Generated by kicad-footprint-generator · KiCad file format 20260206
SI4460-B1B-FMR
SILICON LABS · RF Transceiver ICs · QFN-20-EP(4x4)
SI4460-B1B-FMR from SILICON LABS, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDN | input | Shutdown input, 0-VDD V digital; must be 0 in all modes except Shutdown, and when SDN = 1 the chip is completely shut down and register contents are lost. |
| 2 | RXp | input | Differential RF input of the LNA, used with an external matching network per the application schematic. |
| 3 | RXn | input | Differential RF input of the LNA, used with an external matching network per the application schematic. |
| 4 | TX | output | Transmit output; the PA output is open-drain so the L-C match must supply VDD (+3.3 VDC nominal) to this pin. |
| 5 | NC | unconnected | No connect; not connected internally to any circuitry. |
| 6 | VDD | power_in | +1.8 to +3.6 V supply input to internal regulators, recommended +3.3 V. |
| 7 | TXRAMP | output | Programmable bias output with ramp capability for an external FET PA. |
| 8 | VDD | power_in | +1.8 to +3.6 V supply input to internal regulators, recommended +3.3 V. |
| 9 | GPIO0 | bidirectional | General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 10 | GPIO1 | bidirectional | General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 11 | nIRQ | output | Active-low microcontroller interrupt status output (low = 0 on an interrupt event); no external pull-up required but may be desirable with multiple interrupt lines. |
| 12 | SCLK | input | Serial clock input, 0-VDD V digital, for the 4-line serial bus; data is clocked in on positive edges. |
| 13 | SDO | output | 0-VDD V digital output providing serial readback of the internal control registers. |
| 14 | SDI | input | Serial data input, 0-VDD V digital, for the 4-line serial data bus. |
| 15 | nSEL | input | Serial interface select/enable input, 0-VDD V digital, for the 4-line serial bus. |
| 16 | XOUT | output | Crystal oscillator output; connect to an external 25 to 32 MHz crystal, or leave floating when driving XIN with an external source. |
| 17 | XIN | input | Crystal oscillator input; connect to an external 25 to 32 MHz crystal or to an external source. |
| 18 | GND | power_in | Connect to PCB ground. |
| 19 | GPIO2 | bidirectional | General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 20 | GPIO3 | bidirectional | General purpose digital I/O configurable via registers for functions such as clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 21 | PADDLE_GND | power_in | Exposed paddle supplying RF and circuit ground for the entire chip; needs a good solder connection to the PCB ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-20-EP(4x4) |
| Category | RF & Radio |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | VDD | 1.8 | 3.3 | 3.6 | V | 4 | |
| Synthesizer Frequency Range (Si4463/61/60) band 1 | FSYN | 850 | 1050 | MHz | 5 | ||
| Synthesizer Frequency Range (Si4463/61/60) band 2 | FSYN | 420 | 525 | MHz | 5 | ||
| Synthesizer Frequency Range (Si4463/61/60) band 3 | FSYN | 284 | 350 | MHz | 5 | ||
| Synthesizer Frequency Range (Si4463/61/60) band 4 | FSYN | 142 | 175 | MHz | 5 | ||
| RX Frequency Range (Si4463/61/60) band 1 | FRX | 850 | 1050 | MHz | 6 | ||
| RX Frequency Range (Si4463/61/60) band 2 | FRX | 420 | 525 | MHz | 6 | ||
| RX Frequency Range (Si4463/61/60) band 3 | FRX | 284 | 350 | MHz | 6 | ||
| RX Frequency Range (Si4463/61/60) band 4 | FRX | 142 | 175 | MHz | 6 | ||
| RX Channel Bandwidth | BW | 1.1 | 850 | kHz | 7 | ||
| BER Variation vs Power Level | PRX_RES | 0 | 0.1 | ppm | Up to +5 dBm Input Level | 7 | |
| TX Frequency Range (Si4463/61/60) band 1 | FTX | 850 | 1050 | MHz | 9 | ||
| TX Frequency Range (Si4463/61/60) band 2 | FTX | 420 | 525 | MHz | 9 | ||
| TX Frequency Range (Si4463/61/60) band 3 | FTX | 284 | 350 | MHz | 9 | ||
| TX Frequency Range (Si4463/61/60) band 4 | FTX | 142 | 175 | MHz | 9 | ||
| (G)FSK Data Rate | DRFSK | 0.1 | 500 | kbps | 9 | ||
| 4(G)FSK Data Rate | DR4FSK | 0.2 | 1000 | kbps | 9 | ||
| OOK Data Rate | DROOK | 0.1 | 120 | kbps | 9 | ||
| Output Power Range (Si4460) | PTX60 | -40 | 13 | dBm | 10 | ||
| XTAL Range | XTALRange | 25 | 32 | MHz | 11 | ||
| POR Reset Time | tPOR | 5 | ms | 11 | |||
| Logic High Level Input Voltage | VIH | 0.7 | x VDD | printed as VDD x 0.7 | 12 | ||
| Logic Low Level Input Voltage | VIL | 0.3 | x VDD | printed as VDD x 0.3 | 12 | ||
| Input Current | IIN | -10 | 10 | µA | 0<VIN< VDD | 12 | |
| Input Current If Pullup is Activated | IINP | 1 | 10 | µA | VIL = 0 V | 12 | |
| Logic High Level Output Voltage | VOH | 0.8 | x VDD | DRV[1:0] = HL; printed as VDD x 0.8 | 12 | ||
| Logic Low Level Output Voltage | VOL | 0.2 | x VDD | DRV[1:0] = HL; printed as VDD x 0.2 | 12 | ||
| VDD to GND | VDD | -0.3 | 3.6 | V | 13 | ||
| Instantaneous VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 8 | V | 13 | ||
| Sustained VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 6.5 | V | 13 | ||
| Voltage on Digital Control Inputs | -0.3 | V | max printed as VDD + 0.3 | 13 | |||
| Voltage on Analog Inputs | -0.3 | V | max printed as VDD + 0.3 | 13 | |||
| RX Input Power | 10 | dBm | 13 | ||||
| Operating Ambient Temperature Range | TA | -40 | 85 | C | 13 | ||
| Junction Temperature | TJ | 125 | C | 13 | |||
| Storage Temperature Range | TSTG | -55 | 125 | C | 13 | ||
| Thermal Impedance | θJA | 30 | C/W | 13 | |||
| Shutdown Current | IShutdown | 30 | nA | RC Oscillator, Main Digital Regulator, and Low Power Digital Regulator OFF | 4 | ||
| Standby Current | IStandby | 50 | nA | Register values maintained and RC oscillator/WUT OFF | 4 | ||
| Sleep Current RC | ISleepRC | 900 | nA | RC Oscillator/WUT ON and all register values maintained, and all other blocks OFF | 4 | ||
| Ready Mode Current | IReady | 1.8 | mA | Crystal Oscillator and Main Digital Regulator ON, all other blocks OFF | 4 | ||
| RX Mode Current High Performance | IRXH | 13.7 | mA | High Performance Mode | 4 | ||
| RX Mode Current Low Power | IRXL | 10.7 | mA | Low Power Mode | 4 | ||
| TX Mode Current (Si4460) | ITX_+10 | 18 | mA | +10 dBm output power, Class-E match, 868 MHz, 3.3 V | 4 | ||
| RX Sensitivity | PRX_0.5 | -126 | dBm | BER < 0.1%, 500 bps, GFSK, BT = 0.5 | 7 |
CAD (KiCad official)
- Symbol:
SI4460-B1B-FMR - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
si4460-b1b-fmr-etched.step/si4460-b1b-fmr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si4460-b1b-fmr.step/si4460-b1b-fmr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (56 pp, sha256
45177ecaf152d97b, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).