main
History Download
Ray Publish 0.1.0 74a97a1

SN65LBC184N

lingxingic · RS-485 / RS-422 ICs · DIP-8

SN65LBC184N from lingxingic, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 R output Receiver output; with /RE low it outputs a logic level from the differential input, and it goes high-impedance when /RE is high, with VOH of at least 3 V at IOH = -8 mA and VOL of at most 0.4 V at IOL = 8 mA.
2 /RE input Active-low receiver enable; driving it high puts the receiver output R into high-impedance, and the logic input high level is at least 2 V and low level at most 0.8 V.
3 DE input Driver enable; when low the driver outputs A and B are high-impedance, and when high the driver is enabled, with logic input high level at least 2 V and low level at most 0.8 V.
4 D input Driver input; the logic level on D sets the differential output on A and B when DE is high, with logic input high level at least 2 V and low level at most 0.8 V.
5 GND power_in Ground reference for the device.
6 A bidirectional Non-inverting receiver input and non-inverting driver output on the bus; bus pins are rated ±15 kV HBM ESD, with a common-mode range of -7 V to 12 V.
7 B bidirectional Inverting receiver input and inverting driver output on the bus; bus pins are rated ±15 kV HBM ESD, with a common-mode range of -7 V to 12 V.
8 VCC power_in Supply pin; the operating supply range is 3 V to 5.5 V (absolute maximum 7 V).

Key specifications

Parameter Value
Manufacturer lingxingic
Package DIP-8
Category Interface
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
电源电压 VCC -0.3 7 V 5
输入电压 VI -0.3 V D, DE, /RE 5
输入/输出电压 VI/O -15 15 V A,B 5
输入/输出电压 VI/O -0.3 V R 5
电源电压 VCC 3 5.5 V 5
共模电压 VCM -7 12 V 5
高电平输入电压 VIH 2 V 驱动器输入、使能与接收器使能 5
低电平输入电压 VIL 0 0.8 V 5
差分输入电压 VID -7 12 V 5
差分负载电阻 RL 54 Ω printed as >54 5
工作温度 Tamb -40 85 ℃ 5
贮存温度 Tstg -65 150 ℃ 5
ESD HBM 总线引脚(A,B) -15 15 kV HBM 5
ESD HBM 所有其他引脚 -15 15 kV HBM 5
工作电压 VCC 3 5.5 V 6
静态电流 ICC 650 750 uA DE=VCC,/RE=GND,无负载 6
静态电流 ICC 450 600 uA DE=VCC,/RE=VCC,无负载 6
静态电流 ICC 400 600 uA DE=GND,/RE=GND,无负载 6
静态电流 ICC 1 uA DE=GND,/RE=VCC,无负载 6
差分输出电压幅度 /VOD/ 2.1 3.5 V RL=60Ω@VA&VB(-7~12V) VCC=4.5~5.5V 图1A 6
差分输出电压幅度 /VOD/ 1.5 2.2 V RL=60Ω@VA&VB(-7~12V) VCC=3.0~3.6V 6
差分输出电压幅度 /VOD/ 2 3.4 V RL=54Ω,VCC=5V 图1B 6
差分输出电压幅度 /VOD/ 1.5 1.9 V RL=54Ω,VCC=3V 6
差分输出电压幅度 /VOD/ 2.7 4 V RL=100Ω,VCC=5V 6
差分输出电压幅度 /VOD/ 2 2.3 V RL=100Ω,VCC=3V 6
差分输出电压幅度差值 ∆/VOD/ -50 2 50 mV RL=54Ω,VCC=5V,CL=50pF 6
稳态共模输出电压 VOC(SS) 1 3 V 两个 27Ω 负载电阻的中心 6
短路输出电流 /IOS/ -250 110 250 mA VA/VB:-7~12V 6
总线引脚 A,B 短路电流 150 mA 6
正向差分输入电压阈值 VIT+ -110 -40 mV VA/VB:-7~12V 6
负向差分输入电压阈值 VIT- -220 -140 mV VA/VB:-7~12V 6
输出高电平电压 VOH 3 4.6 V IOH=-8mA 6
输出低电平电压 VOL 0.4 V IOL=8mA 6
高阻输出电流 IOZ -1 1 uA VO=0/VCC,/RE=VCC 6
总线输入电流(驱动器关闭) IIN 120 uA VCC=4.5~5.5 或 VCC=0, DE 为 0V; VI=12V 6
总线输入电流(驱动器关闭) IIN -110 uA VCC=4.5~5.5 或 VCC=0, DE 为 0V; VI=-7V 6
总线输入阻抗 RA/RB 96 KΩ VA=-7V,VB=12V 和 VA=12V,VB=-7V 6
逻辑输入高电压 VIH 2 V DI,DE,/RE 6
逻辑输入低电压 VIL 0.8 V 6
输入漏电 Ii -5 5 uA 6
最大数据速率 fMAX 500 Kbps VOD≥±1.5V,RL=54Ω,CL=100pF(图2) 7
关闭时间(驱动器) tPHZ 35 90 ns CL=15pF,SW2 闭合 图4 7
关闭时间(驱动器) tPLZ 50 90 ns CL=15pF,SW1 闭合 7
启动时间(驱动器) tPZH 160 450 ns CL=100pF,RX 使能,SW2 闭合 7
启动时间(驱动器) tPZH 2600 3200 ns CL=100pF,RX 禁用,SW2 闭合 7
启动时间(驱动器) tPZL 140 450 ns CL=100pF,RX 使能,SW1 闭合 7
驱动器传输延迟偏差 /tPHL- tPLH/ 20 ns 7
传播延迟时间(接收器) tPHL,tPLH 80 150 ns 7
接收器传输延迟偏差 /tPHL-tPLH/ 25 ns 7
关闭时间(接收器) tPHZ 20 65 ns SW2 闭合 图6 7
启动时间(接收器) tPZH 110 200 ns TX 使能,SW2 闭合 7
启动时间(接收器) tPZH 2700 3200 ns TX 禁用,SW2 闭合 7
启动时间(接收器) tPZL 27 50 ns TX 使能,SW1 闭合 7
启动时间(接收器) tPZL 2400 3200 ns TX 禁用,SW1 闭合 7

CAD (KiCad official)

  • Symbol: SN65LBC184N
  • Footprint: Package_DIP:DIP-8_W7.62mm
  • 3D model: DIP-8 (KiCad packages3D, STEP)
  • 3D model files: sn65lbc184n-etched.step / sn65lbc184n-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sn65lbc184n.step / sn65lbc184n.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: lingxingic datasheet (12 pp, sha256 c875dd05b5d076d4, retrieved 2026-10-14, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF