Generated by kicad-footprint-generator · KiCad file format 20260206
SN65HVD78EIMM
HGSEMI · RS-485 / RS-422 ICs · MSOP-8
SN65HVD78EIMM from HGSEMI, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: with RE low, RO goes high when A-B is at least 200mV and low when A-B is at most -200mV as printed; the failsafe section and function table give the thresholds as -50mV (high) and -200mV (low). |
| 2 | RE | input | Receiver output enable, active low: RO is enabled when RE is low and is high-impedance when RE is high; RE high together with DE low puts the device into low-power shutdown mode. |
| 3 | DE | input | Driver output enable: the driver outputs are active when DE is high and high-impedance when DE is low; DE has a hot-plug input structure. |
| 4 | DI | input | Driver input: while DE is high, a low on DI drives A low and B high, and a high on DI drives A high and B low. |
| 5 | GND | power_in | Ground. |
| 6 | A | bidirectional | Receiver non-inverting input and driver non-inverting output. |
| 7 | B | bidirectional | Receiver inverting input and driver inverting output. |
| 8 | VCC | power_in | Positive supply: 3.15V ≤ VCC ≤ 3.45V; connect a 0.1µF capacitor to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | MSOP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 3.15 | 3.45 | V | 4 | ||
| Differential driver output voltage (RS-422 load) | VOD | 2 | V | 图1,RL=100Ω(RS-422) | 4 | ||
| Differential driver output voltage (RS-485 load) | VOD | 1.5 | V | 图1,RL=54Ω(RS-485) | 4 | ||
| Differential driver output voltage magnitude change | ΔVOD | 0.2 | V | 图1,RL=100Ω 或 RL=54Ω | 4 | ||
| Driver common-mode output voltage | VOC | 3 | V | 图1,RL=100Ω 或 RL=54Ω | 4 | ||
| Common-mode output voltage magnitude change | ΔVOC | 0.2 | V | 图1,RL=100Ω 或 RL=54Ω | 4 | ||
| Driver input high voltage | VIH | 2 | V | DE, DI | 5 | ||
| Driver input low voltage | VIL | 0.8 | V | DE, DI | 5 | ||
| Driver input current | IIN | -1 | 1 | μA | DE, DI | 5 | |
| Input current (A, B) full duplex, high side | IA, IB | 125 | μA | DE=GND, VCC=GND 或VCC, VIN=12V | 5 | ||
| Input current (A, B) full duplex, low side | IA, IB | -75 | μA | DE=GND, VCC=GND 或VCC, VIN=-7V | 5 | ||
| Output leakage current (Y, Z) full duplex, high side | IO | 125 | μA | DE=GND, VCC=GND 或VCC, VIN=12V | 5 | ||
| Output leakage current (Y, Z) full duplex, low side | IO | -100 | μA | DE=GND, VCC=GND 或VCC, VIN=-7V | 5 | ||
| Driver short-circuit output current | IOSD | 250 | mA | 0≦VOUT ≦12V | 5 | ||
| Driver short-circuit output current | IOSD | -250 | mA | -7≦VOUT ≦Vcc | 5 | ||
| Driver short-circuit foldback output current | IOSDF | 20 | mA | Vcc-1V ≦VOUT ≦Vcc+0.5V | 5 | ||
| Driver short-circuit foldback output current | IOSDF | -20 | mA | -0.5V ≦VOUT ≦+1V | 5 | ||
| Thermal shutdown temperature | TTS | 165 | ℃ | 5 | |||
| Receiver differential threshold voltage | VTH | -200 | -125 | -50 | mV | -7V≦VCM≦12V | 5 |
| Receiver output low voltage | VOL | 0.4 | V | IO= 4mA,VID=-200mV | 5 | ||
| Receiver tri-state output current | IOZR | -1 | 1 | μA | 0≦VO≦VCC | 5 | |
| Supply current (no load, DE=VCC) | Icc | 400 | 900 | μA | 无负载,(符号不可读)=VCC,DI=GND 或VCC,DE=VCC | 6 | |
| Supply current (no load, DE=GND) | Icc | 330 | 600 | μA | 无负载,(符号不可读)=VCC,DI=GND 或VCC,DE=GND | 6 | |
| Supply current (no load, DE=VCC, second condition) | Icc | 400 | 1000 | μA | 无负载,(符号不可读)=GND,DI=GND 或VCC,DE=VCC | 6 | |
| Supply current (no load, DE=GND, second condition) | Icc | 330 | 800 | μA | 无负载,(符号不可读)=GND,DI=GND 或VCC,DE=GND | 6 | |
| Standby supply current | ISHDN | 0.05 | 10 | μA | DE = GND,(符号不可读)= VCC | 6 | |
| ESD HBM, pin to GND (RS-485 pins A, B) | -16 | 16 | kV | 管脚到地 | 6 | ||
| ESD IEC61000-4-2 air-gap discharge (RS-485 pins A, B) | -16 | 16 | kV | RS-485 管脚(A、B);IEC61000-4-2 间隙放电 | 6 | ||
| ESD IEC61000-4-2 contact discharge, half-duplex (RS-485 pins A, B) | -16 | 16 | kV | RS-485 管脚(A、B);IEC61000-4-2 接触,半双工 | 6 | ||
| Driver standby time | tSHDN | 50 | 350 | 700 | ns | 9 | |
| Receiver standby time | tSHDN | 50 | 350 | 700 | ns | 注释 4 | 9 |
| Supply voltage (absolute maximum) | VCC | 6 | V | 4 | |||
| Control input voltage (RE, DE) | RE, DE | -0.3 | 6 | V | 4 | ||
| Driver input voltage | DI | -0.3 | 6 | V | 4 | ||
| Driver output voltage | A, B | -7 | 12 | V | 4 | ||
| Receiver input voltage | A, B | -7 | 12 | V | 4 | ||
| Receiver output voltage | RO | -0.3 | V | 4 | |||
| Operating temperature (industrial, EI grade) | -40 | 85 | ℃ | SN65HVDxxEI | 4 | ||
| Storage temperature | -65 | 150 | ℃ | 4 | |||
| Lead temperature (soldering) | TLEAD | 260 | ℃ | 焊接 10s | 4 |
CAD (KiCad official)
- Symbol:
SN65HVD78EIMM - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
sn65hvd78eimm-etched.step/sn65hvd78eimm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn65hvd78eimm.step/sn65hvd78eimm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (20 pp, sha256
81ed86cf3caebd1f, retrieved 2026-11-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).