Generated by kicad-footprint-generator · KiCad file format 20260206
SPX29302T5-L
MaxLinear · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · TO-263-5
SPX29302T5-L from MaxLinear, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable input, TTL-compatible. Drive high (>=2.4V) to enable the regulator; drive low (<=0.8V) to place the device in zero-current shutdown. Typical input current is ~20µA when active; up to 750µA at VEN=16V. |
| 2 | VIN | power_in | Input supply voltage. Continuous operating range up to 16V (absolute max 20V for <100ms). A 6.8µF (min) input capacitor is recommended; a 0.1µF ceramic to GND is advised if the source has high AC impedance. |
| 3 | GND | power_in | Ground reference for the regulator. Ground pin current is the quiescent current (typ. 30mA at IOUT=1.5A, ~40mA at 3A). The tab of the TO-263 is connected to GND and provides the primary thermal path (θJC = 3°C/W). |
| 4 | VOUT | power_out | Regulated output. Delivers up to 3A guaranteed with typical dropout of 600mV at 3A. Requires a minimum 10µF aluminum output capacitor for stability across all load conditions; requires a minimum load of 5mA. |
| 5 | ADJ | input | Adjust pin. Feedback node referenced to the internal 1.240V reference (VREF typ). Set VOUT via a resistor divider from VOUT to GND: VOUT = VREF x (1 + R1/R2). R2 recommended between 10kΩ and 47kΩ. Adjust pin bias current is typ. 40nA (max 120nA). |
| 6 | GND | power_in | Package tab (pad 6). the sheet does not name the tab's net; centre lead's net per the package (TO-263/TO-252 tab and centre lead are one piece of lead frame; task master ruling 2026-11-17): pin 3 is GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | TO-263-5 |
| Category | PMIC |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reference Voltage | VREF | 1.228 | 1.24 | 1.252 | V | 2 | |
| Reference Voltage (over operating junction temperature range) | VREF | 1.215 | 1.265 | V | over temperature range (•) | 2 | |
| Reference Voltage (line/load range) | VREF | 1.203 | 1.277 | V | VREF≤VOUT≤(VIN-1), 2.3V≤VIN≤16V, 10mA≤IL≤IFL, TJ<TJMAX | 2 | |
| Line Regulation | 0.06 | 0.5 | % | IOUT=10mA, (VOUT+1V)≤VIN≤16V | 2 | ||
| Load Regulation | 0.2 | 1 | % | VIN=VOUT + 1V, 10mA≤IOUT≤IFL (note 2) | 2 | ||
| Output Voltage Temperature Coefficient | ΔV/ΔT | 20 | 100 | ppm/°C | VOUT temp coefficient (note 6); • over temperature range | 2 | |
| Dropout Voltage at IOUT=100mA (except 1.8V version) | 120 | 300 | mV | Except 1.8V Version (note 3); IOUT=100mA; • over temperature range | 2 | ||
| Dropout Voltage at IOUT=3A (except 1.8V version) | 600 | 800 | mV | Except 1.8V Version (note 3); IOUT=3A; • over temperature range | 2 | ||
| Ground Current | 30 | 60 | mA | IOUT=1.5A; • over temperature range | 2 | ||
| Current Limit | 3 | 4.5 | A | VOUT=0V (note 4) | 2 | ||
| Adjust Pin Bias Current | 40 | 80 | nA | 2 | |||
| Adjust Pin Bias Current (over operating junction temperature range) | 120 | nA | over temperature range (•) | 2 | |||
| Input Logic Voltage Low (OFF) | 0.8 | V | VIN<10V; • over temperature range | 3 | |||
| Input Logic Voltage High (ON) | 2.4 | V | • over temperature range | 3 | |||
| Enable Input Pin Current | 100 | 600 | µA | VEN=16V | 3 | ||
| Enable Input Pin Current (over operating junction temperature range) | 750 | µA | VEN=16V; • over temperature range | 3 | |||
| Enable Input Pin Current | 1 | 2 | µA | VEN=0.8V; max value • over temperature range | 3 | ||
| Regulator Output Current in Shutdown | 10 | 500 | µA | Note 9: VEN ≤ 0.8V, VIN ≤ 16V, VOUT = 0; • over temperature range | 3 | ||
| Input Voltage VIN1 | VIN1 | 20 | V | Note 1: limited duration (<100ms) and duty cycle <1%; maximum continuous supply voltage 16V | 2 | ||
| Storage Temperature | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering, 5 sec) | 260 | °C | Soldering, 5 sec | 2 | |||
| ESD Rating (HBM) | 2 | kV | Human Body Model, all pins except EN | 2 | |||
| ESD Rating (HBM) EN pin | 1 | kV | Human Body Model, En pin | 2 | |||
| Input Voltage Range VIN | VIN | 16 | V | Operating ratings | 2 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | Operating junction temperature range | 2 | |
| Thermal Resistance Junction to Case (TO-263-3, TO-263-5) | θJC | 3 | °C/W | TO-263-3, TO-263-5 junction to case | 2 |
CAD (KiCad official)
- Symbol:
SPX29302T5-L - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
spx29302t5-l-etched.step/spx29302t5-l-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);spx29302t5-l.step/spx29302t5-l.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MaxLinear datasheet (10 pp, sha256
2c39cf8e9906cc98, retrieved 2026-11-17, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).