main
History Download
Ray Publish 0.1.0 c958b28

SL27624MS

Slkor(SLKORMICRO Elec.) · Gate Drive ICs · SOP-8

SL27624MS from Slkor(SLKORMICRO Elec.), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ENA input Enable input for channel A: when ENA is low the channel A output is disabled regardless of INA, and the pin is internally pulled up to VDD (enable 200 kΩ pull-up), so it is enabled by default and should be tied to VDD if unused.
2 INA input Input of channel A, with OUTA in phase with INA; OUTA is held low when INA is floating due to the internal pull-down (120 kΩ), and INA should be connected to ground if unused.
3 GND power_in Ground; all signals are referenced to this pin.
4 INB input Input of channel B, with OUTB in phase with INB; OUTB is held low when INB is floating due to the internal pull-down (120 kΩ), and INB should be connected to ground if unused.
5 OUTB output Output of channel B, rail-to-rail between VDD and GND with 5.0 A peak source and 5.0 A peak sink capability at 12 V VDD.
6 VDD power_in Bias supply input; operates from 4.5 V to 30 V, and the SL27624M (this MPN's 8.5 V UVLO variant) holds outputs low below its rising UVLO threshold of 8 V to 9 V.
7 OUTA output Output of channel A, rail-to-rail between VDD and GND with 5.0 A peak source and 5.0 A peak sink capability at 12 V VDD.
8 ENB input Enable input for channel B: when ENB is low the channel B output is disabled regardless of INB, and the pin is internally pulled up to VDD (enable 200 kΩ pull-up), so it is enabled by default and should be tied to VDD if unused.

Key specifications

Parameter Value
Manufacturer Slkor(SLKORMICRO Elec.)
Package SOP-8
Category Power Management
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VDD -0.3 33 V 4
Voltage on INA, INB, ENA, ENB -6 33 V 4
Continuous voltage on OUTx OUTA, OUTB -0.3 V Continuous; upper limit printed as VDD+0.3 4
Repetitive pulse voltage on OUTx OUTA, OUTB -2 V Repetitive pulse less than 200ns; upper limit printed as VDD+0.3 4
Operation junction temperature range TJ -40 150 °C 4
Lead temperature TL 300 °C soldering, 10 seconds 4
Storage temperature TS -55 150 °C 4
Supply voltage VDD 4.5 30 V Over operating free-air temperature range 4
Input voltage INA, INB -5 30 V Over operating free-air temperature range 4
Enable voltage ENA, ENB -5 30 V Over operating free-air temperature range 4
Operation junction temperature range TJ -40 150 °C Over operating free-air temperature range 4
Rise time tR 7 11 ns VDD = 12V, CLOAD = 1.8 nF 5
Fall time tF 6 8.4 ns VDD = 12V, CLOAD = 1.8 nF 5
Minimum input pulse width that changes the output state tPW 13 15 ns VDD = 12V 5
Input to output propagation delay tD1, tD2 20 27 ns VDD = 12V, CLOAD = 1.8 nF, 5 V input pulse 5
EN to output propagation delay tD3, tD4 20 27 ns VDD = 12V, CLOAD = 1.8 nF, 5 V enable pulse 5
VDD startup current IVDD_OFF 110 270 μA VDD = 3.4 V, ENA = ENB = VDD, INA=INB=3.3V 5
VDD static current IVDD 810 1300 μA ENA=ENB=VDD, INA=INB=3.3V 5
VDD static current IVDD 600 900 μA ENA=ENB=VDD, INA=INB=0V 5
VDD operating current IVDD_OP 3.6 4.6 mA ENA=ENB=VDD, INA = INB = PWM, 1000kHz, no load at output 5
VDD disable current IVDD_DIS 630 900 μA INA=INB = 3.3 V, ENA = ENB = GND 5
VDD UVLO rising threshold VDD_UV_R 8 8.5 9 V SL27624M 5
VDD UVLO falling threshold VDD_UV_F 7 7.5 8 V SL27624 M 5
VDD UVLO hysteresis VDD_UV_HYS 1 V SL27624 M 6
Input signal high threshold VIN_H 1.8 2 2.3 V 6
Input signal low threshold VIN_L 0.8 1 1.2 V 6
Input signal hysteresis VIN_HYS 1 V 6
Inx pin pulldown resistor RIN 120 kΩ INx=3.3V 6
Enable signal high threshold VEN_H 1.8 2 2.3 V 6
Enable signal low threshold VEN_L 0.8 1 1.2 V 6
Enable signal hysteresis VEN_HYS 1 V 6
Enx pin pullup resistor REN 200 kΩ ENx=0V 6
Source peak current ISRC 5 A CL = 0.22 μF 6
Sink peak current ISNK 5 A CL = 0.22 μF 6
High level output voltage VOH 7.2 14 mV IO = -10 mA, VDD-VO 6
Low output voltage VOL 4.5 8.5 mV IO = 10 mA 6
Output pull-up resistance ROH 0.52 0.72 1.2 Ω IO = -10 mA 6
Output pull-down resistance ROL 0.26 0.45 0.74 Ω IO = 10 mA 6

CAD (KiCad official)

  • Symbol: SL27624MS
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: sl27624ms-etched.step / sl27624ms-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sl27624ms.step / sl27624ms.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Slkor(SLKORMICRO Elec.) datasheet (8 pp, sha256 b36e1b38f76db4d2, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus off (skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF