Generated by kicad-footprint-generator · KiCad file format 20260206
SI5395A-A-GM
Skyworks Solutions · Jitter Attenuators · QFN-64(9x9)
SI5395A-A-GM from Skyworks Solutions, in a QFN-64(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | input | Clock input 1, differential or single-ended, which is high-impedance and must be terminated externally. |
| 2 | IN1b | input | Complementary side of clock input 1; grounded through a capacitor when accepting a single-ended clock. |
| 3 | IN_SEL0 | input | Input reference select bit 0 for manual pin-controlled input selection per Table 4.1; internally pulled low. |
| 4 | IN_SEL1 | input | Input reference select bit 1 for manual pin-controlled input selection per Table 4.1. |
| 5 | RSVD | unconnected | Reserved pin connected to the die; leave disconnected. |
| 6 | RSTb | input | Active-low device reset that performs power-on reset and forces registers to default; clock outputs are disabled during reset and it is internally pulled up. |
| 7 | X1/NC | input | XTAL shield for grade A/B/C/D/P that connects directly to the XTAL ground pins and should be kept separate from the PCB ground plane. |
| 8 | XA/NC | input | Crystal input for grade A (XTAL), alternatively driven by an external REFCLK selected by register bit; default is XTAL mode. |
| 9 | XB/NC | input | Crystal input for grade A (XB) of the XTAL or REFCLK reference pair. |
| 10 | X2/NC | input | XTAL shield for grade A/B/C/D/P that connects directly to the XTAL ground pins. |
| 11 | OEb | input | Output enable pin that disables all outputs when held high; internally pulled low. |
| 12 | INTRb | output | Interrupt output asserted low when a change in device status occurs; leave unconnected when unused. |
| 13 | VDDA | power_in | Core supply pin requiring a 3.3 V source with a 1 µF bypass capacitor placed close to the pin. |
| 14 | IN2 | input | Clock input 2, differential or single-ended, which is high-impedance and must be terminated externally. |
| 15 | IN2b | input | Complementary side of clock input 2; grounded through a capacitor when accepting a single-ended clock. |
| 16 | SCLK | input | Serial clock input for both I2C and SPI modes, which must be pulled up by at least 1 kΩ in I2C mode. |
| 17 | A1/SDO | bidirectional | Address select 1 in I2C mode (open-drain, no internal pull) or serial data output SDO in 4-wire SPI mode, driving to the IO_VDD_SEL-selected voltage; leave disconnected when unused. |
| 18 | SDA/SDIO | bidirectional | Serial data pin: open-drain SDA in I2C mode requiring a pull-up of at least 1 kΩ, or SDIO in 3-wire SPI; tie low when unused. |
| 19 | A0/CSb | input | Hardware address select 0 in I2C mode or active-low chip select in SPI mode; internally pulled up by about 20 kΩ. |
| 20 | OUT0Ab | output | Complementary output clock 0A with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 21 | OUT0A | output | Output clock 0A with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 22 | VDDO0 | power_in | Output clock supply for OUT0 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 23 | OUT0b | output | Complementary output clock 0 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 24 | OUT0 | output | Output clock 0 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 25 | FDEC | input | Frequency decrement pin that steps down the frequency of a selected output by a register-configurable step; internally pulled low. |
| 26 | VDDO1 | power_in | Output clock supply for OUT1 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 27 | OUT1b | output | Complementary output clock 1 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 28 | OUT1 | output | Output clock 1 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 29 | VDDO2 | power_in | Output clock supply for OUT2 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 30 | OUT2b | output | Complementary output clock 2 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 31 | OUT2 | output | Output clock 2 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 32 | VDD | power_in | Core supply for the device, which operates from a 1.8 V supply with a 1.0 µF bypass capacitor placed close to the pin. |
| 33 | VDDO3 | power_in | Output clock supply for OUT3 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 34 | OUT3b | output | Complementary output clock 3 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 35 | OUT3 | output | Output clock 3 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 36 | VDDO4 | power_in | Output clock supply for OUT4 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 37 | OUT4b | output | Complementary output clock 4 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 38 | OUT4 | output | Output clock 4 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 39 | I2C_SEL | input | Serial interface select: I2C when high and SPI when low; internally pulled up by about 20 kΩ to the IO_VDD_SEL-selected voltage. |
| 40 | VDDO5 | power_in | Output clock supply for OUT5 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 41 | OUT5b | output | Complementary output clock 5 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 42 | OUT5 | output | Output clock 5 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 43 | VDDO6 | power_in | Output clock supply for OUT6 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 44 | OUT6b | output | Complementary output clock 6 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 45 | OUT6 | output | Output clock 6 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 46 | VDD | power_in | Core supply for the device, which operates from a 1.8 V supply with a 1.0 µF bypass capacitor placed close to the pin. |
| 47 | LOLb | output | Loss of lock output that is high when the DSPLL is locked and low when out-of-lock; may be left unconnected. |
| 48 | FINC | input | Frequency increment pin that steps up the frequency of a selected output by a register-configurable step; internally pulled low. |
| 49 | VDDO7 | power_in | Output clock supply for OUT7 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 50 | OUT7b | output | Complementary output clock 7 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 51 | OUT7 | output | Output clock 7 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 52 | VDDO8 | power_in | Output clock supply for OUT8 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 53 | OUT8b | output | Complementary output clock 8 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 54 | OUT8 | output | Output clock 8 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 55 | OUT9b | output | Complementary output clock 9 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 56 | OUT9 | output | Output clock 9 with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 57 | VDDO9 | power_in | Output clock supply for OUT9 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused. |
| 58 | OUT9Ab | output | Complementary output clock 9A with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 59 | OUT9A | output | Output clock 9A with programmable signal swing and common mode voltage; leave unconnected if unused. |
| 60 | VDD | power_in | Core supply for the device, which operates from a 1.8 V supply with a 1.0 µF bypass capacitor placed close to the pin. |
| 61 | IN3/FB_IN | input | Clock input 3 or external feedback input FB_IN for the optional zero delay mode; high-impedance and must be terminated externally. |
| 62 | IN3b/FB_INb | input | Complementary side of clock input 3 or of the external feedback input FB_INb used in zero delay mode. |
| 63 | IN0 | input | Clock input 0, differential or single-ended, which is high-impedance and must be terminated externally. |
| 64 | IN0b | input | Complementary side of clock input 0; grounded through a capacitor when accepting a single-ended clock. |
| 65 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Skyworks Solutions |
| Package | QFN-64(9x9) |
| Category | Clock And Timing |
| Pins | 65 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient Temperature | TA | -40 | 25 | 85 | °C | 24 | |
| Junction Temperature | TJMAX | 125 | °C | 24 | |||
| Core Supply Voltage | VDD | 1.71 | 1.8 | 1.89 | V | 24 | |
| Core Supply Voltage | VDDA | 3.14 | 3.3 | 3.47 | V | 24 | |
| Clock Output Driver Supply Voltage | VDDO | 3.14 | 3.3 | 3.47 | V | 24 | |
| Clock Output Driver Supply Voltage | VDDO | 2.37 | 2.5 | 2.62 | V | 24 | |
| Clock Output Driver Supply Voltage | VDDO | 1.71 | 1.8 | 1.89 | V | 24 | |
| Status Pin Supply Voltage | VDDS | 3.14 | 3.3 | 3.47 | V | 24 | |
| Status Pin Supply Voltage | VDDS | 1.71 | 1.8 | 1.89 | V | 24 | |
| Core Supply Current | IDD | 150 | 300 | mA | Si5395 | 25 | |
| Core Supply Current | IDDA | 125 | 140 | mA | Si5395 | 25 | |
| Output Buffer Supply Current | IDDOx | 22 | 26 | mA | 2.5 V LVPECL Output | 25 | |
| Output Buffer Supply Current | IDDOx | 15 | 18 | mA | 2.5 V LVDS Output | 25 | |
| Output Buffer Supply Current | IDDOx | 22 | 30 | mA | 3.3 V LVCMOS Output | 25 | |
| Output Buffer Supply Current | IDDOx | 18 | 23 | mA | 2.5 V LVCMOS Output | 25 | |
| Output Buffer Supply Current | IDDOx | 12 | 16 | mA | 1.8 V LVCMOS Output | 25 | |
| Total Power Dissipation | Pd | 1000 | 1400 | mW | Si5395 | 25 | |
| Input Frequency Range | fIN | 0.008 | 750 | MHz | Differential | 26 | |
| Input Frequency Range | fIN | 0.008 | 250 | MHz | All single-ended signals (including LVCMOS) | 26 | |
| Voltage Swing | VIN | 100 | 1800 | mVpp_se | Differential AC-coupled fIN < 250 MHz | 26 | |
| Voltage Swing | VIN | 225 | 1800 | mVpp_se | Differential AC-coupled 250 MHz < fIN < 750 MHz | 26 | |
| Voltage Swing | VIN | 100 | 3600 | mVpp_se | Single-ended AC-coupled fIN < 250 MHz | 26 | |
| Slew Rate | SR | 400 | V/µs | 26 | |||
| Duty Cycle | DC | 40 | 60 | % | 26 | ||
| Input Voltage | VIL | 0.5 | V | Standard CMOS | 26 | ||
| Input Voltage | VIL | 0.4 | V | Non-standard CMOS & Pulsed CMOS | 26 | ||
| Input Voltage | VIH | 1.3 | V | Standard CMOS | 26 | ||
| Input Voltage | VIH | 0.8 | V | Non-standard CMOS & Pulsed CMOS | 26 | ||
| Input Frequency | fIN_CMOS | 0.008 | 250 | MHz | Standard CMOS & Non-standard CMOS | 26 | |
| Input Frequency | fIN_CMOS | 0.008 | 1 | MHz | Pulsed CMOS | 26 | |
| Duty Cycle | DC | 5 | 95 | % | Pulsed CMOS | 26 | |
| Minimum Pulse Width | PW | 1.6 | ns | Standard CMOS & Non-standard CMOS (250 MHz @ 40% Duty Cycle) | 26 | ||
| Minimum Pulse Width | PW | 50 | ns | Pulsed CMOS (1 MHz @ 40% Duty Cycle) | 26 | ||
| Minimum Pulse Width | PW | 100 | ns | RSTb, FINC and FDEC | 28 | ||
| Update Rate | TUR | 1 | µs | FINC and FDEC | 28 | ||
| PLL Loop Bandwidth Programming Range | fBW | 0.1 | 4000 | Hz | 34 | ||
| Initial Start-Up Time | tSTART | 30 | 45 | ms | Grade A/B/C/D/J/K/L/M; time from power-up to free-running clocks | 34 | |
| PLL Lock Time | tACQ | 280 | 300 | ms | With Fastlock enabled, fIN = 19.44 MHz | 34 | |
| Maximum Phase Transient During a Hitless Switch | tSWITCH | 1.5 | ns | Single automatic/manual switch between two 8 kHz inputs, DSPLL BW = 40 Hz | 34 | ||
| Maximum Phase Transient During a Hitless Switch | tSWITCH | 0.3 | ns | Single automatic/manual switch between two 2 MHz inputs, DSPLL BW = 400 Hz | 34 | ||
| RMS Phase Jitter (Grade A/B/C/D and J/K/L/M) | JGEN | 85 | 120 | fs | Output divider Integer Mode | 35 | |
| RMS Phase Jitter (Grade A/B/C/D and J/K/L/M) | JGEN | 115 | 170 | fs | Output divider Fractional Mode/DCO Mode | 35 | |
| Jitter Peaking | JPK | 0.1 | dB | Measured with a frequency plan running a 25 MHz input, 25 MHz output, and a Loop Bandwidth of 4 Hz | 34 | ||
| Zero Delay Mode Input-to-Output Delay Variation | tZDELAY | 0.2 | ns | Between reference and feedback input with both clocks in LVDS differential format at 128 kHz | 34 | ||
| Crystal Frequency Range (A/B/C/D) | fXTAL | 24.97 | 54.06 | MHz | Full operating range. Jitter performance may be reduced. | 39 | |
| Crystal Frequency Range for best jitter | fXTAL | 48 | 54 | MHz | Range for best jitter | 39 | |
| Crystal Drive Level | dL | 200 | µW | 39 | |||
| Thermal Resistance Junction to Ambient (64-QFN) | θJA | 22 | °C/W | Still Air | 40 | ||
| Thermal Resistance Junction to Ambient (64-QFN) | θJA | 19.4 | °C/W | Air Flow 1 m/s | 40 | ||
| Thermal Resistance Junction to Ambient (64-QFN) | θJA | 18.3 | °C/W | Air Flow 2 m/s | 40 | ||
| Thermal Resistance Junction to Case (64-QFN) | θJC | 9.5 | °C/W | 40 | |||
| DC Supply Voltage | VDD | -0.5 | 3.8 | V | 41 | ||
| Input Voltage Range | VI1 | -1 | 3.8 | V | IN0-IN3/FB_IN | 41 | |
| Input Voltage Range | VI2 | -0.5 | 3.8 | V | IN_SEL1, IN_SEL0, RSTb, OEb, I2C_SEL, FINC, FDEC, SDI, SCLK, A0/CSb, A1, SDA/SDIO | 41 | |
| Input Voltage Range | VI3 | -0.5 | 2.7 | V | XA/XB | 41 | |
| Storage Temperature Range | TSTG | -55 | 150 | °C | 41 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. | 52 |
CAD (KiCad official)
- Symbol:
SI5395A-A-GM - Footprint:
Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm - 3D model: QFN-64(9x9) (KiCad packages3D, STEP)
- 3D model files:
si5395a-a-gm-etched.step/si5395a-a-gm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si5395a-a-gm.step/si5395a-a-gm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Skyworks Solutions datasheet (61 pp, sha256
8c7e4afa37970e35, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).