3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSN74ALVTH16374DLR
Texas Instruments · Flip Flops · SSOP-48-300mil
SN74ALVTH16374DLR from Texas Instruments, in a SSOP-48-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | 1OE | input | Active-low output enable for outputs 1Q1 to 1Q8; when high, the outputs go to high impedance, and OE should be tied to VCC through a pullup resistor to keep the high-impedance state above 1.2 V. |
| 2 | 1Q1 | tri_state | Three-state output of channel 1 flip-flop 1D1, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 3 | 1Q2 | tri_state | Three-state output of channel 1 flip-flop 1D2, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | 1Q3 | tri_state | Three-state output of channel 1 flip-flop 1D3, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 6 | 1Q4 | tri_state | Three-state output of channel 1 flip-flop 1D4, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 7 | VCC | power_in | Supply voltage: 2.3 V to 2.7 V for 2.5 V operation or 3 V to 3.6 V for 3.3 V operation. |
| 8 | 1Q5 | tri_state | Three-state output of channel 1 flip-flop 1D5, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 9 | 1Q6 | tri_state | Three-state output of channel 1 flip-flop 1D6, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 10 | GND | power_in | Ground reference for the device. |
| 11 | 1Q7 | tri_state | Three-state output of channel 1 flip-flop 1D7, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 12 | 1Q8 | tri_state | Three-state output of channel 1 flip-flop 1D8, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 13 | 2Q1 | tri_state | Three-state output of channel 2 flip-flop 2D1, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 14 | 2Q2 | tri_state | Three-state output of channel 2 flip-flop 2D2, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 15 | GND | power_in | Ground reference for the device. |
| 16 | 2Q3 | tri_state | Three-state output of channel 2 flip-flop 2D3, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 17 | 2Q4 | tri_state | Three-state output of channel 2 flip-flop 2D4, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 18 | VCC | power_in | Supply voltage: 2.3 V to 2.7 V for 2.5 V operation or 3 V to 3.6 V for 3.3 V operation. |
| 19 | 2Q5 | tri_state | Three-state output of channel 2 flip-flop 2D5, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 20 | 2Q6 | tri_state | Three-state output of channel 2 flip-flop 2D6, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 21 | GND | power_in | Ground reference for the device. |
| 22 | 2Q7 | tri_state | Three-state output of channel 2 flip-flop 2D7, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 23 | 2Q8 | tri_state | Three-state output of channel 2 flip-flop 2D8, with high drive of -32 mA high-level and 32 mA low-level at 3.3 V VCC. |
| 24 | 2OE | input | Active-low output enable for outputs 2Q1 to 2Q8; when high, the outputs go to high impedance, and OE should be tied to VCC through a pullup resistor to keep the high-impedance state above 1.2 V. |
| 25 | 2CLK | input | Clock input for the channel 2 flip-flops; data is stored on the positive (rising) CLK transition, with minimum pulse width of 1.5 ns. |
| 26 | 2D8 | input | Data input to channel 2 flip-flop 8; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 27 | 2D7 | input | Data input to channel 2 flip-flop 7; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 28 | GND | power_in | Ground reference for the device. |
| 29 | 2D6 | input | Data input to channel 2 flip-flop 6; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 30 | 2D5 | input | Data input to channel 2 flip-flop 5; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 31 | VCC | power_in | Supply voltage: 2.3 V to 2.7 V for 2.5 V operation or 3 V to 3.6 V for 3.3 V operation. |
| 32 | 2D4 | input | Data input to channel 2 flip-flop 4; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 33 | 2D3 | input | Data input to channel 2 flip-flop 3; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 34 | GND | power_in | Ground reference for the device. |
| 35 | 2D2 | input | Data input to channel 2 flip-flop 2; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 36 | 2D1 | input | Data input to channel 2 flip-flop 1; the value is stored on the rising edge of 2CLK, and bus hold holds the input at a valid level when floating. |
| 37 | 1D8 | input | Data input to channel 1 flip-flop 8; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 38 | 1D7 | input | Data input to channel 1 flip-flop 7; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 39 | GND | power_in | Ground reference for the device. |
| 40 | 1D6 | input | Data input to channel 1 flip-flop 6; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 41 | 1D5 | input | Data input to channel 1 flip-flop 5; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 42 | VCC | power_in | Supply voltage: 2.3 V to 2.7 V for 2.5 V operation or 3 V to 3.6 V for 3.3 V operation. |
| 43 | 1D4 | input | Data input to channel 1 flip-flop 4; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 44 | 1D3 | input | Data input to channel 1 flip-flop 3; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 45 | GND | power_in | Ground reference for the device. |
| 46 | 1D2 | input | Data input to channel 1 flip-flop 2; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 47 | 1D1 | input | Data input to channel 1 flip-flop 1; the value is stored on the rising edge of 1CLK, and bus hold holds the input at a valid level when floating. |
| 48 | 1CLK | input | Clock input for the channel 1 flip-flops; data is stored on the positive (rising) CLK transition, with minimum pulse width of 1.5 ns. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SSOP-48-300mil |
| Category | Logic ICs |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 2.3 | 2.7 | V | VCC = 2.5 V ± 0.2 V | 5 | |
| High-level input voltage | VIH | 1.7 | V | VCC = 2.5 V ± 0.2 V | 5 | ||
| Low-level input voltage | VIL | 0.7 | V | VCC = 2.5 V ± 0.2 V | 5 | ||
| Input voltage | VI | 0 | 5.5 | V | VCC = 2.5 V ± 0.2 V | 5 | |
| High-level output current | IOH | -8 | mA | VCC = 2.5 V ± 0.2 V | 5 | ||
| Low-level output current | IOL | 8 | mA | VCC = 2.5 V ± 0.2 V | 5 | ||
| Low-level output current, duty cycle limited | IOL | 24 | mA | current duty cycle ≤ 50%; f ≥ 1 kHz | 5 | ||
| Input transition rise or fall rate | ∆t/∆v | 10 | ns/V | Outputs enabled | 5 | ||
| Power-up ramp rate | ∆t/∆VCC | 200 | µs/V | VCC = 2.5 V ± 0.2 V | 5 | ||
| Operating free-air temperature | TA | -40 | 85 | °C | SN74ALVTH16374 | 5 | |
| Supply voltage | VCC | 3 | 3.6 | V | VCC = 3.3 V ± 0.3 V | 5 | |
| High-level input voltage | VIH | 2 | V | VCC = 3.3 V ± 0.3 V | 5 | ||
| Low-level input voltage | VIL | 0.8 | V | VCC = 3.3 V ± 0.3 V | 5 | ||
| High-level output current | IOH | -32 | mA | VCC = 3.3 V ± 0.3 V | 5 | ||
| Low-level output current | IOL | 32 | mA | VCC = 3.3 V ± 0.3 V | 5 | ||
| Low-level output current, duty cycle limited | IOL | 64 | mA | current duty cycle ≤ 50%; f ≥ 1 kHz | 5 | ||
| Supply voltage range | VCC | -0.5 | 4.6 | V | 4 | ||
| Input voltage range | VI | -0.5 | 7 | V | 4 | ||
| Voltage range applied to any output in the high-impedance or power-off state | VO | -0.5 | 7 | V | 4 | ||
| Voltage range applied to any output in the high state | VO | -0.5 | 7 | V | 4 | ||
| Output current in the low state | IO | 128 | mA | SN74ALVTH16374 | 4 | ||
| Output current in the high state | IO | -64 | mA | SN74ALVTH16374 | 4 | ||
| Input clamp current | IIK | -50 | mA | VI < 0 | 4 | ||
| Output clamp current | IOK | -50 | mA | VO < 0 | 4 | ||
| Package thermal impedance, DL package | θJA | 94 | °C/W | DL package; calculated per JESD 51 | 4 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 4 | ||
| High-level output voltage | VOH | 1.8 | V | VCC = 2.3 V, IOH = -8 mA | 6 | ||
| Input clamp voltage | VIK | -1.2 | V | VCC = 2.3 V, II = -18 mA | 6 | ||
| Low-level output voltage | VOL | 0.2 | V | VCC = 2.3 V to 2.7 V, IOL = 100 µA | 6 | ||
| Low-level output voltage | VOL | 0.4 | V | VCC = 2.3 V, IOL = 8 mA | 6 | ||
| Low-level output voltage | VOL | 0.5 | V | VCC = 2.3 V, IOL = 24 mA | 6 | ||
| Control inputs input current | II | -1 | 1 | µA | VCC = 2.7 V, VI = VCC or GND | 6 | |
| Bus-hold low sustaining current | IBHL | 115 | µA | VCC = 2.3 V, VI = 0.7 V | 6 | ||
| Bus-hold high sustaining current | IBHH | -10 | µA | VCC = 2.3 V, VI = 1.7 V | 6 | ||
| Supply current, outputs high | ICC | 0.1 | mA | VCC = 2.7 V, IO = 0, VI = VCC or GND | 6 | ||
| Supply current, outputs low | ICC | 4.5 | mA | VCC = 2.7 V, IO = 0, VI = VCC or GND | 6 | ||
| High-level output voltage | VOH | 2 | V | VCC = 3 V, IOH = -32 mA | 7 | ||
| Input clamp voltage | VIK | -1.2 | V | VCC = 3 V, II = -18 mA | 7 | ||
| Low-level output voltage | VOL | 0.2 | V | VCC = 3 V to 3.6 V, IOL = 100 µA | 7 | ||
| Low-level output voltage | VOL | 0.4 | V | IOL = 16 mA | 7 | ||
| Low-level output voltage | VOL | 0.5 | V | VCC = 3 V, IOL = 32 mA | 7 | ||
| Low-level output voltage | VOL | 0.55 | V | IOL = 64 mA | 7 | ||
| Control inputs input current | II | -1 | 1 | µA | VCC = 3.6 V, VI = VCC or GND | 7 | |
| Bus-hold low sustaining current | IBHL | 75 | µA | VCC = 3 V, VI = 0.8 V | 7 | ||
| Supply current, outputs low | ICC | 3.2 | 5 | mA | VCC = 3.6 V, IO = 0, VI = VCC or GND | 7 | |
| Supply current increase per TTL input | ∆ICC | 0.4 | mA | VCC = 3 V to 3.6 V, one input at VCC, 0.6 V, other inputs at VCC or GND | 7 | ||
| Maximum clock frequency | fmax | 150 | MHz | CL = 30 pF, VCC = 2.5 V ± 0.2 V | 9 | ||
| Propagation delay CLK to Q | tPLH | 1.5 | 3.8 | ns | CL = 30 pF, VCC = 2.5 V ± 0.2 V | 9 | |
| Enable time OE to Q | tPZH | 1 | 4.1 | ns | CL = 30 pF, VCC = 2.5 V ± 0.2 V | 9 | |
| Disable time OE to Q | tPHZ | 1.8 | 4.2 | ns | CL = 30 pF, VCC = 2.5 V ± 0.2 V | 9 | |
| Maximum clock frequency | fmax | 250 | MHz | CL = 50 pF, VCC = 3.3 V ± 0.3 V | 9 | ||
| Propagation delay CLK to Q | tPLH | 1 | 3.2 | ns | CL = 50 pF, VCC = 3.3 V ± 0.3 V | 9 | |
| Enable time OE to Q | tPZH | 1 | 3.8 | ns | CL = 50 pF, VCC = 3.3 V ± 0.3 V | 9 | |
| Disable time OE to Q | tPHZ | 1 | 4.6 | ns | CL = 50 pF, VCC = 3.3 V ± 0.3 V | 9 |
CAD (KiCad official)
- Symbol:
SN74ALVTH16374DLR - Footprint:
Package_SO:SSOP-48_7.5x15.9mm_P0.635mm - 3D model: SSOP-48-300mil (KiCad packages3D, STEP)
- 3D model files:
sn74alvth16374dlr-etched.step/sn74alvth16374dlr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn74alvth16374dlr.step/sn74alvth16374dlr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (19 pp, sha256
e2900bdbb666b19c, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).