Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SI5340A-D-GM

SILICON LABS · Clock Generators / Frequency Synthesizers / PLL · QFN-44-EP(7x7)

SI5340A-D-GM from SILICON LABS, in a QFN-44-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN1 input Clock input IN1 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance.
2 IN1b input Complementary clock input IN1b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance.
3 IN_SEL0 input Input reference select bit 0 chooses the active clock input in manual pin-controlled mode and is internally pulled up with a ~20 kΩ resistor.
4 X1 input XTAL shield pin must be connected directly to the XTAL ground pins, must not be connected to the PCB ground plane, and should be left disconnected when XA/XB is driven by an external reference clock.
5 XA input Crystal and external clock input used to connect an external crystal or external clock, selected when IN_SEL[1:0] = 11b.
6 XB input Crystal and external clock input used with XA to connect an external crystal or external clock.
7 X2 input XTAL shield pin must be connected directly to the XTAL ground pins, must not be connected to the PCB ground plane, and should be left disconnected when XA/XB is driven by an external reference clock.
8 VDDA power_in Core supply pin requires a 3.3 V power source and a 1.0 µF bypass capacitor is recommended.
9 VDDA power_in Core supply pin requires a 3.3 V power source and a 1.0 µF bypass capacitor is recommended.
10 IN2 input Clock input IN2 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance.
11 IN2b input Complementary clock input IN2b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance.
12 OEb input Output enable input disables all outputs when held high and is internally pulled low, so it can be left unconnected when not in use.
13 SDA/SDIO bidirectional Bidirectional serial data pin (SDA in I2C mode, SDIO in 3-wire SPI) that requires an external pull-up of at least 1 kΩ in I2C mode and no pull-up in SPI mode.
14 SCLK input Serial clock input for I2C and SPI modes that requires an external pull-up of at least 1 kΩ in I2C mode and is internally pulled up with ~20 kΩ.
15 A1/SDO bidirectional Address select 1 in I2C mode with no internal pull resistor, and serial data output (SDO) in 4-wire SPI mode.
16 A0/CSb input Address select 0 in I2C mode and active-low chip select input in SPI mode, internally pulled up with ~20 kΩ.
17 RSTb input Active-low device reset input that performs power-on reset and forces registers to default values, with clock outputs disabled during reset; internally pulled up with ~20 kΩ.
18 VDDO0 power_in Output clock supply voltage for OUT0 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused.
19 OUT0b output Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
20 OUT0 output Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
21 VDD power_in Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended.
22 NC unconnected No connect pin that is not connected to the die and must be left disconnected.
23 VDDO1 power_in Output clock supply voltage for OUT1 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused.
24 OUT1b output Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
25 OUT1 output Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
26 VDDS power_in Status output voltage supply that sets the VOL/VOH levels on LOLb and LOS_XAXBb and needs a 0.1 µF to 1.0 µF bypass capacitor.
27 LOLb output Loss of lock output that is high when the DSPLL is locked and low when out-of-lock, requiring no external pull-up or pull-down.
28 LOS_XAXBb output Loss of signal output that indicates a loss of signal at the XA/XB pins.
29 VDDO2 power_in Output clock supply voltage for OUT2 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused.
30 OUT2b output Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
31 OUT2 output Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
32 VDD power_in Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended.
33 INTRb output Interrupt output asserted low when a change in device status occurs; it is push-pull and should be left unconnected when not in use.
34 VDDO3 power_in Output clock supply voltage for OUT3 that supports 3.3 V, 2.5 V or 1.8 V and should be left unconnected if the output driver is unused.
35 OUT3b output Complementary output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
36 OUT3 output Output clock with programmable signal amplitude when configured as a differential output; unused outputs should be left unconnected.
37 IN_SEL1 input Input reference select bit 1 chooses the active clock input in manual pin-controlled mode and is internally pulled up with a ~20 kΩ resistor.
38 I2C_SEL input Serial interface select that chooses I2C when high (1) and SPI when low (0), internally pulled up with ~20 kΩ.
39 VDD power_in Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended.
40 VDD power_in Core supply voltage of 1.8 V with a 1.0 µF bypass capacitor recommended.
41 FB_IN input External feedback input used with FB_INb for the optional zero delay mode and which can be left floating if unused and powered down.
42 FB_INb input Complementary external feedback input used with FB_IN for the optional zero delay mode and which can be left floating if unused and powered down.
43 IN0 input Clock input IN0 accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance.
44 IN0b input Complementary clock input IN0b accepts differential or single-ended clock signals and must be terminated externally because it is high-impedance.
45 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer SILICON LABS
Package QFN-44-EP(7x7)
Category RTC/Clock Chip
Pins 45

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient Temperature TA -40 25 85 °C 17
Junction Temperature TJMAX 125 °C 17
Core Supply Voltage VDD 1.71 1.8 1.89 V 17
Core Supply Voltage 3.3 V VDDA 3.14 3.3 3.47 V 17
Output Driver Supply Voltage VDDO 3.14 3.3 3.47 V 17
Output Driver Supply Voltage VDDO 2.37 2.5 2.62 V 17
Output Driver Supply Voltage VDDO 1.71 1.8 1.89 V 17
Core Supply Current IDD 115 230 mA Si5340/41 18
Core Supply Current (analog) IDDA 120 130 mA Si5340/41 18
Total Power Dissipation Pd 680 875 mW Si5340 18
Input Frequency Range fIN 10 750 MHz Differential 19
Input Frequency Range fIN 10 250 MHz All single-ended signals (including LVCMOS) 19
Input Slew Rate SR 400 V/μs 19
Pulsed CMOS Input Low Voltage VIL -0.2 0.4 V Pulsed CMOS input buffer, DC coupled (IN0, IN1, IN2) 19
Pulsed CMOS Input High Voltage VIH 0.8 V Pulsed CMOS input buffer, DC coupled (IN0, IN1, IN2) 19
Minimum Pulse Width PW 1.6 ns Pulse input 19
Minimum Pulse Width TPW 100 ns RSTb only 20
Input Frequency Range (REFCLK, XA/XB) fIN 10 200 MHz Full operating range; jitter performance may be reduced 19
Input Frequency Range (REFCLK, XA/XB) fIN 48 54 MHz Range for best jitter 19
LVCMOS Rise and Fall Time (20% to 80%) tr/tf 400 600 ps VDDO = 3.3 V 23
LVCMOS Rise and Fall Time (20% to 80%) tr/tf 450 600 ps VDDO = 2.5 V 23
LVCMOS Rise and Fall Time (20% to 80%) tr/tf 550 750 ps VDDO = 1.8 V 23
Crystal Frequency Range fXTAL 24.97 54.06 MHz Full operating range; jitter performance may be reduced 30
Crystal Frequency Range fXTAL 48 54 MHz Range for best jitter 30
Crystal Drive Level dL 200 μW 30
PLL Lock Time tACQ 15 150 ms fIN = 19.44 MHz 24
Initial Start-Up Time tSTART 30 45 ms Input frequency >48 MHz 24
POR to Serial Interface Ready tRDY 15 ms 24
Jitter Generation (integer mode, 12 kHz to 20 MHz) JGEN 90 140 fs rms Locked to external XTAL, XTAL frequency 48 MHz, integer mode, 12 kHz to 20 MHz 25
Jitter Generation (fractional/DCO mode, 12 kHz to 20 MHz) JGEN 115 170 fs rms Locked to external XTAL, XTAL frequency 48 MHz, fractional/DCO mode, 12 kHz to 20 MHz 25
Storage Temperature Range TSTG -55 150 °C 31
DC Supply Voltage VDD VDD -0.5 3.8 V 31
DC Supply Voltage VDDA VDDA -0.5 3.8 V 31
DC Supply Voltage VDDO VDDO -0.5 3.8 V 31
Input Voltage Range IN0-IN2, FB_IN VI1 -1 3.8 V 31
Input Voltage Range control pins VI2 -0.5 3.8 V IN_SEL[1:0], RSTb, OEb, SYNCb, I2C_SEL, SDI, SCLK, A0/CSb, A1, SDA/SDIO, FINC/FDEC 31
Input Voltage Range XA/XB VI3 -0.5 2.7 V 31
ESD Tolerance HBM 2 kV HBM 100 pF, 1.5 kΩ 31
Maximum Junction Temperature in Operation TJCT 125 °C 31
Soldering Temperature (Pb-free profile) TPEAK 260 °C 31
Thermal Resistance Junction to Ambient ϴJA 22.3 °C/W Still air 30
Thermal Resistance Junction to Ambient ϴJA 19.4 °C/W Air flow 1 m/s 30
Thermal Resistance Junction to Ambient ϴJA 18.4 °C/W Air flow 2 m/s 30
Thermal Resistance Junction to Case ϴJC 10.9 °C/W 30
Thermal Resistance Junction to Board ϴJB 9.3 °C/W 30
Thermal Resistance Junction to Board ΨJB 9.2 °C/W 30
Thermal Resistance Junction to Top Center ΨJT 0.23 °C/W 30
Input Capacitance (differential/single-ended clock inputs) CIN 2.4 pF 19
Input Resistance Differential RIN_DIFF 16 kΩ 19
Input Resistance Single-Ended RIN_SE 8 kΩ 19
Control Input Capacitance CIN 2 pF Si5340 control input pins 20
Control Input Resistance RIN 20 kΩ Si5340 control input pins 20
Load Capacitance CL 8 pF 30
PLL Loop Bandwidth fBW 1 MHz 24

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing PC 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 42

CAD (KiCad official)

  • Symbol: SI5340A-D-GM
  • Footprint: Package_DFN_QFN:QFN-44-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: QFN-44-EP(7x7) (KiCad packages3D, STEP)
  • 3D model files: si5340a-d-gm-etched.step / si5340a-d-gm-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si5340a-d-gm.step / si5340a-d-gm.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SILICON LABS datasheet (49 pp, sha256 0b243d92e50b9eae, retrieved 2026-11-02, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF