3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSI5317C-C-GMR
SKYWORKS SILICON LABS · Clock Generators, PLLs, Frequency Synthesizers · QFN-36-EP(6x6)
SI5317C-C-GMR from SKYWORKS SILICON LABS, in a QFN-36-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RST | input | Active-low external reset that resets all internal logic and tristates the clock outputs during reset, with a minimum reset pulse width of 1 µs; it has a weak pull-up. |
| 2 | FRQTBL | input | Three-level input that selects the frequency table, defaults to M, and must be followed by a device reset after it is changed. |
| 3 | LOS | output | Active-high LVCMOS loss-of-signal indicator for CKIN (0 = CKIN present, 1 = LOS on CKIN) that stays asserted until CKIN is validated. |
| 4 | NC | unconnected | No connect; leave floating and make no external connections for normal operation. |
| 5 | VDD | power_in | Supply pin for 1.8, 2.5, or 3.3 V operation; the datasheet specifies a 0.1 µF bypass capacitor for this pin. |
| 6 | XA | input | Analog external crystal or reference clock input, used with a crystal or an external reference clock selected by the RATE[1:0] settings. |
| 7 | XB | input | Analog external crystal or reference clock connection; when the reference is driven single-ended, this pin is connected to ground through a capacitor. |
| 8 | GND | power_in | Ground pin that must be connected to system ground with minimal ground path impedance. |
| 9 | NC | unconnected | No connect; leave floating and make no external connections for normal operation. |
| 10 | VDD | power_in | Supply pin for 1.8, 2.5, or 3.3 V operation; the datasheet specifies a 0.1 µF bypass capacitor for this pin. |
| 11 | RATE0 | input | Three-level input that sets the external crystal or reference clock rate per Table 13, and a device reset is required after it is changed. |
| 12 | NC | unconnected | No connect; leave floating and make no external connections for normal operation. |
| 13 | NC | unconnected | No connect; leave floating and make no external connections for normal operation. |
| 14 | DBL2_BY | input | Three-level input controlling CKOUT2: L enables CKOUT2, M disables CKOUT2, and H enables PLL bypass mode with CKOUT2 enabled (bypass is not supported for CMOS outputs). |
| 15 | RATE1 | input | Three-level input that sets the external crystal or reference clock rate per Table 13, and a device reset is required after it is changed. |
| 16 | CKIN+ | input | Positive side of the differential clock input, which can also be driven single-ended, with an input frequency range of 1 to 711 MHz. |
| 17 | CKIN- | input | Negative side of the differential clock input, which can also be driven single-ended; AC coupling is recommended. |
| 18 | LOL | output | Active-high LVCMOS PLL loss-of-lock indicator (0 = PLL locked, 1 = PLL unlocked), also held active during internal calibration. |
| 19 | DEC | input | Edge-triggered skew decrement input that reduces the input-to-output skew by the step size defined in Table 8, and has a weak pull-down. |
| 20 | INC | input | Edge-triggered skew increment input that increases the input-to-output skew by the step size defined in Table 8, and has a weak pull-down. |
| 21 | NC | unconnected | No connect; leave floating and make no external connections for normal operation. |
| 22 | BWSEL0 | input | Three-level input that selects the DSPLL closed-loop bandwidth (60 Hz to 8.4 kHz), defaults to M, and requires a device reset after it is changed. |
| 23 | BWSEL1 | input | Three-level input that selects the DSPLL closed-loop bandwidth (60 Hz to 8.4 kHz), defaults to M, and requires a device reset after it is changed. |
| 24 | FRQSEL0 | input | Three-level input that, together with FRQSEL[3:1], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed. |
| 25 | FRQSEL1 | input | Three-level input that, together with FRQSEL[3:0], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed. |
| 26 | FRQSEL2 | input | Three-level input that, together with FRQSEL[3:0], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed. |
| 27 | FRQSEL3 | input | Three-level input that, together with FRQSEL[2:0], selects the input clock and clock range, defaults to M, and requires a device reset after it is changed. |
| 28 | CKOUT1+ | output | Positive side of clock output 1 whose signal format (LVPECL, LVDS, CML, or CMOS) is set by the SFOUT pins; in CMOS format both pins drive in-phase signals. |
| 29 | CKOUT1- | output | Negative side of clock output 1 whose signal format is set by the SFOUT pins; in CMOS format it drives in phase with CKOUT1+ and must be shorted to it. |
| 30 | SFOUT1 | input | Three-level signal format select (with SFOUT0) for both CKOUT1 and CKOUT2, defaulting to M; LM disables both outputs and LH selects CMOS. |
| 31 | GND | power_in | Ground pin that must be connected to system ground with minimal ground path impedance. |
| 32 | VDD | power_in | Supply pin for 1.8, 2.5, or 3.3 V operation; the datasheet specifies a 0.1 µF bypass capacitor for this pin, with a 1.0 µF also placed close to the device. |
| 33 | SFOUT0 | input | Three-level signal format select (with SFOUT1) for both CKOUT1 and CKOUT2, defaulting to M; LM disables both outputs and LH selects CMOS. |
| 34 | CKOUT2- | output | Negative side of clock output 2 whose signal format is set by the SFOUT pins; in CMOS format it drives in phase with CKOUT2+ and must be shorted to it. |
| 35 | CKOUT2+ | output | Positive side of clock output 2 whose signal format is set by the SFOUT pins; in CMOS format both pins drive in-phase signals. |
| 36 | NC | unconnected | No connect; leave floating and make no external connections for normal operation. |
| 37 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SKYWORKS SILICON LABS |
| Package | QFN-36-EP(6x6) |
| Category | Clock/Timing |
| Pins | 37 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Temperature Range | TA | -40 | 25 | 85 | ºC | 4 | |
| Supply Voltage, 3.3 V nominal | VDD | 2.97 | 3.3 | 3.63 | V | 3.3 V nominal | 4 |
| Supply Voltage, 2.5 V nominal | VDD | 2.25 | 2.5 | 2.75 | V | 2.5 V nominal | 4 |
| Supply Voltage, 1.8 V nominal | VDD | 1.71 | 1.8 | 1.89 | V | 1.8 V nominal | 4 |
| DC Supply Voltage | VDD | -0.5 | 3.8 | V | 13 | ||
| LVCMOS Input Voltage (lower limit; upper limit printed as VDD + 0.3 V) | VDIG | -0.3 | V | 13 | |||
| Operating Junction Temperature | TJCT | -55 | 150 | C | 13 | ||
| Storage Temperature Range | TSTG | -55 | 150 | C | 13 | ||
| ESD HBM Tolerance | 2 | kV | 100 pF, 1.5 kΩ; all pins except CKIN+/CKIN- | 13 | |||
| Supply Current, LVPECL format, all CKOUTs enabled | IDD | 251 | 279 | mA | LVPECL Format, 622.08 MHz Out, All CKOUTs Enabled | 4 | |
| Supply Current, LVPECL format, only 1 CKOUT enabled | IDD | 217 | 243 | mA | LVPECL Format, 622.08 MHz Out, Only 1 CKOUT Enabled | 4 | |
| Supply Current, CMOS format, all CKOUTs enabled | IDD | 204 | 234 | mA | CMOS Format, 19.44 MHz Out, All CKOUTs Enabled | 4 | |
| Supply Current, CMOS format, only CKOUT1 enabled | IDD | 194 | 220 | mA | CMOS Format, 19.44 MHz Out, Only CKOUT1 Enabled | 4 | |
| CKIN Input Common Mode Voltage (Input Threshold Voltage) | VICM | 0.9 | 1.4 | V | 1.8 V ± 5% | 4 | |
| CKIN Input Common Mode Voltage (Input Threshold Voltage) | VICM | 1 | 1.7 | V | 2.5 V ± 10% | 4 | |
| CKIN Input Common Mode Voltage (Input Threshold Voltage) | VICM | 1.1 | 1.95 | V | 3.3 V ± 10% | 4 | |
| Input Voltage Level Limits (CKIN) | CKNVIN | 0 | V | No overshoot or undershoot | 4 | ||
| Single-ended Input Voltage Swing | VISE | 0.2 | VPP | fCKIN < 212.5 MHz | 4 | ||
| Single-ended Input Voltage Swing | VISE | 0.25 | VPP | fCKIN > 212.5 MHz | 4 | ||
| Differential Input Voltage Swing | VID | 0.2 | VPP | fCKIN < 212.5 MHz | 5 | ||
| Differential Input Voltage Swing | VID | 0.25 | VPP | fCKIN > 212.5 MHz | 5 | ||
| Differential Output Swing (LVPECL) | VOD | 1.1 | 1.9 | VPP | LVPECL 100 Ω load line-to-line | 5 | |
| Single-ended Output Swing (LVPECL) | VSE | 0.5 | 0.93 | VPP | LVPECL 100 Ω load line-to-line | 5 | |
| Differential Output Voltage (CML) | CKOVD | 350 | 425 | 500 | mVPP | CML 100 Ω load line-to-line | 5 |
| Differential Output Voltage (LVDS) | CKOVD | 500 | 700 | 900 | mVPP | LVDS 100 Ω load line-to-line | 5 |
| Differential Output Voltage (Low swing LVDS) | CKOVD | 350 | 425 | 500 | mVPP | Low swing LVDS 100 Ω load line-to-line | 5 |
| Common Mode Output Voltage (LVDS) | CKOVCM | 1.125 | 1.2 | 1.275 | V | LVDS 100 Ω load line-to-line | 5 |
| Output Voltage Low (CMOS) | CKOVOLLH | 0.4 | V | CMOS | 5 | ||
| Input Voltage Low (2-level LVCMOS) | VIL | 0.5 | V | VDD = 1.71 V | 5 | ||
| Input Voltage Low (2-level LVCMOS) | VIL | 0.7 | V | VDD = 2.25 V | 5 | ||
| Input Voltage Low (2-level LVCMOS) | VIL | 0.8 | V | VDD = 2.97 V | 5 | ||
| Input Voltage High (2-level LVCMOS) | VIH | 1.4 | V | VDD = 1.89 V | 6 | ||
| Input Voltage High (2-level LVCMOS) | VIH | 1.8 | V | VDD = 2.25 V | 6 | ||
| Input Voltage High (2-level LVCMOS) | VIH | 2.5 | V | VDD = 3.63 V | 6 | ||
| Input Low Current | IIL | 50 | μA | 6 | |||
| Input High Current | IIH | 50 | μA | 6 | |||
| Input Low Current (3-level input pins) | IILL | -20 | μA | 6 | |||
| Input Mid Current (3-level input pins) | IIMM | -2 | 2 | μA | 6 | ||
| Input High Current (3-level input pins) | IIHH | 20 | μA | 6 | |||
| Output Voltage Low (LVCMOS) | VOL | 0.4 | V | IO = 2 mA, VDD = 1.62 V | 7 | ||
| Input Voltage Level Limits (single-ended XA) | XAVIN | 0 | 1.2 | V | 7 | ||
| Input Voltage Swing (single-ended XA) | XAVPP | 0.5 | 1.2 | VPP | 7 | ||
| Differential Input Voltage Level Limits (XA/XB) | XA/XBVIN | 0 | 1.2 | V | 7 | ||
| Input Voltage Swing (XA/XB differential) | XAVPP/XBVPP | 0.5 | 2.4 | VPP | 7 | ||
| Input Frequency | CKNF | 1 | 711 | MHz | 11 | ||
| Input Duty Cycle | CKNDC | 40 | 60 | % | Whichever is smaller | 11 | |
| Minimum Pulse Width (CKIN) | 2 | ns | Whichever is smaller | 11 | |||
| Input Rise/Fall Time | CKNTRF | 11 | ns | 20-80%, See Figure 2 | 11 | ||
| Output Frequency | CKOF | 1 | 711 | MHz | Output not configured for CMOS or disable | 11 | |
| Maximum Output Frequency in CMOS Format | CKOFMC | 1 | 212.5 | MHz | 11 | ||
| Single-ended Output Rise/Fall (20-80%), CMOS | CKOTRF | 8 | ns | CMOS Output, VDD = 1.62 V, Cload = 5 pF | 11 | ||
| Single-ended Output Rise/Fall (20-80%), CMOS | CKOTRF | 2 | ns | CMOS Output, VDD = 2.97 V, Cload = 5 pF | 11 | ||
| Differential Output Rise/Fall Time | CKOTRF | 230 | 350 | ps | 20 to 80 %, fOUT = 622.08 MHz | 11 | |
| Output Duty Cycle Differential Uncertainty | CKODC | -40 | 40 | ps | 100 Ω Load Line to Line; Measured at 50% Point (not for CMOS) | 11 | |
| Lock Time | tLOCKHW | 1.2 | sec | Whenever RST, FRQTBL, RATE, BWSEL, or FRQSEL are changed, with valid CKIN to LOL; BW = 100 Hz | 12 | ||
| Output clock frequency range (Si5317C variant) | 1 | 200 | MHz | Ordering Guide, Si5317C-C-GM output clock freq range | 40 | ||
| Jitter Generation (12 kHz-20 MHz) | JGEN | 0.31 | 0.41 | ps rms | fIN = fOUT = 622.08 MHz, LVPECL output format, BW = 120 Hz, 12 kHz-20 MHz | 12 | |
| Thermal Resistance Junction to Ambient | JA | 32 | ºC/W | Still Air | 13 | ||
| Thermal Resistance Junction to Case | JC | 14 | ºC/W | 13 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body | 41 |
CAD (KiCad official)
- Symbol:
SI5317C-C-GMR - Footprint:
Package_DFN_QFN:QFN-36-1EP_6x6mm_P0.5mm_EP3.7x3.7mm - 3D model: QFN-36-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
si5317c-c-gmr-etched.step/si5317c-c-gmr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si5317c-c-gmr.step/si5317c-c-gmr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SKYWORKS SILICON LABS datasheet (46 pp, sha256
bf5e9ec3b0439041, retrieved 2026-11-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).