3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSP3485EN-MS
MSKSEMI · RS-485 / RS-422 ICs · SOP-8
SP3485EN-MS from MSKSEMI, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: goes high when /RE is low and A - B is at or above -10 mV, and goes low when A - B is at or below -200 mV. |
| 2 | /RE | input | Active-low receiver output enable: RO is high impedance when /RE is high, and driving /RE high with DE low puts the device into low-power shutdown. |
| 3 | DE | input | Active-high driver output enable: the driver outputs are high impedance when DE is low, and driving /RE high with DE low puts the device into low-power shutdown. |
| 4 | DI | input | Driver input: with DE high, a low on DI forces the non-inverting output low and the inverting output high, and a high on DI forces the non-inverting output high and the inverting output low. |
| 5 | GND | power_in | Ground; the reference point for all voltages on the device. |
| 6 | A | bidirectional | Non-inverting receiver input and non-inverting driver output on the RS-485 bus. |
| 7 | B | bidirectional | Inverting receiver input and inverting driver output on the RS-485 bus. |
| 8 | VCC | power_in | Positive supply, specified for 3.0 V to 5.5 V operation, with an absolute maximum supply voltage of 7 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MSKSEMI |
| Package | SOP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 7 | V | 4 | |||
| Control input voltage /RE, DE, DI | -0.3 | V | 4 | ||||
| Receiver input voltage A, B | -15 | 15 | V | 4 | |||
| Receiver output voltage RO | -0.3 | V | 4 | ||||
| Operating temperature range | -40 | 125 | ℃ | 4 | |||
| Storage temperature range | -60 | 150 | ℃ | 4 | |||
| Lead temperature | 300 | ℃ | 4 | ||||
| Continuous power dissipation (SOP8) | 470 | mW | 4 | ||||
| Differential driver output (no load) | VOD1 | 3 | 5.5 | V | No load | 5 | |
| Differential driver output | VOD2 | 1.5 | V | Figure 2, RL = 54 Ω, VCC=3.3V | 5 | ||
| Change in magnitude of driver differential output voltage | ΔVOD | 0.2 | V | Figure 2, RL = 54 Ω | 5 | ||
| Driver common-mode output voltage | VOC | 3 | V | Figure 2, RL = 54 Ω | 5 | ||
| Change in magnitude of common-mode output voltage | ΔVOC | 0.2 | V | Figure 2, RL = 54 Ω | 5 | ||
| Input high voltage | VIH | 2 | V | DE, DI, /RE | 5 | ||
| Input low voltage | VIL | 0.8 | V | DE, DI, /RE | 5 | ||
| Logic input current | IIN1 | -2 | 2 | μA | DE, DI, /RE | 5 | |
| Output short-circuit current, short-circuit to high | IOSD1 | 250 | mA | short-circuit to 0V~12V | 5 | ||
| Output short-circuit current, short-circuit to low | IOSD2 | -250 | mA | short-circuit to -7V~0V | 5 | ||
| Input current (A, B) | IIN2 | 125 | μA | DE = 0 V, VCC=0 or 3.3/5V, VIN = 12 V | 5 | ||
| Input current (A, B) | IIN2 | -100 | μA | DE = 0 V, VCC=0 or 3.3/5V, VIN = -7 V | 5 | ||
| Positive input threshold voltage | VIT+ | -10 | mV | -7V≦VCM≦ 12V | 6 | ||
| Reverse input threshold voltage | VIT- | -200 | mV | -7V≦VCM≦ 12V | 6 | ||
| Input hysteresis voltage | Vhys | 10 | 30 | mV | -7V≦VCM≦ 12V | 6 | |
| Receiver output low voltage | VOL | 0.4 | V | IOUT = +2.5mA, VID = -200 mV | 6 | ||
| Three-state output current at receiver | IOZR | -1 | 1 | μA | 0.4 V < VO < 2.4 V | 6 | |
| Receiver input resistance | RIN | 96 | kΩ | -7V≦VCM≦ 12V | 6 | ||
| Receiver short-circuit output current | IOSR | 8 | 90 | mA | 0 V≤VO≤VCC | 6 | |
| Supply current | ICC1 | 240 | 650 | μA | /RE=0V, DE = 0 V, VCC=3.3V | 6 | |
| Supply current | ICC1 | 270 | 750 | μA | /RE=0V, DE = 0 V, VCC=5V | 6 | |
| Supply current | ICC2 | 250 | 650 | μA | /RE=VCC, DE=VCC, VCC=3.3V | 6 | |
| Supply current | ICC2 | 280 | 750 | μA | /RE=VCC, DE=VCC, VCC=5V | 6 | |
| Shutdown current | ISHDN | 0.2 | 10 | μA | /RE=VCC, DE=0V, VCC=3.3V | 6 | |
| Driver differential output delay | tDD | 20 | 40 | ns | RL = 60 Ω, CL1=CL2=100pF (figure 3, 4) | 7 | |
| Driver differential output transition time | tTD | 12 | 28 | ns | 7 | ||
| Driver propagation delay from low to high | tPLH | 20 | 40 | ns | RL = 27 Ω (figure 3, 4) | 7 | |
| Driver propagation delay from high to low | tPHL | 20 | 40 | ns | 7 | ||
| /tPLH-tPHL/ driver propagation delay skew | tPDS | 1 | 8 | ns | 7 | ||
| Driver enable to output high | tPZH | 55 | ns | RL = 110Ω (figure 5, 6) | 7 | ||
| Driver enable to output low | tPZL | 55 | ns | 7 | |||
| Driver disable time from low | tPLZ | 85 | ns | RL = 110Ω (figure 5, 6) | 7 | ||
| Driver disable time from high | tPHZ | 85 | ns | 7 | |||
| In shutdown mode, enable to output high | tDSH | 20 | 100 | ns | RL = 110Ω (figure 5, 6) | 7 | |
| In shutdown mode, enable to output low | tDSL | 20 | 100 | ns | RL = 110Ω (figure 5, 6) | 7 | |
| Receiver input to output from low to high | tRPLH | 60 | ns | CL=15pF, Figure 7 & Figure 8 | 7 | ||
| Receiver input to output from high to low | tRPHL | 60 | ns | 7 | |||
| /tRPLH − tRPHL/ receiver propagation delay skew | tRPDS | 3 | 10 | ns | 8 | ||
| Receiver enable to output low | tRPZL | 15 | 40 | ns | CL=15pF, Figure 7 & Figure 8 | 8 | |
| Receiver enable to output high | tRPZH | 15 | 40 | ns | CL=15pF, Figure 7 & Figure 8 | 8 | |
| Receiver disable time from low | tPRLZ | 25 | 55 | ns | CL=15pF, Figure 7 & Figure 8 | 8 | |
| Receiver disable time from high | tPRHZ | 25 | 55 | ns | CL=15pF, Figure 7 & Figure 8 | 8 | |
| In shutdown mode, enable to output high | tRPSH | 150 | 500 | ns | CL=15pF, Figure 7 & Figure 8 | 8 | |
| In shutdown mode, enable to output low | tRPSL | 150 | 500 | ns | CL=15pF, Figure 7 & Figure 8 | 8 | |
| Time to shutdown | tSHDN | 50 | 300 | ns | NOTE2 | 8 |
CAD (KiCad official)
- Symbol:
SP3485EN-MS - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
sp3485en-ms-etched.step/sp3485en-ms-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sp3485en-ms.step/sp3485en-ms.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MSKSEMI datasheet (18 pp, sha256
2f8e488a700d89d9, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).