main
History Download
Ray Publish 0.1.0 4cf84bc

SI5317C-C-GMR

SKYWORKS SILICON LABS · Clock Generators, PLLs, Frequency Synthesizers · QFN-36-EP(6x6)

SI5317C-C-GMR from SKYWORKS SILICON LABS, in a QFN-36-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RST input Active-low external reset that resets all internal logic and tristates the clock outputs during reset, with a minimum reset pulse width of 1 µs; it has a weak pull-up.
2 FRQTBL input Three-level input that selects the frequency table, defaults to M, and must be followed by a device reset after it is changed.
3 LOS output Active-high LVCMOS loss-of-signal indicator for CKIN (0 = CKIN present, 1 = LOS on CKIN) that stays asserted until CKIN is validated.
4 NC unconnected No connect; leave floating and make no external connections for normal operation.
5 VDD power_in Supply pin for 1.8, 2.5, or 3.3 V operation; the datasheet specifies a 0.1 µF bypass capacitor for this pin.
6 XA input Analog external crystal or reference clock input, used with a crystal or an external reference clock selected by the RATE[1:0] settings.
7 XB input Analog external crystal or reference clock connection; when the reference is driven single-ended, this pin is connected to ground through a capacitor.
8 GND power_in Ground pin that must be connected to system ground with minimal ground path impedance.
9 NC unconnected No connect; leave floating and make no external connections for normal operation.
10 VDD power_in Supply pin for 1.8, 2.5, or 3.3 V operation; the datasheet specifies a 0.1 µF bypass capacitor for this pin.
11 RATE0 input Three-level input that sets the external crystal or reference clock rate per Table 13, and a device reset is required after it is changed.
12 NC unconnected No connect; leave floating and make no external connections for normal operation.
13 NC unconnected No connect; leave floating and make no external connections for normal operation.
14 DBL2_BY input Three-level input controlling CKOUT2: L enables CKOUT2, M disables CKOUT2, and H enables PLL bypass mode with CKOUT2 enabled (bypass is not supported for CMOS outputs).
15 RATE1 input Three-level input that sets the external crystal or reference clock rate per Table 13, and a device reset is required after it is changed.
16 CKIN+ input Positive side of the differential clock input, which can also be driven single-ended, with an input frequency range of 1 to 711 MHz.
17 CKIN- input Negative side of the differential clock input, which can also be driven single-ended; AC coupling is recommended.
18 LOL output Active-high LVCMOS PLL loss-of-lock indicator (0 = PLL locked, 1 = PLL unlocked), also held active during internal calibration.
19 DEC input Edge-triggered skew decrement input that reduces the input-to-output skew by the step size defined in Table 8, and has a weak pull-down.
20 INC input Edge-triggered skew increment input that increases the input-to-output skew by the step size defined in Table 8, and has a weak pull-down.
21 NC unconnected No connect; leave floating and make no external connections for normal operation.
22 BWSEL0 input Three-level input that selects the DSPLL closed-loop bandwidth (60 Hz to 8.4 kHz), defaults to M, and requires a device reset after it is changed.
23 BWSEL1 input Three-level input that selects the DSPLL closed-loop bandwidth (60 Hz to 8.4 kHz), defaults to M, and requires a device reset after it is changed.
24 FRQSEL0 input Three-level input that, together with FRQSEL[3:1], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed.
25 FRQSEL1 input Three-level input that, together with FRQSEL[3:0], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed.
26 FRQSEL2 input Three-level input that, together with FRQSEL[3:0], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed.
27 FRQSEL3 input Three-level input that, together with FRQSEL[2:0], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed.
28 CKOUT1+ output Positive side of clock output 1 whose signal format (LVPECL, LVDS, CML, or CMOS) is set by the SFOUT pins; in CMOS format both pins drive in-phase signals.
29 CKOUT1- output Negative side of clock output 1 whose signal format is set by the SFOUT pins; in CMOS format it drives in phase with CKOUT1+ and must be shorted to it.
30 SFOUT1 input Three-level signal format select (with SFOUT0) for both CKOUT1 and CKOUT2, defaulting to M; LM disables both outputs and LH selects CMOS.
31 GND power_in Ground pin that must be connected to system ground with minimal ground path impedance.
32 VDD power_in Supply pin for 1.8, 2.5, or 3.3 V operation; the datasheet specifies a 0.1 µF bypass capacitor for this pin, with a 1.0 µF also placed close to the device.
33 SFOUT0 input Three-level signal format select (with SFOUT1) for both CKOUT1 and CKOUT2, defaulting to M; LM disables both outputs and LH selects CMOS.
34 CKOUT2- output Negative side of clock output 2 whose signal format is set by the SFOUT pins; in CMOS format it drives in phase with CKOUT2+ and must be shorted to it.
35 CKOUT2+ output Positive side of clock output 2 whose signal format is set by the SFOUT pins; in CMOS format both pins drive in-phase signals.
36 NC unconnected No connect; leave floating and make no external connections for normal operation.
37 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer SKYWORKS SILICON LABS
Package QFN-36-EP(6x6)
Category Clock/Timing
Pins 37

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Temperature Range TA -40 25 85 ºC 4
Supply Voltage, 3.3 V nominal VDD 2.97 3.3 3.63 V 3.3 V nominal 4
Supply Voltage, 2.5 V nominal VDD 2.25 2.5 2.75 V 2.5 V nominal 4
Supply Voltage, 1.8 V nominal VDD 1.71 1.8 1.89 V 1.8 V nominal 4
DC Supply Voltage VDD -0.5 3.8 V 13
LVCMOS Input Voltage (lower limit; upper limit printed as VDD + 0.3 V) VDIG -0.3 V 13
Operating Junction Temperature TJCT -55 150 C 13
Storage Temperature Range TSTG -55 150 C 13
ESD HBM Tolerance 2 kV 100 pF, 1.5 kΩ; all pins except CKIN+/CKIN- 13
Supply Current, LVPECL format, all CKOUTs enabled IDD 251 279 mA LVPECL Format, 622.08 MHz Out, All CKOUTs Enabled 4
Supply Current, LVPECL format, only 1 CKOUT enabled IDD 217 243 mA LVPECL Format, 622.08 MHz Out, Only 1 CKOUT Enabled 4
Supply Current, CMOS format, all CKOUTs enabled IDD 204 234 mA CMOS Format, 19.44 MHz Out, All CKOUTs Enabled 4
Supply Current, CMOS format, only CKOUT1 enabled IDD 194 220 mA CMOS Format, 19.44 MHz Out, Only CKOUT1 Enabled 4
CKIN Input Common Mode Voltage (Input Threshold Voltage) VICM 0.9 1.4 V 1.8 V ± 5% 4
CKIN Input Common Mode Voltage (Input Threshold Voltage) VICM 1 1.7 V 2.5 V ± 10% 4
CKIN Input Common Mode Voltage (Input Threshold Voltage) VICM 1.1 1.95 V 3.3 V ± 10% 4
Input Voltage Level Limits (CKIN) CKNVIN 0 V No overshoot or undershoot 4
Single-ended Input Voltage Swing VISE 0.2 VPP fCKIN < 212.5 MHz 4
Single-ended Input Voltage Swing VISE 0.25 VPP fCKIN > 212.5 MHz 4
Differential Input Voltage Swing VID 0.2 VPP fCKIN < 212.5 MHz 5
Differential Input Voltage Swing VID 0.25 VPP fCKIN > 212.5 MHz 5
Differential Output Swing (LVPECL) VOD 1.1 1.9 VPP LVPECL 100 Ω load line-to-line 5
Single-ended Output Swing (LVPECL) VSE 0.5 0.93 VPP LVPECL 100 Ω load line-to-line 5
Differential Output Voltage (CML) CKOVD 350 425 500 mVPP CML 100 Ω load line-to-line 5
Differential Output Voltage (LVDS) CKOVD 500 700 900 mVPP LVDS 100 Ω load line-to-line 5
Differential Output Voltage (Low swing LVDS) CKOVD 350 425 500 mVPP Low swing LVDS 100 Ω load line-to-line 5
Common Mode Output Voltage (LVDS) CKOVCM 1.125 1.2 1.275 V LVDS 100 Ω load line-to-line 5
Output Voltage Low (CMOS) CKOVOLLH 0.4 V CMOS 5
Input Voltage Low (2-level LVCMOS) VIL 0.5 V VDD = 1.71 V 5
Input Voltage Low (2-level LVCMOS) VIL 0.7 V VDD = 2.25 V 5
Input Voltage Low (2-level LVCMOS) VIL 0.8 V VDD = 2.97 V 5
Input Voltage High (2-level LVCMOS) VIH 1.4 V VDD = 1.89 V 6
Input Voltage High (2-level LVCMOS) VIH 1.8 V VDD = 2.25 V 6
Input Voltage High (2-level LVCMOS) VIH 2.5 V VDD = 3.63 V 6
Input Low Current IIL 50 μA 6
Input High Current IIH 50 μA 6
Input Low Current (3-level input pins) IILL -20 μA 6
Input Mid Current (3-level input pins) IIMM -2 2 μA 6
Input High Current (3-level input pins) IIHH 20 μA 6
Output Voltage Low (LVCMOS) VOL 0.4 V IO = 2 mA, VDD = 1.62 V 7
Input Voltage Level Limits (single-ended XA) XAVIN 0 1.2 V 7
Input Voltage Swing (single-ended XA) XAVPP 0.5 1.2 VPP 7
Differential Input Voltage Level Limits (XA/XB) XA/XBVIN 0 1.2 V 7
Input Voltage Swing (XA/XB differential) XAVPP/XBVPP 0.5 2.4 VPP 7
Input Frequency CKNF 1 711 MHz 11
Input Duty Cycle CKNDC 40 60 % Whichever is smaller 11
Minimum Pulse Width (CKIN) 2 ns Whichever is smaller 11
Input Rise/Fall Time CKNTRF 11 ns 20-80%, See Figure 2 11
Output Frequency CKOF 1 711 MHz Output not configured for CMOS or disable 11
Maximum Output Frequency in CMOS Format CKOFMC 1 212.5 MHz 11
Single-ended Output Rise/Fall (20-80%), CMOS CKOTRF 8 ns CMOS Output, VDD = 1.62 V, Cload = 5 pF 11
Single-ended Output Rise/Fall (20-80%), CMOS CKOTRF 2 ns CMOS Output, VDD = 2.97 V, Cload = 5 pF 11
Differential Output Rise/Fall Time CKOTRF 230 350 ps 20 to 80 %, fOUT = 622.08 MHz 11
Output Duty Cycle Differential Uncertainty CKODC -40 40 ps 100 Ω Load Line to Line; Measured at 50% Point (not for CMOS) 11
Lock Time tLOCKHW 1.2 sec Whenever RST, FRQTBL, RATE, BWSEL, or FRQSEL are changed, with valid CKIN to LOL; BW = 100 Hz 12
Output clock frequency range (Si5317C variant) 1 200 MHz Ordering Guide, Si5317C-C-GM output clock freq range 40
Jitter Generation (12 kHz-20 MHz) JGEN 0.31 0.41 ps rms fIN = fOUT = 622.08 MHz, LVPECL output format, BW = 120 Hz, 12 kHz-20 MHz 12
Thermal Resistance Junction to Ambient JA 32 ºC/W Still Air 13
Thermal Resistance Junction to Case JC 14 ºC/W 13

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing PC 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body 41

CAD (KiCad official)

  • Symbol: SI5317C-C-GMR
  • Footprint: Package_DFN_QFN:QFN-36-1EP_6x6mm_P0.5mm_EP3.7x3.7mm
  • 3D model: QFN-36-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: si5317c-c-gmr-etched.step / si5317c-c-gmr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si5317c-c-gmr.step / si5317c-c-gmr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SKYWORKS SILICON LABS datasheet (46 pp, sha256 bf5e9ec3b0439041, retrieved 2026-11-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF