Generated by kicad-footprint-generator · KiCad file format 20260206
SN65LBC184N
lingxingic · RS-485 / RS-422 ICs · DIP-8
SN65LBC184N from lingxingic, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | R | output | Receiver output; with /RE low it outputs a logic level from the differential input, and it goes high-impedance when /RE is high, with VOH of at least 3 V at IOH = -8 mA and VOL of at most 0.4 V at IOL = 8 mA. |
| 2 | /RE | input | Active-low receiver enable; driving it high puts the receiver output R into high-impedance, and the logic input high level is at least 2 V and low level at most 0.8 V. |
| 3 | DE | input | Driver enable; when low the driver outputs A and B are high-impedance, and when high the driver is enabled, with logic input high level at least 2 V and low level at most 0.8 V. |
| 4 | D | input | Driver input; the logic level on D sets the differential output on A and B when DE is high, with logic input high level at least 2 V and low level at most 0.8 V. |
| 5 | GND | power_in | Ground reference for the device. |
| 6 | A | bidirectional | Non-inverting receiver input and non-inverting driver output on the bus; bus pins are rated ±15 kV HBM ESD, with a common-mode range of -7 V to 12 V. |
| 7 | B | bidirectional | Inverting receiver input and inverting driver output on the bus; bus pins are rated ±15 kV HBM ESD, with a common-mode range of -7 V to 12 V. |
| 8 | VCC | power_in | Supply pin; the operating supply range is 3 V to 5.5 V (absolute maximum 7 V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | lingxingic |
| Package | DIP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 | VCC | -0.3 | 7 | V | 5 | ||
| 输入电压 | VI | -0.3 | V | D, DE, /RE | 5 | ||
| 输入/输出电压 | VI/O | -15 | 15 | V | A,B | 5 | |
| 输入/输出电压 | VI/O | -0.3 | V | R | 5 | ||
| 电源电压 | VCC | 3 | 5.5 | V | 5 | ||
| 共模电压 | VCM | -7 | 12 | V | 5 | ||
| 高电平输入电压 | VIH | 2 | V | 驱动器输入、使能与接收器使能 | 5 | ||
| 低电平输入电压 | VIL | 0 | 0.8 | V | 5 | ||
| 差分输入电压 | VID | -7 | 12 | V | 5 | ||
| 差分负载电阻 | RL | 54 | Ω | printed as >54 | 5 | ||
| 工作温度 | Tamb | -40 | 85 | ℃ | 5 | ||
| 贮存温度 | Tstg | -65 | 150 | ℃ | 5 | ||
| ESD HBM 总线引脚(A,B) | -15 | 15 | kV | HBM | 5 | ||
| ESD HBM 所有其他引脚 | -15 | 15 | kV | HBM | 5 | ||
| 工作电压 | VCC | 3 | 5.5 | V | 6 | ||
| 静态电流 | ICC | 650 | 750 | uA | DE=VCC,/RE=GND,无负载 | 6 | |
| 静态电流 | ICC | 450 | 600 | uA | DE=VCC,/RE=VCC,无负载 | 6 | |
| 静态电流 | ICC | 400 | 600 | uA | DE=GND,/RE=GND,无负载 | 6 | |
| 静态电流 | ICC | 1 | uA | DE=GND,/RE=VCC,无负载 | 6 | ||
| 差分输出电压幅度 | /VOD/ | 2.1 | 3.5 | V | RL=60Ω@VA&VB(-7~12V) VCC=4.5~5.5V 图1A | 6 | |
| 差分输出电压幅度 | /VOD/ | 1.5 | 2.2 | V | RL=60Ω@VA&VB(-7~12V) VCC=3.0~3.6V | 6 | |
| 差分输出电压幅度 | /VOD/ | 2 | 3.4 | V | RL=54Ω,VCC=5V 图1B | 6 | |
| 差分输出电压幅度 | /VOD/ | 1.5 | 1.9 | V | RL=54Ω,VCC=3V | 6 | |
| 差分输出电压幅度 | /VOD/ | 2.7 | 4 | V | RL=100Ω,VCC=5V | 6 | |
| 差分输出电压幅度 | /VOD/ | 2 | 2.3 | V | RL=100Ω,VCC=3V | 6 | |
| 差分输出电压幅度差值 | ∆/VOD/ | -50 | 2 | 50 | mV | RL=54Ω,VCC=5V,CL=50pF | 6 |
| 稳态共模输出电压 | VOC(SS) | 1 | 3 | V | 两个 27Ω 负载电阻的中心 | 6 | |
| 短路输出电流 | /IOS/ | -250 | 110 | 250 | mA | VA/VB:-7~12V | 6 |
| 总线引脚 A,B 短路电流 | 150 | mA | 6 | ||||
| 正向差分输入电压阈值 | VIT+ | -110 | -40 | mV | VA/VB:-7~12V | 6 | |
| 负向差分输入电压阈值 | VIT- | -220 | -140 | mV | VA/VB:-7~12V | 6 | |
| 输出高电平电压 | VOH | 3 | 4.6 | V | IOH=-8mA | 6 | |
| 输出低电平电压 | VOL | 0.4 | V | IOL=8mA | 6 | ||
| 高阻输出电流 | IOZ | -1 | 1 | uA | VO=0/VCC,/RE=VCC | 6 | |
| 总线输入电流(驱动器关闭) | IIN | 120 | uA | VCC=4.5~5.5 或 VCC=0, DE 为 0V; VI=12V | 6 | ||
| 总线输入电流(驱动器关闭) | IIN | -110 | uA | VCC=4.5~5.5 或 VCC=0, DE 为 0V; VI=-7V | 6 | ||
| 总线输入阻抗 | RA/RB | 96 | KΩ | VA=-7V,VB=12V 和 VA=12V,VB=-7V | 6 | ||
| 逻辑输入高电压 | VIH | 2 | V | DI,DE,/RE | 6 | ||
| 逻辑输入低电压 | VIL | 0.8 | V | 6 | |||
| 输入漏电 | Ii | -5 | 5 | uA | 6 | ||
| 最大数据速率 | fMAX | 500 | Kbps | VOD≥±1.5V,RL=54Ω,CL=100pF(图2) | 7 | ||
| 关闭时间(驱动器) | tPHZ | 35 | 90 | ns | CL=15pF,SW2 闭合 图4 | 7 | |
| 关闭时间(驱动器) | tPLZ | 50 | 90 | ns | CL=15pF,SW1 闭合 | 7 | |
| 启动时间(驱动器) | tPZH | 160 | 450 | ns | CL=100pF,RX 使能,SW2 闭合 | 7 | |
| 启动时间(驱动器) | tPZH | 2600 | 3200 | ns | CL=100pF,RX 禁用,SW2 闭合 | 7 | |
| 启动时间(驱动器) | tPZL | 140 | 450 | ns | CL=100pF,RX 使能,SW1 闭合 | 7 | |
| 驱动器传输延迟偏差 | /tPHL- tPLH/ | 20 | ns | 7 | |||
| 传播延迟时间(接收器) | tPHL,tPLH | 80 | 150 | ns | 7 | ||
| 接收器传输延迟偏差 | /tPHL-tPLH/ | 25 | ns | 7 | |||
| 关闭时间(接收器) | tPHZ | 20 | 65 | ns | SW2 闭合 图6 | 7 | |
| 启动时间(接收器) | tPZH | 110 | 200 | ns | TX 使能,SW2 闭合 | 7 | |
| 启动时间(接收器) | tPZH | 2700 | 3200 | ns | TX 禁用,SW2 闭合 | 7 | |
| 启动时间(接收器) | tPZL | 27 | 50 | ns | TX 使能,SW1 闭合 | 7 | |
| 启动时间(接收器) | tPZL | 2400 | 3200 | ns | TX 禁用,SW1 闭合 | 7 |
CAD (KiCad official)
- Symbol:
SN65LBC184N - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: DIP-8 (KiCad packages3D, STEP)
- 3D model files:
sn65lbc184n-etched.step/sn65lbc184n-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn65lbc184n.step/sn65lbc184n.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: lingxingic datasheet (12 pp, sha256
c875dd05b5d076d4, retrieved 2026-10-14, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).