44 | D0 | bidirectional | Data bus line bit 0; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 45 | D1 | bidirectional | Data bus line bit 1; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 46 | D2 | bidirectional | Data bus line bit 2; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 47 | D3 | bidirectional | Data bus line bit 3; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
| 48 | D4 | bidirectional | Data bus line bit 4; the data bus lines [7:0] are bidirectional and transfer data to and from the UART registers. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | TQFP-48(7x7) |
| Category | Interface ICs |
| Pins | 48 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Range | | | | 7 | V | | 26 |
| Voltage at Any Pin | | -0.3 | | 5.5 | V | min printed as GND-0.3 V | 26 |
| Operating Temperature | | -40 | | 85 | °C | industrial grade | 26 |
| Storage Temperature | | -65 | | 150 | °C | | 26 |
| Package Dissipation | | | | 500 | mW | | 26 |
| Power supply voltage | VCC | 2.97 | | 5.5 | V | pin description: 2.97V to 5.5V power supply | 4 |
| Clock Input Low Level | VILCK | -0.3 | | 0.6 | V | VCC = 3.3V ±10% column | 26 |
| Clock Input Low Level | VILCK | -0.5 | | 0.6 | V | VCC = 5.0V ±10% column | 26 |
| Clock Input High Level | VIHCK | 2.4 | | 5.5 | V | VCC = 3.3V ±10% column | 26 |
| Clock Input High Level | VIHCK | 3 | | 5.5 | V | VCC = 5.0V ±10% column | 26 |
| Input Low Voltage | VIL | -0.3 | | 0.8 | V | VCC = 3.3V ±10% column | 26 |
| Input Low Voltage | VIL | -0.5 | | 0.8 | V | VCC = 5.0V ±10% column | 26 |
| Input High Voltage | VIH | 2 | | 5.5 | V | VCC = 3.3V ±10% column | 26 |
| Input High Voltage | VIH | 2.2 | | 5.5 | V | VCC = 5.0V ±10% column | 26 |
| Output Low Voltage | VOL | | | 0.4 | V | IOL = 6 mA; VCC = 3.3V ±10% column | 26 |
| Output High Voltage | VOH | 2 | | | V | IOL = 4 mA (as printed); VCC = 3.3V ±10% column | 26 |
| Output High Voltage | VOH | 2.4 | | | V | IOL = 4 mA (as printed); VCC = 5.0V ±10% column | 26 |
| Input Low Leakage Current | IIL | -10 | | 10 | uA | IOH = -6 mA (as printed); VCC = 3.3V ±10% column | 26 |
| Input High Leakage Current | IIH | -10 | | 10 | uA | IOH = -1 mA (as printed); VCC = 3.3V ±10% column | 26 |
| Input Pin Capacitance | CIN | | | 5 | pF | | 26 |
| Power Supply Current | ICC | | | 1.3 | mA | VCC = 3.3V ±10% column | 26 |
| Power Supply Current | ICC | | | 3 | mA | VCC = 5.0V ±10% column | 26 |
| External Clock Frequency | OSC | | | 30 | MHz | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| External Clock Frequency | OSC | | | 64 | MHz | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Clock Pulse Duration | CLK | 17 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Clock Pulse Duration | CLK | 8 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Chip Select Width | TCS | 70 | | | ns | VCC = 3.3V ±10% column; *55 ns if VCC = 3.3V +10%/-5% and TA = 0 to 70°C (See Figure 12); 70 pF load where applicable | 27 |
| Chip Select Width | TCS | 40 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| IOR# Strobe Width | TRD | 70 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| IOR# Strobe Width | TRD | 40 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Read or Write Cycle Delay | TDY | 70 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Read or Write Cycle Delay | TDY | 40 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Data Access Time | TRDV | | | 35 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Data Access Time | TRDV | | | 25 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Data Disable Time | TDD | 0 | | 25 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Data Disable Time | TDD | 0 | | 15 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| IOW# Strobe Width | TWR | 40 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| IOW# Strobe Width | TWR | 25 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Data Setup Time | TDS | 20 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Data Setup Time | TDS | 15 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Data Hold Time | TDH | 5 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Delay From IOW# To Output | TWDO | | | 50 | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Delay From IOW# To Output | TWDO | | | 40 | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Delay From Initial INT Reset To Transmit Start | TINT | 8 | | 24 | Bclk | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Address Setup Time | TAS | 5 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Address Setup Time | TAS | 0 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Address Hold Time | TAH | 10 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Address Hold Time | TAH | 5 | | | ns | VCC = 5.0V ±10% column; 70 pF load where applicable | 27 |
| Reset Pulse Width | TRST | 40 | | | ns | VCC = 3.3V ±10% column; 70 pF load where applicable | 28 |
| Delay From Stop To Set Interrupt | TSSI | 1 | | | Bclk | VCC = 3.3V ±10% column; 70 pF load where applicable | 27 |
| Thermal Resistance theta-ja (48-TQFP) | theta-ja | | 59 | | °C/W | 48-TQFP; margin of error ±15% | 26 |
| Thermal Resistance theta-jc (48-TQFP) | theta-jc | | 16 | | °C/W | 48-TQFP; margin of error ±15% | 26 |
## CAD (KiCad official)
- Symbol: `ST16C2550IQ48-F`
- Footprint: `Package_QFP:TQFP-48_7x7mm_P0.5mm`
- 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files: `st16c2550iq48-f-etched.step` / `st16c2550iq48-f-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `st16c2550iq48-f.step` / `st16c2550iq48-f.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [MaxLinear datasheet](docs/st16c2550iq48-f-datasheet.pdf) (37 pp, sha256 `bbe966b40d1dfcc5`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/st16c2550iq48-f-datasheet.pdf)