main
History Download
Ray Publish 0.1.0 7dc2c26

SQ27000SXC

Silergy Corp · DC-DC Converters · DFN-8(4x4)

SQ27000SXC from Silergy Corp, in a DFN-8(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground pin; the datasheet also specifies a GND exposed pad and recommends maximizing the PCB copper area connected to GND for thermal and noise performance.
2 IN power_in Input pin supplied from 7V to 100V, to be decoupled to GND with a low-ESR ceramic capacitor placed close to the IN and GND pins.
3 EN input Enable control pin with an accurate 1.225V rising threshold (1.185V to 1.265V), which can also set the VIN turn-on voltage through a resistor divider.
4 RON input Connect a resistor from this pin to IN to set the top switch on-time and switching frequency, with fOSC of 350kHz to 650kHz at VIN=48V and RON=1.1MΩ.
5 FB input Output feedback pin connected to the center point of the output divider, programming VOUT = 1.225×(1+R1/R2) with VFB typically 1.225V.
6 VCC power_in Supply input of the internal 4V LDO, which can be fed from an auxiliary 4.8V to 28V source through a diode to shut off LDO power dissipation from IN.
7 BS power_out Bootstrap pin that supplies the high-side gate driver, with a 0.1µF ceramic capacitor connected between BS and LX.
8 LX output Inductor pin connected to the switching node; its PCB copper area should be minimized to avoid noise, and dynamic LX voltage is limited to IN+3V to GND-5V for 50ns.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Silergy Corp
Package DFN-8(4x4)
Category Power Supply Chip
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input pin voltage (IN) -0.3 100 V 4
EN, LX, RON voltage -0.3 V 4
BS-LX voltage -0.3 6 V 4
FB voltage -0.3 6 V 4
VCC voltage -0.3 30 V 4
Storage temperature range -65 150 °C 4
Junction temperature range (absolute maximum) -40 150 °C 4
Lead temperature (soldering) 260 °C 10 sec. 4
Power dissipation DFN4×4-8 PD 2.8 W TA = 25°C 4
Supply input voltage 7 100 V 4
Junction temperature range (recommended) -40 125 °C 4
Ambient temperature range -40 85 °C 4
Input voltage range VIN 7 100 V 5
Input UVLO rising threshold VIN,UVLO 5.8 6.3 6.8 V 5
Input UVLO hysteresis VHYS 0.15 0.25 0.35 V 5
Shutdown current ISHDN 8 30 µA EN=0 5
Feedback reference voltage VREF 1.2 1.225 1.25 V 5
FB input current IFB -100 100 nA VFB=3.3V 5
Top FET peak current limit ILIM,TOP 0.9 1.2 1.5 A 5
Bottom FET valley current limit ILIM,BOTTOM 0.6 0.8 1 A 5
Negative current limit ILIM,NEG -480 -650 -820 mA 5
EN rising threshold VEN 1.185 1.225 1.265 V 5
EN hysteresis input current IEN, HYS -10 -20 -29 μA 5
Switching frequency fOSC 350 500 650 kHz VIN=48V, RON=1.1MΩ 5
Top FET on-resistance RDS(ON)1 500 mΩ 5
Bottom FET on-resistance RDS(ON)2 285 mΩ 5
VCC input rising UVLO threshold VVCC,UVLO 4.5 V 5
VCC input UVLO hysteresis VVCC,HYS 0.3 V 5
Min ON time tON 90 ns 5
Min OFF time tOFF 200 ns 5
Thermal shutdown temperature TSD 150 °C 5
Thermal shutdown hysteresis THYS 15 °C 5
Package thermal resistance, junction-to-ambient θJA 44.5 °C/W JESD51-2, TA = 25°C, 4-layer PCB per JESD51-7 with thermal via 4
Package thermal resistance, junction-to-case θJC 22.1 °C/W 4
Package thermal resistance, junction-to-board θJB 14.1 °C/W 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper the GND pin. 4) The PCB copper area associated with the LX pin 11

CAD (KiCad official)

  • Symbol: SQ27000SXC
  • Footprint: Package_DFN_QFN:DFN-8-1EP_4x4mm_P0.8mm_EP2.5x3.6mm
  • 3D model: DFN-8(4x4) (KiCad packages3D, STEP)
  • 3D model files: sq27000sxc-etched.step / sq27000sxc-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sq27000sxc.step / sq27000sxc.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Silergy Corp datasheet (14 pp, sha256 bb4812bd2ab805eb, retrieved 2026-11-04, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF