Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

Si12T

Nanjing Zhongke Microelectronics · Touch Sensors · QFN-32-EP(5x5)

Si12T from Nanjing Zhongke Microelectronics, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IBA input Internal bias adjustment pin; a resistor RB (recommended 100 kΩ to 1500 kΩ, typ. 510 kΩ) sets oscillator and bias current, with CB (typ. 820 pF, max 1.5 nF) connected to VDD.
2 SBA input Internal bias adjustment in sleep mode; resistor RSB is connected here to reduce sleep-mode current.
3 TS5 input Touch sensor 5 input.
4 TS6 input Touch sensor 6 input.
5 TS7 input Touch sensor 7 input.
6 TS8 input Touch sensor 8 input.
7 TS9 input Touch sensor 9 input.
8 SCT input Touch detection suspension control: touch detection is paused when high, and the chip works normally when low or floating.
9 TS10 input Touch sensor 10 input.
10 VDD power_in Power supply pin, operating range 1.8 V to 5.0 V.
11 TS11 input Touch sensor 11 input.
12 TS12 input Touch sensor 12 input.
13 VSS power_in Ground pin.
14 N.C. unconnected No connection; leave floating.
15 I2C_BA input Internal I2C clock adjustment; resistor RIB sets the I2C internal clock frequency, and a smaller RIB gives higher clock frequency and I2C supply current.
16 RST input System reset input, active high.
17 OUT1 output Channel 1 output, open drain.
18 SCL input I2C clock input.
19 SDA bidirectional I2C data input/output.
20 IRQ output Interrupt output, open drain.
21 I2C_EN input I2C enable input, active low.
22 ID_SEL input I2C device address select: GND gives address 0xD0 and VDD gives 0xF0.
23 TS1_SEN0 input TS1 sensitivity control bit 0.
24 TS1_SEN1 input TS1 sensitivity control bit 1.
25 TS1_SEN2 input TS1 sensitivity control bit 2; TS1_SEN[2:0]=011 gives channel 1 sensitivity from the register.
26 VSS power_in Ground pin.
27 MODE bidirectional Output mode control (high: single channel output, low: multi-channel output), also used as the synchronization pin for multi-chip applications with typical RMODE pull-down of 2.2 MΩ.
28 VDD power_in Power supply pin, 1.8 V to 5.0 V.
29 TS1 input Touch sensor 1 input.
30 TS2 input Touch sensor 2 input.
31 TS3 input Touch sensor 3 input.
32 TS4 input Touch sensor 4 input.
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Nanjing Zhongke Microelectronics
Package QFN-32-EP(5x5)
Category Sensors
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating voltage VDD 1.8 3.3 5 V 12
Input induction capacitance range CS 10 110 pF 12
Input induction resistance range RS 200 2000 Ω 12
Minimum detectable ΔC 0.2 pF CS = 10 pF, CDEG = 200 pF (I2C default sensitivity) 12
Recommended offset resistance RB 100 510 1500 KΩ VDD = 3.3 V 13
Maximum offset capacitance CB_MAX 820 1500 pF 13
Recommended synchronous resistance range RSYNC 0.91 2 20 MΩ 13
Supply voltage 5 V Battery supply power 10
Maximum voltage on any pin 0.3 V printed as VDD+0.3 10
Maximum current on any pad 100 mA 10
Dissipated power 800 mW 10
Storage temperature -50 150 ℃ 10
Operating temperature -20 75 ℃ 10
Junction temperature 150 ℃ 10
Power consumption current IDD 67.68 µA VDD = 3.3 V RB = 510 K R_SB=0 12
Power consumption current IDD 145 µA VDD = 5.0 V RB = 510 K R_SB=0 12
Non-sensing power consumption current IDD 3.48 µA VDD = 3.3 V RB = 510 K R_SB=6 M 12
Non-sensing power consumption current IDD 10.44 µA VDD = 5.0 V RB = 510 K R_SB=6 M 12
I2C current IDD_I2C 0.67 mA VDD = 3.3 V RB = 510 K RI2C=20 k 12
I2C current IDD_I2C 1.1 mA VDD = 5.0 V RB = 510 K RI2C=20 k 12
I2C disable current IDD_I2C 0.04 nA I2C Disable 12
Output impedance ZO 71 Ω ΔC > 0.2 pF, CS = 10 pF (I2C default sensitivity) 13
Self-examination time after reset TCAL 120 ms VDD = 3.3 V RB = 510 K 13
Self-examination time after reset TCAL 98 ms VDD = 5.0 V RB = 510 K 13

CAD (KiCad official)

  • Symbol: Si12T
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: si12t-etched.step / si12t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si12t.step / si12t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Nanjing Zhongke Microelectronics datasheet (32 pp, sha256 389b2fc7d569b692, retrieved 2026-10-26, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF