3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSI5341B-D-GM
SILICON LABS · Clock Generators / Frequency Synthesizers / PLL · QFN-64-EP(9x9)
SI5341B-D-GM from SILICON LABS, in a QFN-64-EP(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | input | Clock input IN1 accepts differential or single-ended clocks, is high-impedance and must be terminated externally. |
| 2 | IN1b | input | Complementary clock input IN1b of the IN1 pair, is high-impedance and must be terminated externally. |
| 3 | IN_SEL0 | input | Input reference select bit 0 that, with IN_SEL1, chooses the active clock input in manual pin-controlled mode; internally pulled up with ~20 kΩ to the IO_VDD_SEL-selected voltage. |
| 4 | IN_SEL1 | input | Input reference select bit 1 that, with IN_SEL0, chooses the active clock input in manual pin-controlled mode; internally pulled up with ~20 kΩ to the IO_VDD_SEL-selected voltage. |
| 5 | SYNCb | input | Active-low output clock synchronization input that resets the output dividers to re-align output clocks; internally pulled up with ~20 kΩ and may be left unconnected. |
| 6 | RSTb | input | Active-low device reset input that performs power-on reset, forces registers to default values and disables clock outputs during reset; internally pulled up with ~20 kΩ. |
| 7 | X1 | input | XTAL shield pin that must connect directly to the XTAL ground pins, must not be connected to the PCB ground plane, and is left disconnected when XA/XB is driven by an external clock. |
| 8 | XA | input | Crystal and external clock input of the XA/XB pair, selected when IN_SEL[1:0] = 11b, and may be left unconnected if unused and powered down. |
| 9 | XB | input | Complementary crystal and external clock input of the XA/XB pair, selected when IN_SEL[1:0] = 11b, and may be left unconnected if unused and powered down. |
| 10 | X2 | input | XTAL shield pin that must connect directly to the XTAL ground pins, must not be connected to the PCB ground plane, and is left disconnected when XA/XB is driven by an external clock. |
| 11 | OEb | input | Output enable input that disables all outputs when held high; internally pulled low and may be left unconnected. |
| 12 | INTRb | output | Interrupt output asserted low when a device status change occurs; push-pull output that may be left unconnected when not in use. |
| 13 | VDDA | power_in | Core supply pin that requires a 3.3 V power source, with a 1.0 µF bypass capacitor recommended. |
| 14 | IN2 | input | Clock input IN2 accepts differential or single-ended clocks, is high-impedance and must be terminated externally. |
| 15 | IN2b | input | Complementary clock input IN2b of the IN2 pair, is high-impedance and must be terminated externally. |
| 16 | SCLK | input | Serial clock input for I2C and SPI modes; internally pulled up with ~20 kΩ and requires an external pull-up of at least 1 kΩ in I2C mode. |
| 17 | A1/SDO | bidirectional | Address select A1 input in I2C mode with no internal pull-up or pull-down, and serial data output (SDO) in 4-wire SPI mode that drives high to the IO_VDD_SEL-selected voltage. |
| 18 | SDA/SDIO | bidirectional | Serial data pin (SDA) in I2C mode, which requires an external pull-up of at least 1 kΩ; SDIO in 3-wire SPI and SDI in 4-wire SPI, with no pull-up needed in SPI mode. |
| 19 | A0/CSb | input | Hardware address select A0 in I2C mode and active-low chip select in SPI mode; internally pulled up with ~20 kΩ to the IO_VDD_SEL-selected voltage. |
| 20 | RSVD | unconnected | Reserved pin connected to the die that must be left disconnected. |
| 21 | RSVD | unconnected | Reserved pin connected to the die that must be left disconnected. |
| 22 | VDDO0 | power_in | Output clock supply for OUT0 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 23 | OUT0b | output | Complementary output clock 0 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 24 | OUT0 | output | Output clock 0 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 25 | FDEC | input | Frequency decrement input that steps down the output frequency of a selected output; internally pulled low with ~20 kΩ and may be left unconnected. |
| 26 | VDDO1 | power_in | Output clock supply for OUT1 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 27 | OUT1b | output | Complementary output clock 1 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 28 | OUT1 | output | Output clock 1 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 29 | VDDO2 | power_in | Output clock supply for OUT2 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 30 | OUT2b | output | Complementary output clock 2 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 31 | OUT2 | output | Output clock 2 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 32 | VDD | power_in | Core supply voltage that operates from a 1.8 V supply, with a 1.0 µF bypass capacitor recommended. |
| 33 | VDDO3 | power_in | Output clock supply for OUT3 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 34 | OUT3b | output | Complementary output clock 3 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 35 | OUT3 | output | Output clock 3 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 36 | VDDO4 | power_in | Output clock supply for OUT4 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 37 | OUT4b | output | Complementary output clock 4 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 38 | OUT4 | output | Output clock 4 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 39 | I2C_SEL | input | Serial interface mode select: I2C when high (I2C_SEL = 1) and SPI when low (I2C_SEL = 0); internally pulled up with ~20 kΩ to the IO_VDD_SEL-selected voltage. |
| 40 | VDDO5 | power_in | Output clock supply for OUT5 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 41 | OUT5b | output | Complementary output clock 5 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 42 | OUT5 | output | Output clock 5 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 43 | VDDO6 | power_in | Output clock supply for OUT6 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 44 | OUT6b | output | Complementary output clock 6 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 45 | OUT6 | output | Output clock 6 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 46 | VDD | power_in | Core supply voltage that operates from a 1.8 V supply, with a 1.0 µF bypass capacitor recommended. |
| 47 | LOLb | output | Loss of lock output that is high when the DSPLL is locked and low when out-of-lock; push-pull and needs no external pull-up or pull-down. |
| 48 | FINC | input | Frequency increment input that steps up the output frequency of a selected output; internally pulled low with ~20 kΩ and may be left unconnected. |
| 49 | VDDO7 | power_in | Output clock supply for OUT7 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 50 | OUT7b | output | Complementary output clock 7 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 51 | OUT7 | output | Output clock 7 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 52 | VDDO8 | power_in | Output clock supply for OUT8 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 53 | OUT8b | output | Complementary output clock 8 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 54 | OUT8 | output | Output clock 8 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 55 | RSVD | unconnected | Reserved pin connected to the die that must be left disconnected. |
| 56 | RSVD | unconnected | Reserved pin connected to the die that must be left disconnected. |
| 57 | VDDO9 | power_in | Output clock supply for OUT9 driver at 3.3 V, 2.5 V or 1.8 V; leave unconnected if the output driver is unused. |
| 58 | OUT9b | output | Complementary output clock 9 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 59 | OUT9 | output | Output clock 9 with programmable signal amplitude in differential mode; leave unconnected if unused. |
| 60 | VDD | power_in | Core supply voltage that operates from a 1.8 V supply, with a 1.0 µF bypass capacitor recommended. |
| 61 | FB_IN | input | External feedback input for the optional zero delay mode; may be left floating if unused and powered down. |
| 62 | FB_INb | input | Complementary external feedback input for the optional zero delay mode; may be left floating if unused and powered down. |
| 63 | IN0 | input | Clock input IN0 accepts differential or single-ended clocks, is high-impedance and must be terminated externally. |
| 64 | IN0b | input | Complementary clock input IN0b of the IN0 pair, is high-impedance and must be terminated externally. |
| 65 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-64-EP(9x9) |
| Category | Clock and Timing |
| Pins | 65 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient Temperature | TA | -40 | 25 | 85 | °C | 17 | |
| Junction Temperature | TJMAX | 125 | °C | 17 | |||
| Core Supply Voltage | VDD | 1.71 | 1.8 | 1.89 | V | 17 | |
| Core Supply Voltage 3.3 V | VDDA | 3.14 | 3.3 | 3.47 | V | 17 | |
| Output Driver Supply Voltage (3.3 V row) | VDDO | 3.14 | 3.3 | 3.47 | V | 17 | |
| Output Driver Supply Voltage (2.5 V row) | VDDO | 2.37 | 2.5 | 2.62 | V | 17 | |
| Output Driver Supply Voltage (1.8 V row) | VDDO | 1.71 | 1.8 | 1.89 | V | 17 | |
| Core Supply Current | IDD | 115 | 230 | mA | Si5340/41 | 18 | |
| Core Analog Supply Current | IDDA | 120 | 130 | mA | Si5340/41 | 18 | |
| Output Buffer Supply Current (LVPECL output) | IDDOx | 22 | 26 | mA | LVPECL Output @ 156.25 MHz | 18 | |
| Output Buffer Supply Current (LVDS output) | IDDOx | 15 | 18 | mA | LVDS Output @ 156.25 MHz | 18 | |
| Output Buffer Supply Current (3.3 V LVCMOS output) | IDDOx | 22 | 30 | mA | 3.3 V LVCMOS output @ 156.25 MHz | 18 | |
| Output Buffer Supply Current (2.5 V LVCMOS output) | IDDOx | 18 | 23 | mA | 2.5 V LVCMOS output @ 156.25 MHz | 18 | |
| Output Buffer Supply Current (1.8 V LVCMOS output) | IDDOx | 12 | 16 | mA | 1.8 V LVCMOS output @ 156.25 MHz | 18 | |
| Total Power Dissipation | Pd | 880 | 1150 | mW | Si5341; 7 x 2.5 V LVDS outputs enabled @ 156.25 MHz, excludes termination power | 18 | |
| Input Frequency Range (differential) | fIN | 10 | 750 | MHz | Differential | 19 | |
| Input Frequency Range (single-ended, including LVCMOS) | fIN | 10 | 250 | MHz | All single-ended signals (including LVCMOS) | 19 | |
| Input Voltage Swing (differential AC-coupled) | VIN | 100 | 1800 | mVpp_se | Differential AC-coupled, fIN < 250 MHz | 19 | |
| Input Voltage Swing (differential AC-coupled) | VIN | 225 | 1800 | mVpp_se | Differential AC-coupled, 250 MHz < fIN < 750 MHz | 19 | |
| Input Voltage Swing (single-ended AC-coupled) | VIN | 100 | 3600 | mVpp_se | Single-ended AC-coupled, fIN < 250 MHz | 19 | |
| Input Slew Rate (REFCLK, XA/XB) | SR | 400 | V/μs | Imposed for best jitter performance | 19 | ||
| Input Voltage Low (pulsed CMOS, IN0-IN2) | VIL | -0.2 | 0.4 | V | Pulsed CMOS Input Buffer - DC Coupled | 19 | |
| Input Voltage High (pulsed CMOS, IN0-IN2) | VIH | 0.8 | V | Pulsed CMOS Input Buffer - DC Coupled | 19 | ||
| Minimum Pulse Width (pulsed CMOS input) | PW | 1.6 | ns | Pulse Input | 19 | ||
| REFCLK Input Frequency (full operating range) | fIN | 10 | 200 | MHz | Full operating range; jitter performance may be reduced | 19 | |
| REFCLK Input Frequency (range for best jitter) | fIN | 48 | 54 | MHz | Range for best jitter | 19 | |
| REFCLK Input Single-ended Voltage Swing | VIN_SE | 365 | 2000 | mVpp_se | 19 | ||
| REFCLK Input Differential Voltage Swing | VIN_DIFF | 365 | 2500 | mVpp_diff | 19 | ||
| REFCLK Input Duty Cycle | DC | 40 | 60 | % | 19 | ||
| Frequency Update Rate | FUR | 1 | MHz | FINC and FDEC | 20 | ||
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | 400 | 600 | ps | VDDO = 3.3 V, 20% to 80% | 23 | |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | 450 | 600 | ps | VDDO = 2.5 V, 20% to 80% | 23 | |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | 550 | 750 | ps | VDDO = 1.8 V, 20% to 80% | 23 | |
| Initial Start-Up Time | tSTART | 30 | 45 | ms | Time from power-up to when device generates clocks (input frequency > 48 MHz) | 24 | |
| PLL Lock Time | tACQ | 15 | 150 | ms | fIN = 19.44 MHz | 24 | |
| Jitter Generation (locked to external clock, integer mode) | JGEN | 140 | 180 | fs rms | Locked to external clock; fIN = 100 MHz, fOUT = 156.25 MHz LVPECL; integer mode; 12 kHz to 20 MHz | 25 | |
| Jitter Generation (locked to external clock, fractional/DCO mode) | JGEN | 160 | 210 | fs rms | Locked to external clock; fIN = 100 MHz, fOUT = 156.25 MHz LVPECL; fractional/DCO mode; 12 kHz to 20 MHz | 25 | |
| Jitter Generation (locked to 48 MHz XTAL, integer mode) | JGEN | 90 | 140 | fs rms | Locked to external XTAL, XTAL = 48 MHz; integer mode; 12 kHz to 20 MHz | 25 | |
| Jitter Generation (locked to 48 MHz XTAL, fractional/DCO mode) | JGEN | 115 | 170 | fs rms | Locked to external XTAL, XTAL = 48 MHz; fractional/DCO mode; 12 kHz to 20 MHz | 25 | |
| SCLK Frequency (3-wire SPI) | fSPI | 20 | MHz | 29 | |||
| SCLK Duty Cycle (3-wire SPI) | TDC | 40 | 60 | % | 29 | ||
| SCLK Period (3-wire SPI) | TC | 50 | ns | 29 | |||
| Delay Time, SCLK Fall to SDO Turn-on (3-wire SPI) | TD1 | 12.5 | 20 | ns | 29 | ||
| Crystal Frequency Range | fXTAL | 24.97 | 54.06 | MHz | Full operating range; jitter performance may be reduced | 30 | |
| Crystal Frequency Range (best jitter) | fXTAL | 48 | 54 | MHz | Range for best jitter | 30 | |
| Storage Temperature Range | TSTG | -55 | 150 | °C | 31 | ||
| DC Supply Voltage (core) | VDD | -0.5 | 3.8 | V | 31 | ||
| DC Supply Voltage (VDDA) | VDDA | -0.5 | 3.8 | V | 31 | ||
| DC Supply Voltage (VDDO) | VDDO | -0.5 | 3.8 | V | 31 | ||
| Input Voltage Range (IN0-IN2, FB_IN) | VI1 | -1 | 3.8 | V | IN0-IN2, FB_IN | 31 | |
| Input Voltage Range (control pins) | VI2 | -0.5 | 3.8 | V | IN_SEL[1:0], RSTb, OEb, SYNCb, I2C_SEL, SDI, SCLK, A0/CSb, A1, SDA/SDIO, FINC/FDEC | 31 | |
| Input Voltage Range (XA/XB) | VI3 | -0.5 | 2.7 | V | XA/XB | 31 | |
| ESD Tolerance (HBM) | 2 | kV | HBM 100 pF, 1.5 kΩ | 31 | |||
| Maximum Junction Temperature in Operation | TJCT | 125 | °C | 31 | |||
| Soldering Temperature (Pb-free profile) | TPEAK | 260 | °C | 31 | |||
| Thermal Resistance Junction to Ambient | ϴJA | 22 | °C/W | Still air; Si5341 64QFN; PCB 3 in x 4.5 in, 4-layer | 30 | ||
| Thermal Resistance Junction to Case | ϴJC | 9.5 | °C/W | Si5341 64QFN | 30 | ||
| Thermal Resistance Junction to Board | ϴJB | 9.4 | °C/W | Si5341 64QFN | 30 | ||
| Thermal Characterization Parameter Junction to Board | ΨJB | 9.3 | °C/W | Si5341 64QFN | 30 | ||
| Thermal Characterization Parameter Junction to Top Center | ΨJT | 0.2 | °C/W | Si5341 64QFN | 30 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. | 42 |
CAD (KiCad official)
- Symbol:
SI5341B-D-GM - Footprint:
Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm - 3D model: QFN-64-EP(9x9) (KiCad packages3D, STEP)
- 3D model files:
si5341b-d-gm-etched.step/si5341b-d-gm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si5341b-d-gm.step/si5341b-d-gm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (49 pp, sha256
0b243d92e50b9eae, retrieved 2026-10-29, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).