Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
SQ27000SXC
Silergy Corp · DC-DC Converters · DFN-8(4x4)
SQ27000SXC from Silergy Corp, in a DFN-8(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin; the datasheet also specifies a GND exposed pad and recommends maximizing the PCB copper area connected to GND for thermal and noise performance. |
| 2 | IN | power_in | Input pin supplied from 7V to 100V, to be decoupled to GND with a low-ESR ceramic capacitor placed close to the IN and GND pins. |
| 3 | EN | input | Enable control pin with an accurate 1.225V rising threshold (1.185V to 1.265V), which can also set the VIN turn-on voltage through a resistor divider. |
| 4 | RON | input | Connect a resistor from this pin to IN to set the top switch on-time and switching frequency, with fOSC of 350kHz to 650kHz at VIN=48V and RON=1.1MΩ. |
| 5 | FB | input | Output feedback pin connected to the center point of the output divider, programming VOUT = 1.225×(1+R1/R2) with VFB typically 1.225V. |
| 6 | VCC | power_in | Supply input of the internal 4V LDO, which can be fed from an auxiliary 4.8V to 28V source through a diode to shut off LDO power dissipation from IN. |
| 7 | BS | power_out | Bootstrap pin that supplies the high-side gate driver, with a 0.1µF ceramic capacitor connected between BS and LX. |
| 8 | LX | output | Inductor pin connected to the switching node; its PCB copper area should be minimized to avoid noise, and dynamic LX voltage is limited to IN+3V to GND-5V for 50ns. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Silergy Corp |
| Package | DFN-8(4x4) |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input pin voltage (IN) | -0.3 | 100 | V | 4 | |||
| EN, LX, RON voltage | -0.3 | V | 4 | ||||
| BS-LX voltage | -0.3 | 6 | V | 4 | |||
| FB voltage | -0.3 | 6 | V | 4 | |||
| VCC voltage | -0.3 | 30 | V | 4 | |||
| Storage temperature range | -65 | 150 | °C | 4 | |||
| Junction temperature range (absolute maximum) | -40 | 150 | °C | 4 | |||
| Lead temperature (soldering) | 260 | °C | 10 sec. | 4 | |||
| Power dissipation DFN4×4-8 | PD | 2.8 | W | TA = 25°C | 4 | ||
| Supply input voltage | 7 | 100 | V | 4 | |||
| Junction temperature range (recommended) | -40 | 125 | °C | 4 | |||
| Ambient temperature range | -40 | 85 | °C | 4 | |||
| Input voltage range | VIN | 7 | 100 | V | 5 | ||
| Input UVLO rising threshold | VIN,UVLO | 5.8 | 6.3 | 6.8 | V | 5 | |
| Input UVLO hysteresis | VHYS | 0.15 | 0.25 | 0.35 | V | 5 | |
| Shutdown current | ISHDN | 8 | 30 | µA | EN=0 | 5 | |
| Feedback reference voltage | VREF | 1.2 | 1.225 | 1.25 | V | 5 | |
| FB input current | IFB | -100 | 100 | nA | VFB=3.3V | 5 | |
| Top FET peak current limit | ILIM,TOP | 0.9 | 1.2 | 1.5 | A | 5 | |
| Bottom FET valley current limit | ILIM,BOTTOM | 0.6 | 0.8 | 1 | A | 5 | |
| Negative current limit | ILIM,NEG | -480 | -650 | -820 | mA | 5 | |
| EN rising threshold | VEN | 1.185 | 1.225 | 1.265 | V | 5 | |
| EN hysteresis input current | IEN, HYS | -10 | -20 | -29 | μA | 5 | |
| Switching frequency | fOSC | 350 | 500 | 650 | kHz | VIN=48V, RON=1.1MΩ | 5 |
| Top FET on-resistance | RDS(ON)1 | 500 | mΩ | 5 | |||
| Bottom FET on-resistance | RDS(ON)2 | 285 | mΩ | 5 | |||
| VCC input rising UVLO threshold | VVCC,UVLO | 4.5 | V | 5 | |||
| VCC input UVLO hysteresis | VVCC,HYS | 0.3 | V | 5 | |||
| Min ON time | tON | 90 | ns | 5 | |||
| Min OFF time | tOFF | 200 | ns | 5 | |||
| Thermal shutdown temperature | TSD | 150 | °C | 5 | |||
| Thermal shutdown hysteresis | THYS | 15 | °C | 5 | |||
| Package thermal resistance, junction-to-ambient | θJA | 44.5 | °C/W | JESD51-2, TA = 25°C, 4-layer PCB per JESD51-7 with thermal via | 4 | ||
| Package thermal resistance, junction-to-case | θJC | 22.1 | °C/W | 4 | |||
| Package thermal resistance, junction-to-board | θJB | 14.1 | °C/W | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | the GND pin. 4) The PCB copper area associated with the LX pin | 11 |
CAD (KiCad official)
- Symbol:
SQ27000SXC - Footprint:
Package_DFN_QFN:DFN-8-1EP_4x4mm_P0.8mm_EP2.5x3.6mm - 3D model: DFN-8(4x4) (KiCad packages3D, STEP)
- 3D model files:
sq27000sxc-etched.step/sq27000sxc-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sq27000sxc.step/sq27000sxc.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Silergy Corp datasheet (14 pp, sha256
bb4812bd2ab805eb, retrieved 2026-11-04, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).