main
Ray
Publish 0.1.0
2b30509
SN75LBC182P
Texas Instruments · RS-485 / RS-422 ICs · PDIP-8
SN75LBC182P from Texas Instruments, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | R | output | Receiver output: high for VID ≥ 0.2 V, low for VID ≤ −0.2 V, and high when the bus inputs are open (fail-safe); high-impedance when RE is high. |
| 2 | RE | input | Active-low receiver enable input; the receiver output is high-impedance when RE is held high. |
| 3 | DE | input | Active-high driver enable input; the driver outputs A and B are high-impedance when DE is low. |
| 4 | D | input | Driver input; with DE high, a high on D drives A high and B low, and a low on D drives A low and B high. |
| 5 | GND | power_in | Device ground; all voltages except differential bus voltages are referenced to the network ground terminal. |
| 6 | A | bidirectional | Non-inverting differential bus I/O; voltage at any bus terminal is limited to −7 V to 12 V in recommended operation and −15 V to 15 V absolute maximum. |
| 7 | B | bidirectional | Inverting differential bus I/O; voltage at any bus terminal is limited to −7 V to 12 V in recommended operation and −15 V to 15 V absolute maximum. |
| 8 | VCC | power_in | Device supply voltage, 4.75 V to 5.25 V recommended (5 V nominal), with 7 V absolute maximum. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage, VCC | VCC | 4.75 | 5 | 5.25 | V | 5 | |
| Voltage at any bus I/O terminal (separately or common mode) | VI or VIC | -7 | 12 | V | 5 | ||
| High-level input voltage, D, DE, RE | VIH | 2 | V | 5 | |||
| Low-level input voltage | VIL | 0.8 | V | 5 | |||
| Differential input voltage | VID | -12 | 12 | V | Differential input/output bus voltage measured at A with respect to B | 5 | |
| Output current, driver | IO | -60 | 60 | mA | Driver | 5 | |
| Output current, receiver | IO | -8 | 4 | mA | Receiver | 5 | |
| Operating free-air temperature, SN75LBC182 | TA | 0 | 70 | °C | SN75LBC182 | 5 | |
| Supply voltage range | VCC | -0.5 | 7 | V | With respect to network ground | 5 | |
| Voltage range at any bus terminal (A or B) | VI | -15 | 15 | V | 5 | ||
| Input voltage (D, DE, R or RE) | VI | -0.3 | 7 | V | 5 | ||
| Receiver output current | IO | -20 | 20 | mA | 5 | ||
| Continuous total power dissipation, P (PDIP) package power rating | 1150 | mW | P package, TA ≤ 25°C | 5 | |||
| Junction-to-ambient thermal resistance, P (PDIP) 8-pin | RθJA | 84.3 | °C/W | P (PDIP) package, 8 pins | 6 | ||
| Driver input clamp voltage | VIK | -1.5 | V | II = −18 mA | 6 | ||
| Driver output voltage | VO | 0 | V | IO = 0; printed max is VCC | 6 | ||
| Differential output voltage | /VOD/ | 1.5 | 2.2 | V | RL = 54 Ω, See Figure 6-1; printed max is VCC | 6 | |
| Differential output voltage with common-mode loading | /VOD/ | 1.5 | 2.2 | V | Vtest = −7 V to 12 V, See Figure 6-2; printed max is VCC | 6 | |
| Change in magnitude of differential output voltage | ΔVOD | -0.2 | 0.2 | V | See Figure 6-1 | 6 | |
| Steady-state common-mode output voltage | VOC(SS) | 1 | 3 | V | 6 | ||
| Change in steady-state common-mode output voltage | ΔVOC(SS) | -0.2 | 0.2 | V | See Figure 6-1 and Figure 6-4 | 6 | |
| Peak-to-peak change in common-mode output voltage during state transitions | VOC(PP) | 0.8 | V | 6 | |||
| High-level input current (D, DE) | IIH | 50 | μA | VI = 2.4 V | 6 | ||
| Low-level input current (D, DE) | IIL | -50 | μA | VI = 0.4 V | 6 | ||
| Short-circuit output current | IOS | -250 | 250 | mA | VO = −7 V to 12 V | 6 | |
| Supply current, SN75LBC182 (driver enabled) | ICC | 12 | 25 | mA | No load, DE at VCC, RE at VCC | 6 | |
| Positive-going input threshold voltage | VIT+ | 0.2 | V | 6 | |||
| Negative-going input threshold voltage | VIT− | -0.2 | V | 6 | |||
| Hysteresis voltage (VIT+ − VIT-) | Vhys | 70 | mV | 6 | |||
| Enable-input clamp voltage | VIK | -1.5 | V | II = −18 mA | 6 | ||
| High-level output voltage | VOH | 2.8 | V | VID = 200 mV, IO = −8 mA, See Figure 6-7 | 6 | ||
| Low-level output voltage | VOL | 0.4 | V | VID = 200 mV, IO = 4 mA, See Figure 6-7 | 6 | ||
| High-impedance-state output current | IOZ | -1 | 1 | μA | VO = 0.4 to 2.4 V | 7 | |
| Bus input current | II | 250 | μA | VIH = 12 V, VCC = 5 V, other input at 0 V | 7 | ||
| Bus input current | II | -200 | μA | VIH = −7 V, VCC = 5 V, other input at 0 V | 7 | ||
| High-level input current (RE) | IIH | 50 | μA | VIH = 2 V | 7 | ||
| Low-level input current (RE) | IIL | -50 | μA | VIL = 0.8 V | 7 | ||
| Supply current, receiver enabled with DE low and RE low | ICC | 3.5 | mA | No load, DE at 0 V, RE at 0 V | 7 | ||
| Supply current, DE low and RE high (disabled) | ICC | 175 | 250 | μA | No load, DE at 0 V, RE at VCC | 7 | |
| Differential output signal rise time | tr | 0.25 | 0.72 | 1.2 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 |
| Differential output signal fall time | tf | 0.25 | 0.73 | 1.2 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 |
| Propagation delay time, low-to-high-level output | tPLH | 1.3 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 | ||
| Propagation delay time, high-to-low-level output | tPHL | 1.3 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 | ||
| Pulse skew (tPHL − tPLH) | tsk(p) | 0.075 | 0.15 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 | |
| Output enable time to high level | tPZH | 3.5 | μs | RL = 110 Ω, See Figure 6-5 | 7 | ||
| Output disable time from high level | tPHZ | 3.5 | μs | RL = 110 Ω, See Figure 6-5 | 7 | ||
| Output enable time to low level | tPZL | 3.5 | μs | RL = 110 Ω, See Figure 6-6 | 7 | ||
| Output disable time from low level | tPLZ | 3.5 | μs | RL = 110 Ω, See Figure 6-6 | 7 | ||
| Differential output signal rise time (receiver) | tr | 20 | ns | CL = 50 pF, See Figure 6-7 | 7 | ||
| Differential output signal fall time (receiver) | tf | 20 | ns | CL = 50 pF, See Figure 6-7 | 7 | ||
| Propagation delay time, low-to-high-level output (receiver) | tPLH | 150 | ns | CL = 50 pF, See Figure 6-7 | 7 | ||
| Propagation delay time, high-to-low-level output (receiver) | tPHL | 150 | ns | CL = 50 pF, See Figure 6-7 | 7 | ||
| Output enable time to high level (receiver) | tPZH | 100 | ns | See Figure 6-8 | 7 | ||
| Output enable time to low level (receiver) | tPZL | 100 | ns | See Figure 6-8 | 7 | ||
| Output disable time from high level (receiver) | tPHZ | 100 | ns | See Figure 6-8 | 7 | ||
| Output disable time from low level (receiver) | tPLZ | 100 | ns | See Figure 6-8 | 7 | ||
| Pulse skew /tPHL − tPLH/ (receiver) | tsk(p) | 50 | ns | 7 |
CAD (KiCad official)
- Symbol:
SN75LBC182P - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: PDIP-8 (KiCad packages3D, STEP)
- 3D model files:
sn75lbc182p-etched.step/sn75lbc182p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn75lbc182p.step/sn75lbc182p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (24 pp, sha256
f83ef4d9e449a65f, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SN75LBC182P
**Texas Instruments** · RS-485 / RS-422 ICs · PDIP-8
SN75LBC182P from Texas Instruments, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | R | output | Receiver output: high for VID ≥ 0.2 V, low for VID ≤ −0.2 V, and high when the bus inputs are open (fail-safe); high-impedance when RE is high. |
| 2 | RE | input | Active-low receiver enable input; the receiver output is high-impedance when RE is held high. |
| 3 | DE | input | Active-high driver enable input; the driver outputs A and B are high-impedance when DE is low. |
| 4 | D | input | Driver input; with DE high, a high on D drives A high and B low, and a low on D drives A low and B high. |
| 5 | GND | power_in | Device ground; all voltages except differential bus voltages are referenced to the network ground terminal. |
| 6 | A | bidirectional | Non-inverting differential bus I/O; voltage at any bus terminal is limited to −7 V to 12 V in recommended operation and −15 V to 15 V absolute maximum. |
| 7 | B | bidirectional | Inverting differential bus I/O; voltage at any bus terminal is limited to −7 V to 12 V in recommended operation and −15 V to 15 V absolute maximum. |
| 8 | VCC | power_in | Device supply voltage, 4.75 V to 5.25 V recommended (5 V nominal), with 7 V absolute maximum. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-8 |
| Category | Interface |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage, VCC | VCC | 4.75 | 5 | 5.25 | V | | 5 |
| Voltage at any bus I/O terminal (separately or common mode) | VI or VIC | -7 | | 12 | V | | 5 |
| High-level input voltage, D, DE, RE | VIH | 2 | | | V | | 5 |
| Low-level input voltage | VIL | | | 0.8 | V | | 5 |
| Differential input voltage | VID | -12 | | 12 | V | Differential input/output bus voltage measured at A with respect to B | 5 |
| Output current, driver | IO | -60 | | 60 | mA | Driver | 5 |
| Output current, receiver | IO | -8 | | 4 | mA | Receiver | 5 |
| Operating free-air temperature, SN75LBC182 | TA | 0 | | 70 | °C | SN75LBC182 | 5 |
| Supply voltage range | VCC | -0.5 | | 7 | V | With respect to network ground | 5 |
| Voltage range at any bus terminal (A or B) | VI | -15 | | 15 | V | | 5 |
| Input voltage (D, DE, R or RE) | VI | -0.3 | | 7 | V | | 5 |
| Receiver output current | IO | -20 | | 20 | mA | | 5 |
| Continuous total power dissipation, P (PDIP) package power rating | | | | 1150 | mW | P package, TA ≤ 25°C | 5 |
| Junction-to-ambient thermal resistance, P (PDIP) 8-pin | RθJA | | 84.3 | | °C/W | P (PDIP) package, 8 pins | 6 |
| Driver input clamp voltage | VIK | | | -1.5 | V | II = −18 mA | 6 |
| Driver output voltage | VO | 0 | | | V | IO = 0; printed max is VCC | 6 |
| Differential output voltage | /VOD/ | 1.5 | 2.2 | | V | RL = 54 Ω, See Figure 6-1; printed max is VCC | 6 |
| Differential output voltage with common-mode loading | /VOD/ | 1.5 | 2.2 | | V | Vtest = −7 V to 12 V, See Figure 6-2; printed max is VCC | 6 |
| Change in magnitude of differential output voltage | ΔVOD | -0.2 | | 0.2 | V | See Figure 6-1 | 6 |
| Steady-state common-mode output voltage | VOC(SS) | 1 | | 3 | V | | 6 |
| Change in steady-state common-mode output voltage | ΔVOC(SS) | -0.2 | | 0.2 | V | See Figure 6-1 and Figure 6-4 | 6 |
| Peak-to-peak change in common-mode output voltage during state transitions | VOC(PP) | | | 0.8 | V | | 6 |
| High-level input current (D, DE) | IIH | | | 50 | μA | VI = 2.4 V | 6 |
| Low-level input current (D, DE) | IIL | -50 | | | μA | VI = 0.4 V | 6 |
| Short-circuit output current | IOS | -250 | | 250 | mA | VO = −7 V to 12 V | 6 |
| Supply current, SN75LBC182 (driver enabled) | ICC | | 12 | 25 | mA | No load, DE at VCC, RE at VCC | 6 |
| Positive-going input threshold voltage | VIT+ | | | 0.2 | V | | 6 |
| Negative-going input threshold voltage | VIT− | -0.2 | | | V | | 6 |
| Hysteresis voltage (VIT+ − VIT-) | Vhys | | 70 | | mV | | 6 |
| Enable-input clamp voltage | VIK | | | -1.5 | V | II = −18 mA | 6 |
| High-level output voltage | VOH | 2.8 | | | V | VID = 200 mV, IO = −8 mA, See Figure 6-7 | 6 |
| Low-level output voltage | VOL | | | 0.4 | V | VID = 200 mV, IO = 4 mA, See Figure 6-7 | 6 |
| High-impedance-state output current | IOZ | -1 | | 1 | μA | VO = 0.4 to 2.4 V | 7 |
| Bus input current | II | | | 250 | μA | VIH = 12 V, VCC = 5 V, other input at 0 V | 7 |
| Bus input current | II | -200 | | | μA | VIH = −7 V, VCC = 5 V, other input at 0 V | 7 |
| High-level input current (RE) | IIH | | | 50 | μA | VIH = 2 V | 7 |
| Low-level input current (RE) | IIL | -50 | | | μA | VIL = 0.8 V | 7 |
| Supply current, receiver enabled with DE low and RE low | ICC | | | 3.5 | mA | No load, DE at 0 V, RE at 0 V | 7 |
| Supply current, DE low and RE high (disabled) | ICC | | 175 | 250 | μA | No load, DE at 0 V, RE at VCC | 7 |
| Differential output signal rise time | tr | 0.25 | 0.72 | 1.2 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 |
| Differential output signal fall time | tf | 0.25 | 0.73 | 1.2 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 |
| Propagation delay time, low-to-high-level output | tPLH | | | 1.3 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 |
| Propagation delay time, high-to-low-level output | tPHL | | | 1.3 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 |
| Pulse skew (tPHL − tPLH) | tsk(p) | | 0.075 | 0.15 | μs | RL = 54 Ω, CL = 50 pF, See Figure 6-3 | 7 |
| Output enable time to high level | tPZH | | | 3.5 | μs | RL = 110 Ω, See Figure 6-5 | 7 |
| Output disable time from high level | tPHZ | | | 3.5 | μs | RL = 110 Ω, See Figure 6-5 | 7 |
| Output enable time to low level | tPZL | | | 3.5 | μs | RL = 110 Ω, See Figure 6-6 | 7 |
| Output disable time from low level | tPLZ | | | 3.5 | μs | RL = 110 Ω, See Figure 6-6 | 7 |
| Differential output signal rise time (receiver) | tr | | | 20 | ns | CL = 50 pF, See Figure 6-7 | 7 |
| Differential output signal fall time (receiver) | tf | | | 20 | ns | CL = 50 pF, See Figure 6-7 | 7 |
| Propagation delay time, low-to-high-level output (receiver) | tPLH | | | 150 | ns | CL = 50 pF, See Figure 6-7 | 7 |
| Propagation delay time, high-to-low-level output (receiver) | tPHL | | | 150 | ns | CL = 50 pF, See Figure 6-7 | 7 |
| Output enable time to high level (receiver) | tPZH | | | 100 | ns | See Figure 6-8 | 7 |
| Output enable time to low level (receiver) | tPZL | | | 100 | ns | See Figure 6-8 | 7 |
| Output disable time from high level (receiver) | tPHZ | | | 100 | ns | See Figure 6-8 | 7 |
| Output disable time from low level (receiver) | tPLZ | | | 100 | ns | See Figure 6-8 | 7 |
| Pulse skew /tPHL − tPLH/ (receiver) | tsk(p) | | | 50 | ns | | 7 |
## CAD (KiCad official)
- Symbol: `SN75LBC182P`
- Footprint: `Package_DIP:DIP-8_W7.62mm`
- 3D model: PDIP-8 (KiCad packages3D, STEP)
- 3D model files: `sn75lbc182p-etched.step` / `sn75lbc182p-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sn75lbc182p.step` / `sn75lbc182p.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/sn75lbc182.pdf) (24 pp, sha256 `f83ef4d9e449a65f`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/sn75lbc182p-datasheet.pdf)