Generated by kicad-footprint-generator · KiCad file format 20260206
SN75176N
HGSEMI · RS-485 / RS-422 ICs · DIP-8
SN75176N from HGSEMI, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: with RE low, RO is driven high when A-B is at or above -50 mV and low when A-B is at or below -200 mV. |
| 2 | RE | input | Receiver output enable, active low: RO is enabled when RE is low and goes high-impedance when RE is high, and with RE high and DE low the device enters low-power shutdown. |
| 3 | DE | input | Driver output enable, active high: the driver outputs are enabled when DE is high and high-impedance when DE is low, and with RE high and DE low the device enters low-power shutdown. |
| 4 | DI | input | Driver input: with DE high, a low on DI forces the non-inverting output low and the inverting output high, and a high on DI forces the non-inverting output high and the inverting output low. |
| 5 | GND | power_in | Ground reference for the device. |
| 6 | A | bidirectional | Receiver non-inverting input and driver non-inverting output on the RS-485 bus, with enhanced ESD protection (HBM ±2 kV, IEC 61000-4-2 contact and air discharge ±8 kV). |
| 7 | B | bidirectional | Receiver inverting input and driver inverting output on the RS-485 bus, with enhanced ESD protection (HBM ±2 kV, IEC 61000-4-2 contact and air discharge ±8 kV). |
| 8 | VCC | power_in | Positive supply, specified for 4.5 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | DIP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 4.5 | 5.5 | V | 4 | ||
| Differential driver output (no load) | VOD1 | 1.5 | 5 | V | 图 4 | 4 | |
| Differential driver output | VOD2 | 1.5 | 5 | V | 图 4,R=27Ω(RS-485) | 4 | |
| Change in magnitude of differential output voltage | ∆VOD | 0.2 | V | 图 4,R=50Ω或 R=27Ω | 4 | ||
| Driver common-mode output voltage | VOC | 1 | 3 | V | 图 4,R=50Ω或 R=27Ω | 4 | |
| Change in magnitude of common-mode voltage | ∆VOC | 0.2 | V | 图 4,R=50Ω或 R=27Ω | 4 | ||
| Input high voltage | VIH1 | 2 | V | DE,DI,/RE | 4 | ||
| Input low voltage | VIL1 | 0.8 | V | DE,DI,/RE | 4 | ||
| DI input hysteresis | VHYS | 100 | mV | 4 | |||
| Input current (A,B), half-duplex, maximum | IIN4 | 500 | µA | DE=GND, VCC=GND or 5.5V, VIN=12V | 4 | ||
| Input current (A,B), half-duplex, minimum | IIN4 | -500 | µA | DE=GND, VCC=GND or 5.5V, VIN=-7V | 4 | ||
| Driver short-circuit output current | IOSD | -250 | mA | -7V≦VOUT≦VCC | 4 | ||
| Driver short-circuit output current | IOSD | 250 | mA | 0V≦VOUT≦12V | 4 | ||
| Driver short-circuit output current | IOSD | -25 | 25 | mA | 0V≦VOUT≦VCC | 4 | |
| Receiver differential threshold voltage | VTH | -200 | -110 | -50 | mV | -7V≦VCM≦12V | 4 |
| Receiver input hysteresis | ∆VTH | 30 | mV | 4 | |||
| Receiver output low voltage | VOL | 0.4 | V | IO=4mA, VID=-200mV | 4 | ||
| Receiver tri-state output current | IOZR | -1 | 1 | µA | 0.4V≦VO≦2.4V | 4 | |
| Receiver input resistance | RIN | 12 | KΩ | -7V≦VCM≦12V | 4 | ||
| Receiver output short-circuit current | IOSR | 7 | 95 | mA | 0V≦VRO≦VCC | 4 | |
| Quiescent supply current | ICC | 500 | 900 | µA | 无负载, /RE=DI=VCC, DE=VCC | 4 | |
| Quiescent supply current | ICC | 400 | 600 | µA | 无负载, /RE=DI=GND, DE=GND | 4 | |
| Shutdown mode current | ISHDN | 20 | 30 | µA | DE=GND,/RE=VCC,DI=VCCorGND | 4 | |
| Thermal shutdown temperature (junction) | TSHDN | 120 | ℃ | 芯片结温 | 4 | ||
| ESD HBM (A/B pins) | -2 | 2 | kV | HBM 人体模式 | 4 | ||
| ESD MM (A/B pins) | -800 | 800 | V | MM 机器模式 | 4 | ||
| ESD contact discharge (A/B pins) | -8 | 8 | kV | 接触放电 IEC 61000-4-2 | 4 | ||
| ESD air discharge (A/B pins) | -8 | 8 | kV | 空气放电 IEC 61000-4-2 | 4 | ||
| Driver input to output propagation delay, low-to-high | TDPLH | 20 | 40 | ns | 图6和8,RDIFF=54Ω,CL1=CL2=100pF | 5 | |
| Driver input to output propagation delay, high-to-low | TDPHL | 20 | 40 | ns | 图6和8,RDIFF=54Ω,CL1=CL2=100pF | 5 | |
| Driver output skew /tDPLH - tDPHL/ | TDHKEW | -10 | -3 | 10 | ns | 图6和8,RDIFF=54Ω,CL1=CL2=100pF | 5 |
| Driver rise or fall time | tDR, tDF | 14 | 25 | ns | 图6和8,RDIFF=54Ω,CL1=CL2=100pF | 5 | |
| Maximum data rate | FMAX | 10 | Mbps | 5 | |||
| Driver enable to output high | TDZH | 150 | ns | 图7和9,CL=100pF S2关闭 | 5 | ||
| Driver enable to output low | TDZL | 150 | ns | 图7和9,CL=100pF S1关闭 | 5 | ||
| Driver low to disable time | TDLZ | 100 | ns | 图7和9,CL=15pF S1关闭 | 5 | ||
| Driver high to disable time | TDHZ | 100 | ns | 图7和9,CL=15pF S2关闭 | 5 | ||
| Receiver input to output propagation delay (low-to-high and high-to-low) | TRPLH, TRPHL | 50 | ns | 图10和12,IVIDI≥2.0V VID≦15ns | 5 | ||
| Receiver skew /tRPLH - tRPHL/ | TRSKD | -10 | 0 | 10 | ns | 图10和12,IVIDI≥2.0V VID≦15ns | 5 |
| Receiver enable to output low | TRZL | 20 | 50 | ns | 图5和11,CL=100pF S1关闭 | 5 | |
| Receiver enable to output high | TRZH | 20 | 50 | ns | 图5和11,CL=100pF S2关闭 | 5 | |
| Receiver low to disable time | TRLZ | 20 | 50 | ns | 图5和11,CL=100pF S1关闭 | 5 | |
| Receiver high to disable time | TRHZ | 20 | 50 | ns | 图5和11,CL=100pF S2关闭 | 5 | |
| Standby time | TSHDN | 50 | 200 | 600 | ns | 5 | |
| Driver enable from standby to output high | TDZH(SHDN) | 250 | ns | 图7和9,CL=15pF S2关闭 | 5 | ||
| Driver enable from standby to output low | TDZL(SHDN) | 250 | ns | 图7和9,CL=15pF S1关闭 | 5 | ||
| Receiver enable from standby to output high | TRZH(SHDN) | 3500 | ns | 图5和11,CL=100pF S2关闭 | 5 | ||
| Receiver enable from standby to output low | TRZL(SHDN) | 3500 | ns | 图5和11,CL=100pF S1关闭 | 5 | ||
| Supply voltage (absolute maximum) | VCC | 7 | V | 3 | |||
| Control input voltage /RE, DE | /RE, DE | -0.3 | V | 3 | |||
| Driver input voltage DI | DI | -0.3 | V | 3 | |||
| Driver output voltage A, B | A, B | -13 | 13 | V | 3 | ||
| Receiver input voltage A, B | A, B | -13 | 13 | V | 3 | ||
| Receiver output voltage RO | RO | -0.3 | V | 3 | |||
| Storage temperature | -65 | 150 | ℃ | 3 | |||
| Soldering temperature | TLEAD | 260 | ℃ | 10 S | 3 | ||
| Operating temperature range (SN75176) | 0 | 70 | ℃ | SN75176 | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | gold | 3 Lead frame Cu-Alloy 4 Wire Au or Cu | 9 |
CAD (KiCad official)
- Symbol:
SN75176N - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: DIP-8 (KiCad packages3D, STEP)
- 3D model files:
sn75176n-etched.step/sn75176n-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn75176n.step/sn75176n.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (13 pp, sha256
8e5fdac042fb5787, retrieved 2026-10-18, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).