← Commit history

spx29302t5-l: factory component page (tier=mfr)

Ray ·3587fce143 · ·parent 2258236
3 files changed +20−24
README.md+5−12
@@ -8,11 +8,11 @@ SPX29302T5-L from MaxLinear, in a TO-263-5. Pinout and pin descriptions extracte  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | EN | input | Enable input. TTL-compatible: logic low (<0.8V) shuts the regulator down to <500µA; logic high (>2.4V) turns the regulator on. Approximately 20µA flows through the pin when the regulator is active. |-| 2 | VIN | power_in | Regulator input supply. Operating range up to 16V continuous (20V absolute max for <100ms). A 6.8µF (or larger) input capacitor is recommended, plus 0.1µF ceramic near the pin if the source has high AC impedance. |-| 3 | GND | power_in | Ground / return pin. Also carries the regulator quiescent (ground) current - typically 30mA at IOUT=1.5A and 40mA at IOUT=3A. |-| 4 | VOUT | power_out | Regulator output. Delivers up to 3A with 600mV typical dropout at full load. Requires a minimum 10µF aluminum output capacitor for stability across all load conditions; a tantalum output cap is recommended for faster transient response. |-| 5 | ADJ | input | Adjust / feedback pin for setting output voltage via an external R1/R2 divider from VOUT to GND: VOUT = 1.240V × (1 + R1/R2). Reference voltage is 1.240V typical; adjust-pin bias current is ~40nA typ (120nA max). R2 recommended between 10kΩ and 47kΩ. |+| 1 | EN | input | Enable input, TTL-compatible. Drive high (>=2.4V) to enable the regulator; drive low (<=0.8V) to place the device in zero-current shutdown. Typical input current is ~20µA when active; up to 750µA at VEN=16V. |+| 2 | VIN | power_in | Input supply voltage. Continuous operating range up to 16V (absolute max 20V for <100ms). A 6.8µF (min) input capacitor is recommended; a 0.1µF ceramic to GND is advised if the source has high AC impedance. |+| 3 | GND | power_in | Ground reference for the regulator. Ground pin current is the quiescent current (typ. 30mA at IOUT=1.5A, ~40mA at 3A). The tab of the TO-263 is connected to GND and provides the primary thermal path (θJC = 3°C/W). |+| 4 | VOUT | power_out | Regulated output. Delivers up to 3A guaranteed with typical dropout of 600mV at 3A. Requires a minimum 10µF aluminum output capacitor for stability across all load conditions; requires a minimum load of 5mA. |+| 5 | ADJ | input | Adjust pin. Feedback node referenced to the internal 1.240V reference (VREF typ). Set VOUT via a resistor divider from VOUT to GND: VOUT = VREF x (1 + R1/R2). R2 recommended between 10kΩ and 47kΩ. Adjust pin bias current is typ. 40nA (max 120nA). |  ## Key specifications @@ -27,13 +27,6 @@ SPX29302T5-L from MaxLinear, in a TO-263-5. Pinout and pin descriptions extracte  - `SPX29302T5-L` - `SPX29302T5-L/TR`-- `SPX29302T5-LSPX29301T5-L-3-3/TR`-- `SPX29302T5-LSPX29301T5-L-5-0/TR`-- `SPX29302T5-LSPX29300T-L-1-8/TR`-- `SPX29302T5-LSPX29300T-L-2-5/TR`-- `SPX29302T5-LSPX29300T-L-3-3`-- `SPX29302T5-LSPX29300T-L-3-3/TR`-- `SPX29302T5-LSPX29300T-L-5-0/TR`  ## CAD (KiCad official) 
page.json+6−9
@@ -32,31 +32,31 @@         "number": "1",         "name": "EN",         "type": "input",-        "description": "Enable input. TTL-compatible: logic low (<0.8V) shuts the regulator down to <500µA; logic high (>2.4V) turns the regulator on. Approximately 20µA flows through the pin when the regulator is active."+        "description": "Enable input, TTL-compatible. Drive high (>=2.4V) to enable the regulator; drive low (<=0.8V) to place the device in zero-current shutdown. Typical input current is ~20\u00b5A when active; up to 750\u00b5A at VEN=16V."       },       {         "number": "2",         "name": "VIN",         "type": "power_in",-        "description": "Regulator input supply. Operating range up to 16V continuous (20V absolute max for <100ms). A 6.8µF (or larger) input capacitor is recommended, plus 0.1µF ceramic near the pin if the source has high AC impedance."+        "description": "Input supply voltage. Continuous operating range up to 16V (absolute max 20V for <100ms). A 6.8\u00b5F (min) input capacitor is recommended; a 0.1\u00b5F ceramic to GND is advised if the source has high AC impedance."       },       {         "number": "3",         "name": "GND",         "type": "power_in",-        "description": "Ground / return pin. Also carries the regulator quiescent (ground) current - typically 30mA at IOUT=1.5A and 40mA at IOUT=3A."+        "description": "Ground reference for the regulator. Ground pin current is the quiescent current (typ. 30mA at IOUT=1.5A, ~40mA at 3A). The tab of the TO-263 is connected to GND and provides the primary thermal path (\u03b8JC = 3\u00b0C/W)."       },       {         "number": "4",         "name": "VOUT",         "type": "power_out",-        "description": "Regulator output. Delivers up to 3A with 600mV typical dropout at full load. Requires a minimum 10µF aluminum output capacitor for stability across all load conditions; a tantalum output cap is recommended for faster transient response."+        "description": "Regulated output. Delivers up to 3A guaranteed with typical dropout of 600mV at 3A. Requires a minimum 10\u00b5F aluminum output capacitor for stability across all load conditions; requires a minimum load of 5mA."       },       {         "number": "5",         "name": "ADJ",         "type": "input",-        "description": "Adjust / feedback pin for setting output voltage via an external R1/R2 divider from VOUT to GND: VOUT = 1.240V × (1 + R1/R2). Reference voltage is 1.240V typical; adjust-pin bias current is ~40nA typ (120nA max). R2 recommended between 10kΩ and 47kΩ."+        "description": "Adjust pin. Feedback node referenced to the internal 1.240V reference (VREF typ). Set VOUT via a resistor divider from VOUT to GND: VOUT = VREF x (1 + R1/R2). R2 recommended between 10k\u03a9 and 47k\u03a9. Adjust pin bias current is typ. 40nA (max 120nA)."       }     ],     "provenance": {@@ -120,8 +120,5 @@     "docs/spx29302t5-l-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": {-    "public": true-  }+  ] }\ No newline at end of file
spx29302t5-l.lbr+9−3
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>MaxLinear Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, TO-263-5</description> <packages> <package name="TO-263-5_TabPin6">   <description>6 pads, 16.1 x 10.8 mm. TO-263/D2PAK/DDPAK SMD package</description>@@ -100,6 +100,7 @@ </packages> <symbols> <symbol name="SPX29302T5-L">+  <description>MaxLinear Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, TO-263-5</description>   <wire x1="-12.7" y1="5.08" x2="12.7" y2="5.08" width="0.254" layer="94"/>   <wire x1="12.7" y1="5.08" x2="12.7" y2="-5.08" width="0.254" layer="94"/>   <wire x1="12.7" y1="-5.08" x2="-12.7" y2="-5.08" width="0.254" layer="94"/>@@ -115,7 +116,7 @@ </symbols> <devicesets> <deviceset name="SPX29302T5-L" prefix="U">-  <description></description>+  <description>MaxLinear Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, TO-263-5</description>   <gates>     <gate name="G$1" symbol="SPX29302T5-L" x="0" y="0"/>   </gates>@@ -128,7 +129,12 @@         <connect gate="G$1" pin="ADJ" pad="5"/>         <connect gate="G$1" pin="VOUT" pad="4"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="SPX29302T5-L" constant="no"/>+          <attribute name="MANUFACTURER" value="MaxLinear" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>