Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SI5395A-A-GM

Skyworks Solutions · Jitter Attenuators · QFN-64(9x9)

SI5395A-A-GM from Skyworks Solutions, in a QFN-64(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN1 input Clock input 1, differential or single-ended, which is high-impedance and must be terminated externally.
2 IN1b input Complementary side of clock input 1; grounded through a capacitor when accepting a single-ended clock.
3 IN_SEL0 input Input reference select bit 0 for manual pin-controlled input selection per Table 4.1; internally pulled low.
4 IN_SEL1 input Input reference select bit 1 for manual pin-controlled input selection per Table 4.1.
5 RSVD unconnected Reserved pin connected to the die; leave disconnected.
6 RSTb input Active-low device reset that performs power-on reset and forces registers to default; clock outputs are disabled during reset and it is internally pulled up.
7 X1/NC input XTAL shield for grade A/B/C/D/P that connects directly to the XTAL ground pins and should be kept separate from the PCB ground plane.
8 XA/NC input Crystal input for grade A (XTAL), alternatively driven by an external REFCLK selected by register bit; default is XTAL mode.
9 XB/NC input Crystal input for grade A (XB) of the XTAL or REFCLK reference pair.
10 X2/NC input XTAL shield for grade A/B/C/D/P that connects directly to the XTAL ground pins.
11 OEb input Output enable pin that disables all outputs when held high; internally pulled low.
12 INTRb output Interrupt output asserted low when a change in device status occurs; leave unconnected when unused.
13 VDDA power_in Core supply pin requiring a 3.3 V source with a 1 µF bypass capacitor placed close to the pin.
14 IN2 input Clock input 2, differential or single-ended, which is high-impedance and must be terminated externally.
15 IN2b input Complementary side of clock input 2; grounded through a capacitor when accepting a single-ended clock.
16 SCLK input Serial clock input for both I2C and SPI modes, which must be pulled up by at least 1 kΩ in I2C mode.
17 A1/SDO bidirectional Address select 1 in I2C mode (open-drain, no internal pull) or serial data output SDO in 4-wire SPI mode, driving to the IO_VDD_SEL-selected voltage; leave disconnected when unused.
18 SDA/SDIO bidirectional Serial data pin: open-drain SDA in I2C mode requiring a pull-up of at least 1 kΩ, or SDIO in 3-wire SPI; tie low when unused.
19 A0/CSb input Hardware address select 0 in I2C mode or active-low chip select in SPI mode; internally pulled up by about 20 kΩ.
20 OUT0Ab output Complementary output clock 0A with programmable signal swing and common mode voltage; leave unconnected if unused.
21 OUT0A output Output clock 0A with programmable signal swing and common mode voltage; leave unconnected if unused.
22 VDDO0 power_in Output clock supply for OUT0 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
23 OUT0b output Complementary output clock 0 with programmable signal swing and common mode voltage; leave unconnected if unused.
24 OUT0 output Output clock 0 with programmable signal swing and common mode voltage; leave unconnected if unused.
25 FDEC input Frequency decrement pin that steps down the frequency of a selected output by a register-configurable step; internally pulled low.
26 VDDO1 power_in Output clock supply for OUT1 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
27 OUT1b output Complementary output clock 1 with programmable signal swing and common mode voltage; leave unconnected if unused.
28 OUT1 output Output clock 1 with programmable signal swing and common mode voltage; leave unconnected if unused.
29 VDDO2 power_in Output clock supply for OUT2 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
30 OUT2b output Complementary output clock 2 with programmable signal swing and common mode voltage; leave unconnected if unused.
31 OUT2 output Output clock 2 with programmable signal swing and common mode voltage; leave unconnected if unused.
32 VDD power_in Core supply for the device, which operates from a 1.8 V supply with a 1.0 µF bypass capacitor placed close to the pin.
33 VDDO3 power_in Output clock supply for OUT3 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
34 OUT3b output Complementary output clock 3 with programmable signal swing and common mode voltage; leave unconnected if unused.
35 OUT3 output Output clock 3 with programmable signal swing and common mode voltage; leave unconnected if unused.
36 VDDO4 power_in Output clock supply for OUT4 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
37 OUT4b output Complementary output clock 4 with programmable signal swing and common mode voltage; leave unconnected if unused.
38 OUT4 output Output clock 4 with programmable signal swing and common mode voltage; leave unconnected if unused.
39 I2C_SEL input Serial interface select: I2C when high and SPI when low; internally pulled up by about 20 kΩ to the IO_VDD_SEL-selected voltage.
40 VDDO5 power_in Output clock supply for OUT5 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
41 OUT5b output Complementary output clock 5 with programmable signal swing and common mode voltage; leave unconnected if unused.
42 OUT5 output Output clock 5 with programmable signal swing and common mode voltage; leave unconnected if unused.
43 VDDO6 power_in Output clock supply for OUT6 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
44 OUT6b output Complementary output clock 6 with programmable signal swing and common mode voltage; leave unconnected if unused.
45 OUT6 output Output clock 6 with programmable signal swing and common mode voltage; leave unconnected if unused.
46 VDD power_in Core supply for the device, which operates from a 1.8 V supply with a 1.0 µF bypass capacitor placed close to the pin.
47 LOLb output Loss of lock output that is high when the DSPLL is locked and low when out-of-lock; may be left unconnected.
48 FINC input Frequency increment pin that steps up the frequency of a selected output by a register-configurable step; internally pulled low.
49 VDDO7 power_in Output clock supply for OUT7 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
50 OUT7b output Complementary output clock 7 with programmable signal swing and common mode voltage; leave unconnected if unused.
51 OUT7 output Output clock 7 with programmable signal swing and common mode voltage; leave unconnected if unused.
52 VDDO8 power_in Output clock supply for OUT8 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
53 OUT8b output Complementary output clock 8 with programmable signal swing and common mode voltage; leave unconnected if unused.
54 OUT8 output Output clock 8 with programmable signal swing and common mode voltage; leave unconnected if unused.
55 OUT9b output Complementary output clock 9 with programmable signal swing and common mode voltage; leave unconnected if unused.
56 OUT9 output Output clock 9 with programmable signal swing and common mode voltage; leave unconnected if unused.
57 VDDO9 power_in Output clock supply for OUT9 outputs at 3.3 V, 2.5 V or 1.8 V; leave unconnected if unused.
58 OUT9Ab output Complementary output clock 9A with programmable signal swing and common mode voltage; leave unconnected if unused.
59 OUT9A output Output clock 9A with programmable signal swing and common mode voltage; leave unconnected if unused.
60 VDD power_in Core supply for the device, which operates from a 1.8 V supply with a 1.0 µF bypass capacitor placed close to the pin.
61 IN3/FB_IN input Clock input 3 or external feedback input FB_IN for the optional zero delay mode; high-impedance and must be terminated externally.
62 IN3b/FB_INb input Complementary side of clock input 3 or of the external feedback input FB_INb used in zero delay mode.
63 IN0 input Clock input 0, differential or single-ended, which is high-impedance and must be terminated externally.
64 IN0b input Complementary side of clock input 0; grounded through a capacitor when accepting a single-ended clock.
65 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Skyworks Solutions
Package QFN-64(9x9)
Category Clock And Timing
Pins 65

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient Temperature TA -40 25 85 °C 24
Junction Temperature TJMAX 125 °C 24
Core Supply Voltage VDD 1.71 1.8 1.89 V 24
Core Supply Voltage VDDA 3.14 3.3 3.47 V 24
Clock Output Driver Supply Voltage VDDO 3.14 3.3 3.47 V 24
Clock Output Driver Supply Voltage VDDO 2.37 2.5 2.62 V 24
Clock Output Driver Supply Voltage VDDO 1.71 1.8 1.89 V 24
Status Pin Supply Voltage VDDS 3.14 3.3 3.47 V 24
Status Pin Supply Voltage VDDS 1.71 1.8 1.89 V 24
Core Supply Current IDD 150 300 mA Si5395 25
Core Supply Current IDDA 125 140 mA Si5395 25
Output Buffer Supply Current IDDOx 22 26 mA 2.5 V LVPECL Output 25
Output Buffer Supply Current IDDOx 15 18 mA 2.5 V LVDS Output 25
Output Buffer Supply Current IDDOx 22 30 mA 3.3 V LVCMOS Output 25
Output Buffer Supply Current IDDOx 18 23 mA 2.5 V LVCMOS Output 25
Output Buffer Supply Current IDDOx 12 16 mA 1.8 V LVCMOS Output 25
Total Power Dissipation Pd 1000 1400 mW Si5395 25
Input Frequency Range fIN 0.008 750 MHz Differential 26
Input Frequency Range fIN 0.008 250 MHz All single-ended signals (including LVCMOS) 26
Voltage Swing VIN 100 1800 mVpp_se Differential AC-coupled fIN < 250 MHz 26
Voltage Swing VIN 225 1800 mVpp_se Differential AC-coupled 250 MHz < fIN < 750 MHz 26
Voltage Swing VIN 100 3600 mVpp_se Single-ended AC-coupled fIN < 250 MHz 26
Slew Rate SR 400 V/µs 26
Duty Cycle DC 40 60 % 26
Input Voltage VIL 0.5 V Standard CMOS 26
Input Voltage VIL 0.4 V Non-standard CMOS & Pulsed CMOS 26
Input Voltage VIH 1.3 V Standard CMOS 26
Input Voltage VIH 0.8 V Non-standard CMOS & Pulsed CMOS 26
Input Frequency fIN_CMOS 0.008 250 MHz Standard CMOS & Non-standard CMOS 26
Input Frequency fIN_CMOS 0.008 1 MHz Pulsed CMOS 26
Duty Cycle DC 5 95 % Pulsed CMOS 26
Minimum Pulse Width PW 1.6 ns Standard CMOS & Non-standard CMOS (250 MHz @ 40% Duty Cycle) 26
Minimum Pulse Width PW 50 ns Pulsed CMOS (1 MHz @ 40% Duty Cycle) 26
Minimum Pulse Width PW 100 ns RSTb, FINC and FDEC 28
Update Rate TUR 1 µs FINC and FDEC 28
PLL Loop Bandwidth Programming Range fBW 0.1 4000 Hz 34
Initial Start-Up Time tSTART 30 45 ms Grade A/B/C/D/J/K/L/M; time from power-up to free-running clocks 34
PLL Lock Time tACQ 280 300 ms With Fastlock enabled, fIN = 19.44 MHz 34
Maximum Phase Transient During a Hitless Switch tSWITCH 1.5 ns Single automatic/manual switch between two 8 kHz inputs, DSPLL BW = 40 Hz 34
Maximum Phase Transient During a Hitless Switch tSWITCH 0.3 ns Single automatic/manual switch between two 2 MHz inputs, DSPLL BW = 400 Hz 34
RMS Phase Jitter (Grade A/B/C/D and J/K/L/M) JGEN 85 120 fs Output divider Integer Mode 35
RMS Phase Jitter (Grade A/B/C/D and J/K/L/M) JGEN 115 170 fs Output divider Fractional Mode/DCO Mode 35
Jitter Peaking JPK 0.1 dB Measured with a frequency plan running a 25 MHz input, 25 MHz output, and a Loop Bandwidth of 4 Hz 34
Zero Delay Mode Input-to-Output Delay Variation tZDELAY 0.2 ns Between reference and feedback input with both clocks in LVDS differential format at 128 kHz 34
Crystal Frequency Range (A/B/C/D) fXTAL 24.97 54.06 MHz Full operating range. Jitter performance may be reduced. 39
Crystal Frequency Range for best jitter fXTAL 48 54 MHz Range for best jitter 39
Crystal Drive Level dL 200 µW 39
Thermal Resistance Junction to Ambient (64-QFN) θJA 22 °C/W Still Air 40
Thermal Resistance Junction to Ambient (64-QFN) θJA 19.4 °C/W Air Flow 1 m/s 40
Thermal Resistance Junction to Ambient (64-QFN) θJA 18.3 °C/W Air Flow 2 m/s 40
Thermal Resistance Junction to Case (64-QFN) θJC 9.5 °C/W 40
DC Supply Voltage VDD -0.5 3.8 V 41
Input Voltage Range VI1 -1 3.8 V IN0-IN3/FB_IN 41
Input Voltage Range VI2 -0.5 3.8 V IN_SEL1, IN_SEL0, RSTb, OEb, I2C_SEL, FINC, FDEC, SDI, SCLK, A0/CSb, A1, SDA/SDIO 41
Input Voltage Range VI3 -0.5 2.7 V XA/XB 41
Storage Temperature Range TSTG -55 150 °C 41

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing PC 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 52

CAD (KiCad official)

  • Symbol: SI5395A-A-GM
  • Footprint: Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm
  • 3D model: QFN-64(9x9) (KiCad packages3D, STEP)
  • 3D model files: si5395a-a-gm-etched.step / si5395a-a-gm-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si5395a-a-gm.step / si5395a-a-gm.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Skyworks Solutions datasheet (61 pp, sha256 8c7e4afa37970e35, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF