Generated by kicad-footprint-generator · KiCad file format 20260206
SN74V245-7PAG
Texas Instruments · FIFOs Memory · TQFP-64(10x10)
SN74V245-7PAG from Texas Instruments, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D0 | input | Data input bit D0 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 2 | D1 | input | Data input bit D1 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 3 | D2 | input | Data input bit D2 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 4 | D3 | input | Data input bit D3 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 5 | D4 | input | Data input bit D4 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 6 | D5 | input | Data input bit D5 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 7 | D6 | input | Data input bit D6 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 8 | D7 | input | Data input bit D7 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 9 | D8 | input | Data input bit D8 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 10 | D9 | input | Data input bit D9 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 11 | D10 | input | Data input bit D10 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 12 | D11 | input | Data input bit D11 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 13 | D12 | input | Data input bit D12 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 14 | D13 | input | Data input bit D13 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 15 | D14 | input | Data input bit D14 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 16 | D15 | input | Data input bit D15 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 17 | PAE | output | Programmable almost-empty flag; goes low when the FIFO is almost empty based on the programmed offset (default 127 from empty for SN74V245). |
| 18 | FL | input | Mode selection input which, with WXI and RXI, selects standard or FWFT mode and synchronous or asynchronous PAE/PAF flags; grounded on the first device in daisy-chain depth expansion. |
| 19 | WCLK | input | Write clock; when WEN is low, data is written into the FIFO on a low-to-high transition of WCLK if the FIFO is not full. |
| 20 | WEN | input | Write enable; when low, data is written on every low-to-high transition of WCLK, and it is ignored when the FIFO is full. |
| 21 | WXI | input | Width-expansion input which, with FL and RXI, selects the FIFO mode and PAE/PAF flag synchronization; connected to WXO of the previous device in depth expansion. |
| 22 | VCC | power_in | +3.3-V power supply pin. |
| 23 | PAF | output | Programmable almost-full flag; goes low when the FIFO is almost full based on the programmed offset (default 127 from full for SN74V245). |
| 24 | RXI | input | Read-expansion input which, with FL and WXI, selects the FIFO mode and PAE/PAF flag synchronization; connected to RXO of the previous device in depth expansion. |
| 25 | FF/IR | output | Full flag in standard mode (low when FIFO is full) or input-ready flag in FWFT mode (indicates space available for writing). |
| 26 | WXO/HF | output | Half-full flag in single-device or width-expansion configuration (low when more than half full); write-expansion output pulse in depth expansion. |
| 27 | RXO | output | Last-location-read flag; in depth expansion a pulse is sent to RXI of the next device when the last FIFO location is read. |
| 28 | Q0 | output | Data output bit Q0 of the 18-bit read bus; high-impedance when OE is high. |
| 29 | Q1 | output | Data output bit Q1 of the 18-bit read bus; high-impedance when OE is high. |
| 30 | GND | power_in | Ground pin. |
| 31 | Q2 | output | Data output bit Q2 of the 18-bit read bus; high-impedance when OE is high. |
| 32 | Q3 | output | Data output bit Q3 of the 18-bit read bus; high-impedance when OE is high. |
| 33 | VCC | power_in | +3.3-V power supply pin. |
| 34 | Q4 | output | Data output bit Q4 of the 18-bit read bus; high-impedance when OE is high. |
| 35 | GND | power_in | Ground pin. |
| 36 | Q5 | output | Data output bit Q5 of the 18-bit read bus; high-impedance when OE is high. |
| 37 | Q6 | output | Data output bit Q6 of the 18-bit read bus; high-impedance when OE is high. |
| 38 | Q7 | output | Data output bit Q7 of the 18-bit read bus; high-impedance when OE is high. |
| 39 | Q8 | output | Data output bit Q8 of the 18-bit read bus; high-impedance when OE is high. |
| 40 | GND | power_in | Ground pin. |
| 41 | Q9 | output | Data output bit Q9 of the 18-bit read bus; high-impedance when OE is high. |
| 42 | Q10 | output | Data output bit Q10 of the 18-bit read bus; high-impedance when OE is high. |
| 43 | VCC | power_in | +3.3-V power supply pin. |
| 44 | Q11 | output | Data output bit Q11 of the 18-bit read bus; high-impedance when OE is high. |
| 45 | Q12 | output | Data output bit Q12 of the 18-bit read bus; high-impedance when OE is high. |
| 46 | GND | power_in | Ground pin. |
| 47 | Q13 | output | Data output bit Q13 of the 18-bit read bus; high-impedance when OE is high. |
| 48 | Q14 | output | Data output bit Q14 of the 18-bit read bus; high-impedance when OE is high. |
| 49 | VCC | power_in | +3.3-V power supply pin. |
| 50 | Q15 | output | Data output bit Q15 of the 18-bit read bus; high-impedance when OE is high. |
| 51 | GND | power_in | Ground pin. |
| 52 | Q16 | output | Data output bit Q16 of the 18-bit read bus; high-impedance when OE is high. |
| 53 | Q17 | output | Data output bit Q17 of the 18-bit read bus; high-impedance when OE is high. |
| 54 | EF/OR | output | Empty flag in standard mode (low when FIFO is empty) or output-ready flag in FWFT mode (indicates valid data at outputs). |
| 55 | GND | power_in | Ground pin. |
| 56 | VCC | power_in | +3.3-V power supply pin. |
| 57 | RS | input | Reset input; when low, read and write pointers are reset, FF and PAF go high, and PAE and EF go low, and a reset is required after power-up before the first write. |
| 58 | OE | input | Output enable; when low the Q data output bus is active, and when high it is in the high-impedance state. |
| 59 | LD | input | Load control; when low with WEN low, data on D0-D11 is written to the offset registers on the low-to-high transition of WCLK. |
| 60 | REN | input | Read enable; when low, data is read from the FIFO on every low-to-high transition of RCLK, and it is ignored when the FIFO is empty. |
| 61 | RCLK | input | Read clock; when REN is low, data is read from the FIFO on a low-to-high transition of RCLK if the FIFO is not empty. |
| 62 | GND | power_in | Ground pin. |
| 63 | D16 | input | Data input bit D16 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
| 64 | D17 | input | Data input bit D17 of the 18-bit write bus, loaded on the low-to-high transition of WCLK when WEN is low. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-64(10x10) |
| Category | Logic |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 3 | 3.3 | 3.6 | V | 37 | |
| Supply voltage | GND | 0 | 0 | 0 | V | 37 | |
| High-level input voltage | VIH | 2 | 5 | V | 37 | ||
| Low-level input voltage | VIL | 0.8 | V | 37 | |||
| Operating free-air temperature | TA | 0 | 70 | °C | 37 | ||
| Supply voltage range | VCC | -0.5 | 5 | V | over operating free-air temperature range | 37 | |
| Continuous output current | IO | -50 | 50 | mA | VO = 0 to VCC | 37 | |
| Storage temperature range | Tstg | -55 | 125 | °C | 37 | ||
| High-level output voltage | VOH | 2.4 | V | VCC = 3.0 V, IOH = -2 mA | 37 | ||
| Low-level output voltage | VOL | 0.4 | V | VCC = 3.0 V, IOL = 8 mA | 37 | ||
| Input current | II | -1 | 1 | µA | VCC = 3.6 V, VI = VCC to 0.4 V | 37 | |
| Off-state output current | IOZ | -10 | 10 | µA | VCC = 3.6 V, OE ≥ VIH, VO = VCC to 0.4 V | 37 | |
| Supply current | ICC1 | 35 | mA | VCC = 3.3 V, See Notes 1, 2, and 3 | 37 | ||
| Supply current | ICC2 | 5 | mA | VCC = 3.6 V, See Notes 1 and 4 | 37 | ||
| Input capacitance | CIN | 10 | pF | VI = 0, TA = 25°C, f = 1 MHz | 37 | ||
| Output capacitance | COUT | 10 | pF | VO = 0, TA = 25°C, f = 1 MHz, Output deselected, (OE ≥ VIH) | 37 | ||
| Clock cycle frequency | fclock | 133 | MHz | '74V245-7 | 38 | ||
| Data access time | tA | 2 | 5 | ns | '74V245-7 | 38 | |
| Clock cycle time | tCLK | 7.5 | ns | '74V245-7 | 38 | ||
| Clock high time | tCLKH | 3.5 | ns | '74V245-7 | 38 | ||
| Clock low time | tCLKL | 3.5 | ns | '74V245-7 | 38 | ||
| Data setup time | tDS | 2.5 | ns | '74V245-7 | 38 | ||
| Data hold time | tDH | 0.5 | ns | '74V245-7 | 38 | ||
| Enable setup time | tENS | 2.5 | ns | '74V245-7 | 38 | ||
| Enable hold time | tENH | 0.5 | ns | '74V245-7 | 38 | ||
| Load setup time | tLDS | 3.5 | ns | '74V245-7 | 38 | ||
| Load hold time | tLDH | 0.5 | ns | '74V245-7 | 38 | ||
| Reset pulse width | tRS | 10 | ns | '74V245-7 | 38 | ||
| Reset setup time | tRSS | 8 | ns | '74V245-7 | 38 | ||
| Reset recovery time | tRSR | 8 | ns | '74V245-7 | 38 | ||
| Reset to flag and output time | tRSF | 15 | ns | '74V245-7 | 38 | ||
| Output enable to output in low Z | tOLZ | 0 | ns | '74V245-7 | 38 | ||
| Output enable to output valid | tOE | 6 | ns | '74V245-7 | 38 | ||
| Output enable to output in high Z | tOHZ | 1 | 6 | ns | '74V245-7 | 38 | |
| Write clock to Full flag | tWFF | 5 | ns | '74V245-7 | 38 | ||
| Read clock to Empty flag | tREF | 5 | ns | '74V245-7 | 38 | ||
| Clock to asynchronous programmable Almost-Full flag | tPAFA | 12.5 | ns | '74V245-7 | 38 | ||
| Write clock to synchronous programmable Almost-Full flag | tPAFS | 5 | ns | '74V245-7 | 38 | ||
| Clock to asynchronous programmable Almost-Empty flag | tPAEA | 12.5 | ns | '74V245-7 | 38 | ||
| Read clock to synchronous programmable Almost-Empty flag | tPAES | 5 | ns | '74V245-7 | 38 | ||
| Clock to Half-Full flag | tHF | 12.5 | ns | '74V245-7 | 38 | ||
| Clock to expansion out | tXO | 5 | ns | '74V245-7 | 38 | ||
| Expansion in pulse duration | tXI | 2.5 | ns | '74V245-7 | 38 | ||
| Expansion in setup time | tXIS | 2.5 | ns | '74V245-7 | 38 | ||
| Skew time between read clock and write clock for FF/IR and EF/OR | tSKEW1 | 5 | ns | '74V245-7 | 38 | ||
| Skew time between read clock and write clock for PAE and PAF (synchronous only) | tSKEW2 | 7 | ns | '74V245-7 | 38 |
CAD (KiCad official)
- Symbol:
SN74V245-7PAG - Footprint:
Package_QFP:TQFP-64_10x10mm_P0.5mm - 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
sn74v245-7pag-etched.step/sn74v245-7pag-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn74v245-7pag.step/sn74v245-7pag.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (48 pp, sha256
0854662bbf248bdd, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).