main
Ray
Publish 0.1.0
4c621a3
SI5340A-D-GM
SILICON LABS · Clock Generators / Frequency Synthesizers / PLL · QFN-44-EP(7x7)
SI5340A-D-GM from SILICON LABS, in a QFN-44-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | input | Clock input IN1 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 2 | IN1b | input | Complementary clock input IN1b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 3 | IN_SEL0 | input | Input reference select bit 0 chooses the active clock input in manual pin-controlled mode and is internally pulled up with a ~20 kΩ resistor. |
| 4 | X1 | input | XTAL shield pin must be connected directly to the XTAL ground pins, must not be connected to the PCB ground plane, and should be left disconnected when XA/XB is driven by an external reference clock. |
| 5 | XA | input | Crystal and external clock input used to connect an external crystal or external clock, selected when IN_SEL[1:0] = 11b. |
| 6 | XB | input | Crystal and external clock input used with XA to connect an external crystal or external clock. |
| 7 | X2 | input | XTAL shield pin must be connected directly to the XTAL ground pins, must not be connected to the PCB ground plane, and should be left disconnected when XA/XB is driven by an external reference clock. |
| 8 | VDDA | power_in | Core supply pin requires a 3.3 V power source and a 1.0 µF bypass capacitor is recommended. |
| 9 | VDDA | power_in | Core supply pin requires a 3.3 V power source and a 1.0 µF bypass capacitor is recommended. |
| 10 | IN2 | input | Clock input IN2 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 11 | IN2b | input | Complementary clock input IN2b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 12 | OEb | input | Output enable input disables all outputs when held high and is internally pulled low, so it can be left unconnected when not in use. |
| 13 | SDA/SDIO | bidirectional | Bidirectional serial data pin (SDA in I2C mode, SDIO in 3-wire SPI) that requires an external pull-up of at least 1 kΩ in I2C mode and no pull-up in SPI mode. |
| 14 | SCLK | input | Serial clock input for I2C and SPI modes that requires an external pull-up of at least 1 kΩ in I2C mode and is internally pulled up with ~20 kΩ. |
| 15 | A1/SDO | bidirectional | Address select 1 in I2C mode with no internal pull resistor, and serial data output (SDO) in 4-wire SPI mode. |
| 16 | A0/CSb | input | Address select 0 in I2C mode and active-low chip select input in SPI mode, internally pulled up with ~20 kΩ. |
| 17 | RSTb | input | Active-low device reset input that performs power-on reset and forces registers to default values, with clock outputs disabled during reset; internally pulled up with ~20 kΩ. |
| 18 | VDDO0 | power_in | Output clock supply voltage for OUT0 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 19 | OUT0b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 20 | OUT0 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 21 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 22 | NC | unconnected | No connect pin that is not connected to the die and must be left disconnected. |
| 23 | VDDO1 | power_in | Output clock supply voltage for OUT1 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 24 | OUT1b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 25 | OUT1 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 26 | VDDS | power_in | Status output voltage supply that sets the VOL/VOH levels on LOLb and LOS_XAXBb and needs a 0.1 µF to 1.0 µF bypass capacitor. |
| 27 | LOLb | output | Loss of lock output that is high when the DSPLL is locked and low when out-of-lock, requiring no external pull-up or pull-down. |
| 28 | LOS_XAXBb | output | Loss of signal output that indicates a loss of signal at the XA/XB pins. |
| 29 | VDDO2 | power_in | Output clock supply voltage for OUT2 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 30 | OUT2b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 31 | OUT2 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 32 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 33 | INTRb | output | Interrupt output asserted low when a change in device status occurs; it is push-pull and should be left unconnected when not in use. |
| 34 | VDDO3 | power_in | Output clock supply voltage for OUT3 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 35 | OUT3b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 36 | OUT3 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 37 | IN_SEL1 | input | Input reference select bit 1 chooses the active clock input in manual pin-controlled mode and is internally pulled up with a ~20 kΩ resistor. |
| 38 | I2C_SEL | input | Serial interface select that chooses I2C when high (1) and SPI when low (0), internally pulled up with ~20 kΩ. |
| 39 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 40 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 41 | FB_IN | input | External feedback input used with FB_INb for the optional zero delay mode and which can be left floating if unused and powered down. |
| 42 | FB_INb | input | Complementary external feedback input used with FB_IN for the optional zero delay mode and which can be left floating if unused and powered down. |
| 43 | IN0 | input | Clock input IN0 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 44 | IN0b | input | Complementary clock input IN0b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 45 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-44-EP(7x7) |
| Category | RTC/Clock Chip |
| Pins | 45 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient Temperature | TA | -40 | 25 | 85 | °C | 17 | |
| Junction Temperature | TJMAX | 125 | °C | 17 | |||
| Core Supply Voltage | VDD | 1.71 | 1.8 | 1.89 | V | 17 | |
| Core Supply Voltage 3.3 V | VDDA | 3.14 | 3.3 | 3.47 | V | 17 | |
| Output Driver Supply Voltage | VDDO | 3.14 | 3.3 | 3.47 | V | 17 | |
| Output Driver Supply Voltage | VDDO | 2.37 | 2.5 | 2.62 | V | 17 | |
| Output Driver Supply Voltage | VDDO | 1.71 | 1.8 | 1.89 | V | 17 | |
| Core Supply Current | IDD | 115 | 230 | mA | Si5340/41 | 18 | |
| Core Supply Current (analog) | IDDA | 120 | 130 | mA | Si5340/41 | 18 | |
| Total Power Dissipation | Pd | 680 | 875 | mW | Si5340 | 18 | |
| Input Frequency Range | fIN | 10 | 750 | MHz | Differential | 19 | |
| Input Frequency Range | fIN | 10 | 250 | MHz | All single-ended signals (including LVCMOS) | 19 | |
| Input Slew Rate | SR | 400 | V/μs | 19 | |||
| Pulsed CMOS Input Low Voltage | VIL | -0.2 | 0.4 | V | Pulsed CMOS input buffer, DC coupled (IN0, IN1, IN2) | 19 | |
| Pulsed CMOS Input High Voltage | VIH | 0.8 | V | Pulsed CMOS input buffer, DC coupled (IN0, IN1, IN2) | 19 | ||
| Minimum Pulse Width | PW | 1.6 | ns | Pulse input | 19 | ||
| Minimum Pulse Width | TPW | 100 | ns | RSTb only | 20 | ||
| Input Frequency Range (REFCLK, XA/XB) | fIN | 10 | 200 | MHz | Full operating range; jitter performance may be reduced | 19 | |
| Input Frequency Range (REFCLK, XA/XB) | fIN | 48 | 54 | MHz | Range for best jitter | 19 | |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | 400 | 600 | ps | VDDO = 3.3 V | 23 | |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | 450 | 600 | ps | VDDO = 2.5 V | 23 | |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | 550 | 750 | ps | VDDO = 1.8 V | 23 | |
| Crystal Frequency Range | fXTAL | 24.97 | 54.06 | MHz | Full operating range; jitter performance may be reduced | 30 | |
| Crystal Frequency Range | fXTAL | 48 | 54 | MHz | Range for best jitter | 30 | |
| Crystal Drive Level | dL | 200 | μW | 30 | |||
| PLL Lock Time | tACQ | 15 | 150 | ms | fIN = 19.44 MHz | 24 | |
| Initial Start-Up Time | tSTART | 30 | 45 | ms | Input frequency >48 MHz | 24 | |
| POR to Serial Interface Ready | tRDY | 15 | ms | 24 | |||
| Jitter Generation (integer mode, 12 kHz to 20 MHz) | JGEN | 90 | 140 | fs rms | Locked to external XTAL, XTAL frequency 48 MHz, integer mode, 12 kHz to 20 MHz | 25 | |
| Jitter Generation (fractional/DCO mode, 12 kHz to 20 MHz) | JGEN | 115 | 170 | fs rms | Locked to external XTAL, XTAL frequency 48 MHz, fractional/DCO mode, 12 kHz to 20 MHz | 25 | |
| Storage Temperature Range | TSTG | -55 | 150 | °C | 31 | ||
| DC Supply Voltage VDD | VDD | -0.5 | 3.8 | V | 31 | ||
| DC Supply Voltage VDDA | VDDA | -0.5 | 3.8 | V | 31 | ||
| DC Supply Voltage VDDO | VDDO | -0.5 | 3.8 | V | 31 | ||
| Input Voltage Range IN0-IN2, FB_IN | VI1 | -1 | 3.8 | V | 31 | ||
| Input Voltage Range control pins | VI2 | -0.5 | 3.8 | V | IN_SEL[1:0], RSTb, OEb, SYNCb, I2C_SEL, SDI, SCLK, A0/CSb, A1, SDA/SDIO, FINC/FDEC | 31 | |
| Input Voltage Range XA/XB | VI3 | -0.5 | 2.7 | V | 31 | ||
| ESD Tolerance HBM | 2 | kV | HBM 100 pF, 1.5 kΩ | 31 | |||
| Maximum Junction Temperature in Operation | TJCT | 125 | °C | 31 | |||
| Soldering Temperature (Pb-free profile) | TPEAK | 260 | °C | 31 | |||
| Thermal Resistance Junction to Ambient | ϴJA | 22.3 | °C/W | Still air | 30 | ||
| Thermal Resistance Junction to Ambient | ϴJA | 19.4 | °C/W | Air flow 1 m/s | 30 | ||
| Thermal Resistance Junction to Ambient | ϴJA | 18.4 | °C/W | Air flow 2 m/s | 30 | ||
| Thermal Resistance Junction to Case | ϴJC | 10.9 | °C/W | 30 | |||
| Thermal Resistance Junction to Board | ϴJB | 9.3 | °C/W | 30 | |||
| Thermal Resistance Junction to Board | ΨJB | 9.2 | °C/W | 30 | |||
| Thermal Resistance Junction to Top Center | ΨJT | 0.23 | °C/W | 30 | |||
| Input Capacitance (differential/single-ended clock inputs) | CIN | 2.4 | pF | 19 | |||
| Input Resistance Differential | RIN_DIFF | 16 | kΩ | 19 | |||
| Input Resistance Single-Ended | RIN_SE | 8 | kΩ | 19 | |||
| Control Input Capacitance | CIN | 2 | pF | Si5340 control input pins | 20 | ||
| Control Input Resistance | RIN | 20 | kΩ | Si5340 control input pins | 20 | ||
| Load Capacitance | CL | 8 | pF | 30 | |||
| PLL Loop Bandwidth | fBW | 1 | MHz | 24 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. | 42 |
CAD (KiCad official)
- Symbol:
SI5340A-D-GM - Footprint:
Package_DFN_QFN:QFN-44-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: QFN-44-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
si5340a-d-gm-etched.step/si5340a-d-gm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si5340a-d-gm.step/si5340a-d-gm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (49 pp, sha256
0b243d92e50b9eae, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SI5340A-D-GM
**SILICON LABS** · Clock Generators / Frequency Synthesizers / PLL · QFN-44-EP(7x7)
SI5340A-D-GM from SILICON LABS, in a QFN-44-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | input | Clock input IN1 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 2 | IN1b | input | Complementary clock input IN1b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 3 | IN_SEL0 | input | Input reference select bit 0 chooses the active clock input in manual pin-controlled mode and is internally pulled up with a ~20 kΩ resistor. |
| 4 | X1 | input | XTAL shield pin must be connected directly to the XTAL ground pins, must not be connected to the PCB ground plane, and should be left disconnected when XA/XB is driven by an external reference clock. |
| 5 | XA | input | Crystal and external clock input used to connect an external crystal or external clock, selected when IN_SEL[1:0] = 11b. |
| 6 | XB | input | Crystal and external clock input used with XA to connect an external crystal or external clock. |
| 7 | X2 | input | XTAL shield pin must be connected directly to the XTAL ground pins, must not be connected to the PCB ground plane, and should be left disconnected when XA/XB is driven by an external reference clock. |
| 8 | VDDA | power_in | Core supply pin requires a 3.3 V power source and a 1.0 µF bypass capacitor is recommended. |
| 9 | VDDA | power_in | Core supply pin requires a 3.3 V power source and a 1.0 µF bypass capacitor is recommended. |
| 10 | IN2 | input | Clock input IN2 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 11 | IN2b | input | Complementary clock input IN2b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 12 | OEb | input | Output enable input disables all outputs when held high and is internally pulled low, so it can be left unconnected when not in use. |
| 13 | SDA/SDIO | bidirectional | Bidirectional serial data pin (SDA in I2C mode, SDIO in 3-wire SPI) that requires an external pull-up of at least 1 kΩ in I2C mode and no pull-up in SPI mode. |
| 14 | SCLK | input | Serial clock input for I2C and SPI modes that requires an external pull-up of at least 1 kΩ in I2C mode and is internally pulled up with ~20 kΩ. |
| 15 | A1/SDO | bidirectional | Address select 1 in I2C mode with no internal pull resistor, and serial data output (SDO) in 4-wire SPI mode. |
| 16 | A0/CSb | input | Address select 0 in I2C mode and active-low chip select input in SPI mode, internally pulled up with ~20 kΩ. |
| 17 | RSTb | input | Active-low device reset input that performs power-on reset and forces registers to default values, with clock outputs disabled during reset; internally pulled up with ~20 kΩ. |
| 18 | VDDO0 | power_in | Output clock supply voltage for OUT0 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 19 | OUT0b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 20 | OUT0 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 21 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 22 | NC | unconnected | No connect pin that is not connected to the die and must be left disconnected. |
| 23 | VDDO1 | power_in | Output clock supply voltage for OUT1 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 24 | OUT1b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 25 | OUT1 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 26 | VDDS | power_in | Status output voltage supply that sets the VOL/VOH levels on LOLb and LOS_XAXBb and needs a 0.1 µF to 1.0 µF bypass capacitor. |
| 27 | LOLb | output | Loss of lock output that is high when the DSPLL is locked and low when out-of-lock, requiring no external pull-up or pull-down. |
| 28 | LOS_XAXBb | output | Loss of signal output that indicates a loss of signal at the XA/XB pins. |
| 29 | VDDO2 | power_in | Output clock supply voltage for OUT2 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 30 | OUT2b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 31 | OUT2 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 32 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 33 | INTRb | output | Interrupt output asserted low when a change in device status occurs; it is push-pull and should be left unconnected when not in use. |
| 34 | VDDO3 | power_in | Output clock supply voltage for OUT3 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused. |
| 35 | OUT3b | output | Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 36 | OUT3 | output | Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected. |
| 37 | IN_SEL1 | input | Input reference select bit 1 chooses the active clock input in manual pin-controlled mode and is internally pulled up with a ~20 kΩ resistor. |
| 38 | I2C_SEL | input | Serial interface select that chooses I2C when high (1) and SPI when low (0), internally pulled up with ~20 kΩ. |
| 39 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 40 | VDD | power_in | Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended. |
| 41 | FB_IN | input | External feedback input used with FB_INb for the optional zero delay mode and which can be left floating if unused and powered down. |
| 42 | FB_INb | input | Complementary external feedback input used with FB_IN for the optional zero delay mode and which can be left floating if unused and powered down. |
| 43 | IN0 | input | Clock input IN0 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 44 | IN0b | input | Complementary clock input IN0b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance. |
| 45 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-44-EP(7x7) |
| Category | RTC/Clock Chip |
| Pins | 45 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient Temperature | TA | -40 | 25 | 85 | °C | | 17 |
| Junction Temperature | TJMAX | | | 125 | °C | | 17 |
| Core Supply Voltage | VDD | 1.71 | 1.8 | 1.89 | V | | 17 |
| Core Supply Voltage 3.3 V | VDDA | 3.14 | 3.3 | 3.47 | V | | 17 |
| Output Driver Supply Voltage | VDDO | 3.14 | 3.3 | 3.47 | V | | 17 |
| Output Driver Supply Voltage | VDDO | 2.37 | 2.5 | 2.62 | V | | 17 |
| Output Driver Supply Voltage | VDDO | 1.71 | 1.8 | 1.89 | V | | 17 |
| Core Supply Current | IDD | | 115 | 230 | mA | Si5340/41 | 18 |
| Core Supply Current (analog) | IDDA | | 120 | 130 | mA | Si5340/41 | 18 |
| Total Power Dissipation | Pd | | 680 | 875 | mW | Si5340 | 18 |
| Input Frequency Range | fIN | 10 | | 750 | MHz | Differential | 19 |
| Input Frequency Range | fIN | 10 | | 250 | MHz | All single-ended signals (including LVCMOS) | 19 |
| Input Slew Rate | SR | 400 | | | V/μs | | 19 |
| Pulsed CMOS Input Low Voltage | VIL | -0.2 | | 0.4 | V | Pulsed CMOS input buffer, DC coupled (IN0, IN1, IN2) | 19 |
| Pulsed CMOS Input High Voltage | VIH | 0.8 | | | V | Pulsed CMOS input buffer, DC coupled (IN0, IN1, IN2) | 19 |
| Minimum Pulse Width | PW | 1.6 | | | ns | Pulse input | 19 |
| Minimum Pulse Width | TPW | 100 | | | ns | RSTb only | 20 |
| Input Frequency Range (REFCLK, XA/XB) | fIN | 10 | | 200 | MHz | Full operating range; jitter performance may be reduced | 19 |
| Input Frequency Range (REFCLK, XA/XB) | fIN | 48 | | 54 | MHz | Range for best jitter | 19 |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | | 400 | 600 | ps | VDDO = 3.3 V | 23 |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | | 450 | 600 | ps | VDDO = 2.5 V | 23 |
| LVCMOS Rise and Fall Time (20% to 80%) | tr/tf | | 550 | 750 | ps | VDDO = 1.8 V | 23 |
| Crystal Frequency Range | fXTAL | 24.97 | | 54.06 | MHz | Full operating range; jitter performance may be reduced | 30 |
| Crystal Frequency Range | fXTAL | 48 | | 54 | MHz | Range for best jitter | 30 |
| Crystal Drive Level | dL | | | 200 | μW | | 30 |
| PLL Lock Time | tACQ | 15 | | 150 | ms | fIN = 19.44 MHz | 24 |
| Initial Start-Up Time | tSTART | | 30 | 45 | ms | Input frequency >48 MHz | 24 |
| POR to Serial Interface Ready | tRDY | | | 15 | ms | | 24 |
| Jitter Generation (integer mode, 12 kHz to 20 MHz) | JGEN | | 90 | 140 | fs rms | Locked to external XTAL, XTAL frequency 48 MHz, integer mode, 12 kHz to 20 MHz | 25 |
| Jitter Generation (fractional/DCO mode, 12 kHz to 20 MHz) | JGEN | | 115 | 170 | fs rms | Locked to external XTAL, XTAL frequency 48 MHz, fractional/DCO mode, 12 kHz to 20 MHz | 25 |
| Storage Temperature Range | TSTG | -55 | | 150 | °C | | 31 |
| DC Supply Voltage VDD | VDD | -0.5 | | 3.8 | V | | 31 |
| DC Supply Voltage VDDA | VDDA | -0.5 | | 3.8 | V | | 31 |
| DC Supply Voltage VDDO | VDDO | -0.5 | | 3.8 | V | | 31 |
| Input Voltage Range IN0-IN2, FB_IN | VI1 | -1 | | 3.8 | V | | 31 |
| Input Voltage Range control pins | VI2 | -0.5 | | 3.8 | V | IN_SEL[1:0], RSTb, OEb, SYNCb, I2C_SEL, SDI, SCLK, A0/CSb, A1, SDA/SDIO, FINC/FDEC | 31 |
| Input Voltage Range XA/XB | VI3 | -0.5 | | 2.7 | V | | 31 |
| ESD Tolerance HBM | | | | 2 | kV | HBM 100 pF, 1.5 kΩ | 31 |
| Maximum Junction Temperature in Operation | TJCT | | | 125 | °C | | 31 |
| Soldering Temperature (Pb-free profile) | TPEAK | | | 260 | °C | | 31 |
| Thermal Resistance Junction to Ambient | ϴJA | | 22.3 | | °C/W | Still air | 30 |
| Thermal Resistance Junction to Ambient | ϴJA | | 19.4 | | °C/W | Air flow 1 m/s | 30 |
| Thermal Resistance Junction to Ambient | ϴJA | | 18.4 | | °C/W | Air flow 2 m/s | 30 |
| Thermal Resistance Junction to Case | ϴJC | | 10.9 | | °C/W | | 30 |
| Thermal Resistance Junction to Board | ϴJB | | 9.3 | | °C/W | | 30 |
| Thermal Resistance Junction to Board | ΨJB | | 9.2 | | °C/W | | 30 |
| Thermal Resistance Junction to Top Center | ΨJT | | 0.23 | | °C/W | | 30 |
| Input Capacitance (differential/single-ended clock inputs) | CIN | | 2.4 | | pF | | 19 |
| Input Resistance Differential | RIN_DIFF | | 16 | | kΩ | | 19 |
| Input Resistance Single-Ended | RIN_SE | | 8 | | kΩ | | 19 |
| Control Input Capacitance | CIN | | 2 | | pF | Si5340 control input pins | 20 |
| Control Input Resistance | RIN | | 20 | | kΩ | Si5340 control input pins | 20 |
| Load Capacitance | CL | | 8 | | pF | | 30 |
| PLL Loop Bandwidth | fBW | | 1 | | MHz | | 24 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. | 42 |
## CAD (KiCad official)
- Symbol: `SI5340A-D-GM`
- Footprint: `Package_DFN_QFN:QFN-44-1EP_7x7mm_P0.5mm_EP5.15x5.15mm`
- 3D model: QFN-44-EP(7x7) (KiCad packages3D, STEP)
- 3D model files: `si5340a-d-gm-etched.step` / `si5340a-d-gm-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `si5340a-d-gm.step` / `si5340a-d-gm.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [SILICON LABS datasheet](docs/si5340a-d-gm-datasheet.pdf) (49 pp, sha256 `0b243d92e50b9eae`, retrieved 2026-11-02, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/si5340a-d-gm-datasheet.pdf)