Generated by kicad-footprint-generator · KiCad file format 20260206
SN75LBC176P
Texas Instruments · RS-485 / RS-422 ICs · PDIP-8
SN75LBC176P from Texas Instruments, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | R | output | Logic output carrying RS-485 receive data; it goes high impedance when the receiver is disabled with RE high. |
| 2 | RE | input | Active-low receiver enable/disable input; the receiver is enabled when RE is low and its output is high impedance when RE is high. |
| 3 | DE | input | Active-high driver enable/disable input; the driver outputs are high impedance when DE is low. |
| 4 | D | input | Logic input for RS-485 driver data; with DE high, A is driven high and B low when D is high, and the reverse when D is low. |
| 5 | GND | power_in | Network ground terminal; all voltages except the differential bus voltage are referenced to this pin. |
| 6 | A | bidirectional | Non-inverting RS-485 bus pin; recommended voltage at any bus terminal is -7 V to 12 V, with differential voltage measured at A with respect to B. |
| 7 | B | bidirectional | Inverting RS-485 bus pin; recommended voltage at any bus terminal is -7 V to 12 V, with differential voltage measured at A with respect to B. |
| 8 | VCC | power_in | 5-V supply voltage; recommended range is 4.75 V to 5.25 V, with absolute maximum of 7 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 7 | V | 4 | |||
| Voltage range at any bus terminal | -10 | 15 | V | 4 | |||
| Input voltage (D, DE, R, RE) | VI | -0.3 | V | Upper limit printed as VCC + 0.5 V | 4 | ||
| Receiver output current | IO | -10 | 10 | mA | Receiver | 4 | |
| Storage temperature range | Tstg | -65 | 150 | °C | 4 | ||
| Supply voltage | VCC | 4.75 | 5 | 5.25 | V | 4 | |
| Voltage at any bus terminal (separately or common mode) | VI or VIC | -7 | 12 | V | 4 | ||
| High-level input voltage | VIH | 2 | V | D, DE, and RE | 4 | ||
| Low-level input voltage | VIL | 0.8 | V | D, DE, and RE | 4 | ||
| Differential input voltage | VID | -12 | 12 | V | 4 | ||
| High-level output current, driver | IOH | -60 | mA | Driver | 4 | ||
| High-level output current, receiver | IOH | -400 | µA | Receiver | 4 | ||
| Low-level output current, driver | IOL | 60 | mA | Driver | 4 | ||
| Low-level output current, receiver | IOL | 8 | mA | Receiver | 4 | ||
| Junction temperature | TJ | 140 | °C | 4 | |||
| Operating free-air temperature (SN75LBC176) | TA | 0 | 70 | °C | 4 | ||
| Power rating (P package) | 840 | mW | TA < 25°C | 5 | |||
| Input clamp voltage | VIK | -1.5 | V | II = -18 mA | 5 | ||
| Output voltage | VO | 0 | 6 | V | IO = 0 | 5 | |
| Differential output voltage | /VOD1/ | 1.5 | 6 | V | IO = 0 | 5 | |
| Differential output voltage (RL = 54 Ω) | /VOD2/ | 1.5 | 5 | V | RL = 54 Ω, See Figure 7-1 | 5 | |
| Differential output voltage (test termination) | /VOD3/ | 1.5 | 5 | V | Vtest = -7 V to 12 V, See Figure 2 | 5 | |
| Change in magnitude of differential output voltage | Δ/VOD/ | -0.2 | 0.2 | V | RL = 54 Ω or 100 Ω, See Figure 7-1 | 5 | |
| Common-mode output voltage | VOC | -1 | 3 | V | 5 | ||
| Change in magnitude of common-mode output voltage | Δ/VOC/ | -0.2 | 0.2 | V | 5 | ||
| Output current (output disabled) | IO | 1 | mA | Output disabled; VO = 12 V | 5 | ||
| Output current (output disabled) | IO | -0.8 | mA | Output disabled; VO = -7 V | 5 | ||
| High-level input current | IIH | -100 | µA | VI = 2.4 V | 5 | ||
| Low-level input current | IIL | -100 | µA | VI = 0.4 V | 5 | ||
| Short circuit output current | IOS | -250 | mA | VO = −7 V | 6 | ||
| Short circuit output current | IOS | -150 | mA | VO = 0 | 6 | ||
| Short circuit output current | IOS | 250 | mA | VO = VCC | 6 | ||
| Supply current (receiver disabled and driver enabled) | ICC | 1.5 | mA | VI = 0 or VCC, No load; receiver disabled and driver enabled | 6 | ||
| Supply current (receiver and driver disabled) | ICC | 0.2 | mA | VI = 0 or VCC, No load; receiver and driver disabled | 6 | ||
| Positive-going input threshold voltage | VIT+ | 0.2 | V | VO = 2.7 V, IO = -0.4 mA | 8 | ||
| Negative-going input threshold voltage | VIT- | -0.2 | V | VO = 0.5 V, IO = 8 mA | 8 | ||
| Enable-input clamp voltage | VIK | -1.5 | V | II = -18 mA | 8 | ||
| High-level output voltage | VOH | 2.7 | V | VID = 200 mV, IOH = -400 µA, See Figure 7-6 | 8 | ||
| Low-level output voltage | VOL | 0.45 | V | VID = −200 mV, IOL = 8 mA, See Figure 7-6 | 8 | ||
| High-impedance-state output current | IOZ | -20 | 20 | µA | VO = 0.4 V to 2.4 V | 8 | |
| Line input current | II | 1 | mA | Other input = 0 V; VI = 12 V | 8 | ||
| Line input current | II | -0.8 | mA | Other input = 0 V; VI = -7 V | 8 | ||
| High-level enable-input current | IIH | -100 | µA | VIH = 2.7 V | 8 | ||
| Low-level enable-input current | IIL | -100 | µA | VIL = 0.4 V | 8 | ||
| Supply current (receiver enabled and driver disabled) | ICC | 3.9 | mA | VI = 0 or VCC, No load; receiver enabled and driver disabled | 8 | ||
| Supply current (receiver and driver disabled) | ICC | 0.2 | mA | VI = 0 or VCC, No load; receiver and driver disabled | 8 | ||
| Differential output delay time | td(OD) | 8 | 25 | ns | RL = 54 Ω, CL = 50 pF, See Figure 7-3 | 7 | |
| Output enable time to high level | tPZH | 35 | ns | RL = 110 Ω, See Figure 7-4 | 7 | ||
| Output enable time to low level | tPZL | 35 | ns | RL = 110 Ω, See Figure 7-5 | 7 | ||
| Output disable time from high level | tPHZ | 60 | ns | RL = 110 Ω, See Figure 7-4 | 7 | ||
| Output disable time from low level | tPLZ | 35 | ns | RL = 110 Ω, See Figure 7-5 | 7 | ||
| Propagation delay time, low- to high-level single-ended output | tPLH | 11 | 33 | ns | CL = 15 pF; VID = -1.5 V to 1.5 V, See Figure 7-7 | 8 | |
| Propagation delay time, high- to low-level single-ended output | tPHL | 11 | 33 | ns | CL = 15 pF; VID = -1.5 V to 1.5 V, See Figure 7-7 | 8 | |
| Pulse skew (/tPLH, tPHL/) | tsk(p) | 3 | 6 | ns | CL = 15 pF | 8 | |
| Output enable time to high level | tPZH | 35 | ns | CL = 15 pF, See Figure 7-8 | 8 | ||
| Output enable time to low level | tPZL | 30 | ns | CL = 15 pF, See Figure 7-8 | 8 | ||
| Output disable time from high level | tPHZ | 35 | ns | CL = 15 pF, See Figure 7-8 | 8 | ||
| Output disable time from low level | tPLZ | 30 | ns | CL = 15 pF, See Figure 7-8 | 8 | ||
| Junction-to-ambient thermal resistance (P package) | RθJA | 65.6 | °C/W | P package, 8 pins | 5 | ||
| Junction-to-case (top) thermal resistance (P package) | RθJC(top) | 54.6 | °C/W | P package, 8 pins | 5 |
CAD (KiCad official)
- Symbol:
SN75LBC176P - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: PDIP-8 (KiCad packages3D, STEP)
- 3D model files:
sn75lbc176p-etched.step/sn75lbc176p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn75lbc176p.step/sn75lbc176p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (29 pp, sha256
a708c623b041ca86, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).