main
Ray
si12t: the pins were read twice by one model (sonnet); say so instead of 'cross-checked by two models'
bf935cd
Si12T
Nanjing Zhongke Microelectronics · Touch Sensors · QFN-32-EP(5x5)
Si12T from Nanjing Zhongke Microelectronics, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IBA | input | Internal bias adjustment pin; a resistor RB (recommended 100 kΩ to 1500 kΩ, typ. 510 kΩ) sets oscillator and bias current, with CB (typ. 820 pF, max 1.5 nF) connected to VDD. |
| 2 | SBA | input | Internal bias adjustment in sleep mode; resistor RSB is connected here to reduce sleep-mode current. |
| 3 | TS5 | input | Touch sensor 5 input. |
| 4 | TS6 | input | Touch sensor 6 input. |
| 5 | TS7 | input | Touch sensor 7 input. |
| 6 | TS8 | input | Touch sensor 8 input. |
| 7 | TS9 | input | Touch sensor 9 input. |
| 8 | SCT | input | Touch detection suspension control: touch detection is paused when high, and the chip works normally when low or floating. |
| 9 | TS10 | input | Touch sensor 10 input. |
| 10 | VDD | power_in | Power supply pin, operating range 1.8 V to 5.0 V. |
| 11 | TS11 | input | Touch sensor 11 input. |
| 12 | TS12 | input | Touch sensor 12 input. |
| 13 | VSS | power_in | Ground pin. |
| 14 | N.C. | unconnected | No connection; leave floating. |
| 15 | I2C_BA | input | Internal I2C clock adjustment; resistor RIB sets the I2C internal clock frequency, and a smaller RIB gives higher clock frequency and I2C supply current. |
| 16 | RST | input | System reset input, active high. |
| 17 | OUT1 | output | Channel 1 output, open drain. |
| 18 | SCL | input | I2C clock input. |
| 19 | SDA | bidirectional | I2C data input/output. |
| 20 | IRQ | output | Interrupt output, open drain. |
| 21 | I2C_EN | input | I2C enable input, active low. |
| 22 | ID_SEL | input | I2C device address select: GND gives address 0xD0 and VDD gives 0xF0. |
| 23 | TS1_SEN0 | input | TS1 sensitivity control bit 0. |
| 24 | TS1_SEN1 | input | TS1 sensitivity control bit 1. |
| 25 | TS1_SEN2 | input | TS1 sensitivity control bit 2; TS1_SEN[2:0]=011 gives channel 1 sensitivity from the register. |
| 26 | VSS | power_in | Ground pin. |
| 27 | MODE | bidirectional | Output mode control (high: single channel output, low: multi-channel output), also used as the synchronization pin for multi-chip applications with typical RMODE pull-down of 2.2 MΩ. |
| 28 | VDD | power_in | Power supply pin, 1.8 V to 5.0 V. |
| 29 | TS1 | input | Touch sensor 1 input. |
| 30 | TS2 | input | Touch sensor 2 input. |
| 31 | TS3 | input | Touch sensor 3 input. |
| 32 | TS4 | input | Touch sensor 4 input. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nanjing Zhongke Microelectronics |
| Package | QFN-32-EP(5x5) |
| Category | Sensors |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating voltage | VDD | 1.8 | 3.3 | 5 | V | 12 | |
| Input induction capacitance range | CS | 10 | 110 | pF | 12 | ||
| Input induction resistance range | RS | 200 | 2000 | Ω | 12 | ||
| Minimum detectable ΔC | 0.2 | pF | CS = 10 pF, CDEG = 200 pF (I2C default sensitivity) | 12 | |||
| Recommended offset resistance | RB | 100 | 510 | 1500 | KΩ | VDD = 3.3 V | 13 |
| Maximum offset capacitance | CB_MAX | 820 | 1500 | pF | 13 | ||
| Recommended synchronous resistance range | RSYNC | 0.91 | 2 | 20 | MΩ | 13 | |
| Supply voltage | 5 | V | Battery supply power | 10 | |||
| Maximum voltage on any pin | 0.3 | V | printed as VDD+0.3 | 10 | |||
| Maximum current on any pad | 100 | mA | 10 | ||||
| Dissipated power | 800 | mW | 10 | ||||
| Storage temperature | -50 | 150 | ℃ | 10 | |||
| Operating temperature | -20 | 75 | ℃ | 10 | |||
| Junction temperature | 150 | ℃ | 10 | ||||
| Power consumption current | IDD | 67.68 | µA | VDD = 3.3 V RB = 510 K R_SB=0 | 12 | ||
| Power consumption current | IDD | 145 | µA | VDD = 5.0 V RB = 510 K R_SB=0 | 12 | ||
| Non-sensing power consumption current | IDD | 3.48 | µA | VDD = 3.3 V RB = 510 K R_SB=6 M | 12 | ||
| Non-sensing power consumption current | IDD | 10.44 | µA | VDD = 5.0 V RB = 510 K R_SB=6 M | 12 | ||
| I2C current | IDD_I2C | 0.67 | mA | VDD = 3.3 V RB = 510 K RI2C=20 k | 12 | ||
| I2C current | IDD_I2C | 1.1 | mA | VDD = 5.0 V RB = 510 K RI2C=20 k | 12 | ||
| I2C disable current | IDD_I2C | 0.04 | nA | I2C Disable | 12 | ||
| Output impedance | ZO | 71 | Ω | ΔC > 0.2 pF, CS = 10 pF (I2C default sensitivity) | 13 | ||
| Self-examination time after reset | TCAL | 120 | ms | VDD = 3.3 V RB = 510 K | 13 | ||
| Self-examination time after reset | TCAL | 98 | ms | VDD = 5.0 V RB = 510 K | 13 |
CAD (KiCad official)
- Symbol:
Si12T - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
si12t-etched.step/si12t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si12t.step/si12t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nanjing Zhongke Microelectronics datasheet (32 pp, sha256
389b2fc7d569b692, retrieved 2026-10-26, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# Si12T
**Nanjing Zhongke Microelectronics** · Touch Sensors · QFN-32-EP(5x5)
Si12T from Nanjing Zhongke Microelectronics, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IBA | input | Internal bias adjustment pin; a resistor RB (recommended 100 kΩ to 1500 kΩ, typ. 510 kΩ) sets oscillator and bias current, with CB (typ. 820 pF, max 1.5 nF) connected to VDD. |
| 2 | SBA | input | Internal bias adjustment in sleep mode; resistor RSB is connected here to reduce sleep-mode current. |
| 3 | TS5 | input | Touch sensor 5 input. |
| 4 | TS6 | input | Touch sensor 6 input. |
| 5 | TS7 | input | Touch sensor 7 input. |
| 6 | TS8 | input | Touch sensor 8 input. |
| 7 | TS9 | input | Touch sensor 9 input. |
| 8 | SCT | input | Touch detection suspension control: touch detection is paused when high, and the chip works normally when low or floating. |
| 9 | TS10 | input | Touch sensor 10 input. |
| 10 | VDD | power_in | Power supply pin, operating range 1.8 V to 5.0 V. |
| 11 | TS11 | input | Touch sensor 11 input. |
| 12 | TS12 | input | Touch sensor 12 input. |
| 13 | VSS | power_in | Ground pin. |
| 14 | N.C. | unconnected | No connection; leave floating. |
| 15 | I2C_BA | input | Internal I2C clock adjustment; resistor RIB sets the I2C internal clock frequency, and a smaller RIB gives higher clock frequency and I2C supply current. |
| 16 | RST | input | System reset input, active high. |
| 17 | OUT1 | output | Channel 1 output, open drain. |
| 18 | SCL | input | I2C clock input. |
| 19 | SDA | bidirectional | I2C data input/output. |
| 20 | IRQ | output | Interrupt output, open drain. |
| 21 | I2C_EN | input | I2C enable input, active low. |
| 22 | ID_SEL | input | I2C device address select: GND gives address 0xD0 and VDD gives 0xF0. |
| 23 | TS1_SEN0 | input | TS1 sensitivity control bit 0. |
| 24 | TS1_SEN1 | input | TS1 sensitivity control bit 1. |
| 25 | TS1_SEN2 | input | TS1 sensitivity control bit 2; TS1_SEN[2:0]=011 gives channel 1 sensitivity from the register. |
| 26 | VSS | power_in | Ground pin. |
| 27 | MODE | bidirectional | Output mode control (high: single channel output, low: multi-channel output), also used as the synchronization pin for multi-chip applications with typical RMODE pull-down of 2.2 MΩ. |
| 28 | VDD | power_in | Power supply pin, 1.8 V to 5.0 V. |
| 29 | TS1 | input | Touch sensor 1 input. |
| 30 | TS2 | input | Touch sensor 2 input. |
| 31 | TS3 | input | Touch sensor 3 input. |
| 32 | TS4 | input | Touch sensor 4 input. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nanjing Zhongke Microelectronics |
| Package | QFN-32-EP(5x5) |
| Category | Sensors |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating voltage | VDD | 1.8 | 3.3 | 5 | V | | 12 |
| Input induction capacitance range | CS | | 10 | 110 | pF | | 12 |
| Input induction resistance range | RS | 200 | | 2000 | Ω | | 12 |
| Minimum detectable ΔC | | 0.2 | | | pF | CS = 10 pF, CDEG = 200 pF (I2C default sensitivity) | 12 |
| Recommended offset resistance | RB | 100 | 510 | 1500 | KΩ | VDD = 3.3 V | 13 |
| Maximum offset capacitance | CB_MAX | | 820 | 1500 | pF | | 13 |
| Recommended synchronous resistance range | RSYNC | 0.91 | 2 | 20 | MΩ | | 13 |
| Supply voltage | | | | 5 | V | Battery supply power | 10 |
| Maximum voltage on any pin | | | | 0.3 | V | printed as VDD+0.3 | 10 |
| Maximum current on any pad | | | | 100 | mA | | 10 |
| Dissipated power | | | | 800 | mW | | 10 |
| Storage temperature | | -50 | | 150 | ℃ | | 10 |
| Operating temperature | | -20 | | 75 | ℃ | | 10 |
| Junction temperature | | | | 150 | ℃ | | 10 |
| Power consumption current | IDD | | 67.68 | | µA | VDD = 3.3 V RB = 510 K R_SB=0 | 12 |
| Power consumption current | IDD | | 145 | | µA | VDD = 5.0 V RB = 510 K R_SB=0 | 12 |
| Non-sensing power consumption current | IDD | | 3.48 | | µA | VDD = 3.3 V RB = 510 K R_SB=6 M | 12 |
| Non-sensing power consumption current | IDD | | 10.44 | | µA | VDD = 5.0 V RB = 510 K R_SB=6 M | 12 |
| I2C current | IDD_I2C | | 0.67 | | mA | VDD = 3.3 V RB = 510 K RI2C=20 k | 12 |
| I2C current | IDD_I2C | | 1.1 | | mA | VDD = 5.0 V RB = 510 K RI2C=20 k | 12 |
| I2C disable current | IDD_I2C | | 0.04 | | nA | I2C Disable | 12 |
| Output impedance | ZO | | 71 | | Ω | ΔC > 0.2 pF, CS = 10 pF (I2C default sensitivity) | 13 |
| Self-examination time after reset | TCAL | | 120 | | ms | VDD = 3.3 V RB = 510 K | 13 |
| Self-examination time after reset | TCAL | | 98 | | ms | VDD = 5.0 V RB = 510 K | 13 |
## CAD (KiCad official)
- Symbol: `Si12T`
- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`
- 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `si12t-etched.step` / `si12t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `si12t.step` / `si12t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Nanjing Zhongke Microelectronics datasheet](docs/si12t-datasheet.pdf) (32 pp, sha256 `389b2fc7d569b692`, retrieved 2026-10-26, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/si12t-datasheet.pdf)