main
Ray Publish 0.1.0 efc0563

SI4460-B1B-FMR

SILICON LABS · RF Transceiver ICs · QFN-20-EP(4x4)

SI4460-B1B-FMR from SILICON LABS, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SDN input Shutdown input, 0-VDD V digital; must be 0 in all modes except Shutdown, and when SDN = 1 the chip is completely shut down and register contents are lost.
2 RXp input Differential RF input of the LNA, used with an external matching network per the application schematic.
3 RXn input Differential RF input of the LNA, used with an external matching network per the application schematic.
4 TX output Transmit output; the PA output is open-drain so the L-C match must supply VDD (+3.3 VDC nominal) to this pin.
5 NC unconnected No connect; not connected internally to any circuitry.
6 VDD power_in +1.8 to +3.6 V supply input to internal regulators, recommended +3.3 V.
7 TXRAMP output Programmable bias output with ramp capability for an external FET PA.
8 VDD power_in +1.8 to +3.6 V supply input to internal regulators, recommended +3.3 V.
9 GPIO0 bidirectional General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
10 GPIO1 bidirectional General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
11 nIRQ output Active-low microcontroller interrupt status output (low = 0 on an interrupt event); no external pull-up required but may be desirable with multiple interrupt lines.
12 SCLK input Serial clock input, 0-VDD V digital, for the 4-line serial bus; data is clocked in on positive edges.
13 SDO output 0-VDD V digital output providing serial readback of the internal control registers.
14 SDI input Serial data input, 0-VDD V digital, for the 4-line serial data bus.
15 nSEL input Serial interface select/enable input, 0-VDD V digital, for the 4-line serial bus.
16 XOUT output Crystal oscillator output; connect to an external 25 to 32 MHz crystal, or leave floating when driving XIN with an external source.
17 XIN input Crystal oscillator input; connect to an external 25 to 32 MHz crystal or to an external source.
18 GND power_in Connect to PCB ground.
19 GPIO2 bidirectional General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
20 GPIO3 bidirectional General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control.
21 PADDLE_GND power_in Exposed paddle supplying RF and circuit ground for the entire chip; needs a good solder connection to the PCB ground plane.

Key specifications

Parameter Value
Manufacturer SILICON LABS
Package QFN-20-EP(4x4)
Category RF & Radio
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Range VDD 1.8 3.3 3.6 V 4
Synthesizer Frequency Range (Si4463/61/60) band 1 FSYN 850 1050 MHz 5
Synthesizer Frequency Range (Si4463/61/60) band 2 FSYN 420 525 MHz 5
Synthesizer Frequency Range (Si4463/61/60) band 3 FSYN 284 350 MHz 5
Synthesizer Frequency Range (Si4463/61/60) band 4 FSYN 142 175 MHz 5
RX Frequency Range (Si4463/61/60) band 1 FRX 850 1050 MHz 6
RX Frequency Range (Si4463/61/60) band 2 FRX 420 525 MHz 6
RX Frequency Range (Si4463/61/60) band 3 FRX 284 350 MHz 6
RX Frequency Range (Si4463/61/60) band 4 FRX 142 175 MHz 6
RX Channel Bandwidth BW 1.1 850 kHz 7
BER Variation vs Power Level PRX_RES 0 0.1 ppm Up to +5 dBm Input Level 7
TX Frequency Range (Si4463/61/60) band 1 FTX 850 1050 MHz 9
TX Frequency Range (Si4463/61/60) band 2 FTX 420 525 MHz 9
TX Frequency Range (Si4463/61/60) band 3 FTX 284 350 MHz 9
TX Frequency Range (Si4463/61/60) band 4 FTX 142 175 MHz 9
(G)FSK Data Rate DRFSK 0.1 500 kbps 9
4(G)FSK Data Rate DR4FSK 0.2 1000 kbps 9
OOK Data Rate DROOK 0.1 120 kbps 9
Output Power Range (Si4460) PTX60 -40 13 dBm 10
XTAL Range XTALRange 25 32 MHz 11
POR Reset Time tPOR 5 ms 11
Logic High Level Input Voltage VIH 0.7 x VDD printed as VDD x 0.7 12
Logic Low Level Input Voltage VIL 0.3 x VDD printed as VDD x 0.3 12
Input Current IIN -10 10 µA 0<VIN< VDD 12
Input Current If Pullup is Activated IINP 1 10 µA VIL = 0 V 12
Logic High Level Output Voltage VOH 0.8 x VDD DRV[1:0] = HL; printed as VDD x 0.8 12
Logic Low Level Output Voltage VOL 0.2 x VDD DRV[1:0] = HL; printed as VDD x 0.2 12
VDD to GND VDD -0.3 3.6 V 13
Instantaneous VRF-peak to GND on TX Output Pin VRF-peak -0.3 8 V 13
Sustained VRF-peak to GND on TX Output Pin VRF-peak -0.3 6.5 V 13
Voltage on Digital Control Inputs -0.3 V max printed as VDD + 0.3 13
Voltage on Analog Inputs -0.3 V max printed as VDD + 0.3 13
RX Input Power 10 dBm 13
Operating Ambient Temperature Range TA -40 85 C 13
Junction Temperature TJ 125 C 13
Storage Temperature Range TSTG -55 125 C 13
Thermal Impedance θJA 30 C/W 13
Shutdown Current IShutdown 30 nA RC Oscillator, Main Digital Regulator, and Low Power Digital Regulator OFF 4
Standby Current IStandby 50 nA Register values maintained and RC oscillator/WUT OFF 4
Sleep Current RC ISleepRC 900 nA RC Oscillator/WUT ON and all register values maintained, and all other blocks OFF 4
Ready Mode Current IReady 1.8 mA Crystal Oscillator and Main Digital Regulator ON, all other blocks OFF 4
RX Mode Current High Performance IRXH 13.7 mA High Performance Mode 4
RX Mode Current Low Power IRXL 10.7 mA Low Power Mode 4
TX Mode Current (Si4460) ITX_+10 18 mA +10 dBm output power, Class-E match, 868 MHz, 3.3 V 4
RX Sensitivity PRX_0.5 -126 dBm BER < 0.1%, 500 bps, GFSK, BT = 0.5 7

CAD (KiCad official)

  • Symbol: SI4460-B1B-FMR
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: si4460-b1b-fmr-etched.step / si4460-b1b-fmr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si4460-b1b-fmr.step / si4460-b1b-fmr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SILICON LABS datasheet (56 pp, sha256 45177ecaf152d97b, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF