main
Ray
Publish 0.1.0
71e8deb
SHT40-AD1F-R2
Sensirion · Global Sourcing Parts · DFN-4(1.5x1.5)
SHT40-AD1F-R2 from Sensirion, in a DFN-4(1.5x1.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDA | bidirectional | Serial data line of the I2C interface, bidirectional. |
| 2 | SCL | input | Serial clock line of the I2C interface, specified by the datasheet as a unidirectional input. |
| 3 | VDD | power_in | Supply voltage; the datasheet gives the operating range VDD = 1.08 V to 3.6 V (page 1). |
| 4 | VSS | power_in | Ground; the die pad is not directly connected to any pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sensirion |
| Package | DFN-4(1.5x1.5) |
| Category | Global Sourcing Parts |
| Pins | 4 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 1.08 | 3.3 | 3.6 | V | 9 | |
| Power-up/down voltage, static power supply | VPOR | 0.6 | 1.08 | V | Static power supply | 9 | |
| Slew rate of the supply voltage | VDD, slew | 20 | V/ms | 9 | |||
| Supply current (heater off), idle state | IDD | 0.08 | 1 | µA | Idle state, at 25 °C | 9 | |
| Supply current (heater off), idle state | IDD | 3.4 | µA | Idle state, at 125 °C | 9 | ||
| Measurement supply current | IDD | 320 | 500 | µA | Current while sensor is measuring | 9 | |
| Supply current (heater on), nominal heater 200 mW | IDD | 60 | 100 | mA | Nominal heater “200 mW” | 9 | |
| Supply current (heater on), nominal heater 110 mW | IDD | 33 | 55 | mA | Nominal heater “110 mW” | 9 | |
| Supply current (heater on), nominal heater 20 mW | IDD | 6 | 10 | mA | Nominal heater “20 mW” | 9 | |
| Low level input voltage (max printed as 0.3*VDD) | VIL | 0 | 0.3 | *VDD | 9 | ||
| High level input voltage (min printed as 0.7*VDD; max printed as VDD) | VIH | 0.7 | *VDD | 9 | |||
| Pull up resistor Rp | Rp | 820 | Ω | VDD < 1.62 V | 9 | ||
| Pull up resistor Rp | Rp | 390 | Ω | VDD ≥ 1.62 V | 9 | ||
| Low level output voltage (max printed as 0.2*VDD) | VOL | 0.2 | *VDD | VDD < 1.62 V, Rpullup > 820 Ω | 9 | ||
| Low level output voltage | VOL | 0.4 | V | VDD > 2.0 V, Rpullup > 390 Ω | 9 | ||
| Capacitive bus load | Cb | 400 | pF | RP ≤ 820 Ω: fast mode | 9 | ||
| Capacitive bus load | Cb | 340 | pF | Rp = 390 Ω, VDD > 1.62 V: fast mode plus | 9 | ||
| Power-up time | tPU | 0.3 | 1 | ms | After hard reset, VDD ≥ VPOR | 10 | |
| Soft reset time | tSR | 1 | ms | After soft reset | 10 | ||
| Measurement duration, low repeatability | tMEAS,l | 1.3 | 1.6 | ms | Low repeatability | 10 | |
| Measurement duration, medium repeatability | tMEAS,m | 3.7 | 4.5 | ms | Med. repeatability | 10 | |
| Measurement duration, high repeatability | tMEAS,h | 6.9 | 8.3 | ms | High repeatability | 10 | |
| Heater-on duration, long pulse | tHeater | 0.9 | 1 | 1.1 | s | Long pulse | 10 |
| Heater-on duration, short pulse | tHeater | 0.09 | 0.1 | 0.11 | s | Short pulse | 10 |
| Max voltage on any pin | -0.3 | 0.3 | V | Min referenced to VSS; max referenced to VDD | 10 | ||
| Operating temperature range | -40 | 125 | °C | 10 | |||
| Storage temperature range | -40 | 150 | °C | 10 | |||
| ESD HBM | 2 | kV | 10 | ||||
| ESD CDM | 500 | V | 10 | ||||
| Latch up | 100 | mA | JESD78 Class II, 125 °C | 10 | |||
| Recommended normal temperature range | 5 | 60 | °C | Recommended normal range | 7 | ||
| Recommended normal relative humidity range | 20 | 80 | %RH | Recommended normal range | 7 | ||
| Heater maximum duty cycle | 10 | % | Heater maximum duty cycle | 13 | |||
| Heater ambient temperature limit | 65 | °C | Heater operated only in ambient temperatures below 65 °C | 14 | |||
| Supply current (heater off), power up | IDD | 50 | µA | Power up | 9 | ||
| Average current consumption, high repeatability | 2.2 | µA | Avg., high repeatability; continuous operation with 1 meas. per second | 9 | |||
| Average current consumption, medium repeatability | 1.2 | µA | Avg., med. repeatability; continuous operation with 1 meas. per second | 9 | |||
| Average current consumption, low repeatability | 0.4 | µA | Avg., low repeatability; continuous operation with 1 meas. per second | 9 | |||
| Power consumption at VDD=1.2 V (no heater), high repeatability | 2.6 | µW | Avg., high repeatability; continuous operation with 1 meas. per second | 9 | |||
| Power consumption at VDD=1.2 V (no heater), medium repeatability | 1.4 | µW | Avg., med. repeatability; continuous operation with 1 meas. per second | 9 | |||
| Power consumption at VDD=1.2 V (no heater), low repeatability | 0.5 | µW | Avg., low repeatability; continuous operation with 1 meas. per second | 9 | |||
| Junction-to-ambient thermal resistance | RθJA | 297 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-ambient thermal resistance | RθJA | 357 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-case thermal resistance | RθJC | 191 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-case thermal resistance | RθJC | 257 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-board thermal resistance | RθJB | 193 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-board thermal resistance | RθJB | 258 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-board characterization parameter | ΨJB | 191 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-board characterization parameter | ΨJB | 254 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-top characterization parameter | ΨJT | 44 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-top characterization parameter | ΨJT | 112 | K/W | Heater on, die pad not soldered | 16 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | SHT4x is provided in an open-cavity dual flat no lead (DFN) package. The humidity sensor opening is centered on the top side of the package. The sensor chip is made of silicon, hosted on a copper lead | 14 |
CAD (KiCad official)
- Symbol:
SHT40-AD1F-R2 - Footprint:
Sensor_Humidity:Sensirion_DFN-4_1.5x1.5mm_P0.8mm_SHT4x_NoCentralPad - 3D model: DFN-4(1.5x1.5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
sht40-ad1f-r2-etched.step/sht40-ad1f-r2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sht40-ad1f-r2.step/sht40-ad1f-r2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sensirion datasheet (23 pp, sha256
ed3d2b1894721bb0, retrieved 2026-11-07, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SHT40-AD1F-R2
**Sensirion** · Global Sourcing Parts · DFN-4(1.5x1.5)
SHT40-AD1F-R2 from Sensirion, in a DFN-4(1.5x1.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDA | bidirectional | Serial data line of the I2C interface, bidirectional. |
| 2 | SCL | input | Serial clock line of the I2C interface, specified by the datasheet as a unidirectional input. |
| 3 | VDD | power_in | Supply voltage; the datasheet gives the operating range VDD = 1.08 V to 3.6 V (page 1). |
| 4 | VSS | power_in | Ground; the die pad is not directly connected to any pin. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sensirion |
| Package | DFN-4(1.5x1.5) |
| Category | Global Sourcing Parts |
| Pins | 4 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 1.08 | 3.3 | 3.6 | V | | 9 |
| Power-up/down voltage, static power supply | VPOR | 0.6 | | 1.08 | V | Static power supply | 9 |
| Slew rate of the supply voltage | VDD, slew | | | 20 | V/ms | | 9 |
| Supply current (heater off), idle state | IDD | | 0.08 | 1 | µA | Idle state, at 25 °C | 9 |
| Supply current (heater off), idle state | IDD | | | 3.4 | µA | Idle state, at 125 °C | 9 |
| Measurement supply current | IDD | | 320 | 500 | µA | Current while sensor is measuring | 9 |
| Supply current (heater on), nominal heater 200 mW | IDD | | 60 | 100 | mA | Nominal heater “200 mW” | 9 |
| Supply current (heater on), nominal heater 110 mW | IDD | | 33 | 55 | mA | Nominal heater “110 mW” | 9 |
| Supply current (heater on), nominal heater 20 mW | IDD | | 6 | 10 | mA | Nominal heater “20 mW” | 9 |
| Low level input voltage (max printed as 0.3*VDD) | VIL | 0 | | 0.3 | *VDD | | 9 |
| High level input voltage (min printed as 0.7*VDD; max printed as VDD) | VIH | 0.7 | | | *VDD | | 9 |
| Pull up resistor Rp | Rp | 820 | | | Ω | VDD < 1.62 V | 9 |
| Pull up resistor Rp | Rp | 390 | | | Ω | VDD ≥ 1.62 V | 9 |
| Low level output voltage (max printed as 0.2*VDD) | VOL | | | 0.2 | *VDD | VDD < 1.62 V, Rpullup > 820 Ω | 9 |
| Low level output voltage | VOL | | | 0.4 | V | VDD > 2.0 V, Rpullup > 390 Ω | 9 |
| Capacitive bus load | Cb | | | 400 | pF | RP ≤ 820 Ω: fast mode | 9 |
| Capacitive bus load | Cb | | | 340 | pF | Rp = 390 Ω, VDD > 1.62 V: fast mode plus | 9 |
| Power-up time | tPU | | 0.3 | 1 | ms | After hard reset, VDD ≥ VPOR | 10 |
| Soft reset time | tSR | | | 1 | ms | After soft reset | 10 |
| Measurement duration, low repeatability | tMEAS,l | | 1.3 | 1.6 | ms | Low repeatability | 10 |
| Measurement duration, medium repeatability | tMEAS,m | | 3.7 | 4.5 | ms | Med. repeatability | 10 |
| Measurement duration, high repeatability | tMEAS,h | | 6.9 | 8.3 | ms | High repeatability | 10 |
| Heater-on duration, long pulse | tHeater | 0.9 | 1 | 1.1 | s | Long pulse | 10 |
| Heater-on duration, short pulse | tHeater | 0.09 | 0.1 | 0.11 | s | Short pulse | 10 |
| Max voltage on any pin | | -0.3 | | 0.3 | V | Min referenced to VSS; max referenced to VDD | 10 |
| Operating temperature range | | -40 | | 125 | °C | | 10 |
| Storage temperature range | | -40 | | 150 | °C | | 10 |
| ESD HBM | | | | 2 | kV | | 10 |
| ESD CDM | | | | 500 | V | | 10 |
| Latch up | | | | 100 | mA | JESD78 Class II, 125 °C | 10 |
| Recommended normal temperature range | | 5 | | 60 | °C | Recommended normal range | 7 |
| Recommended normal relative humidity range | | 20 | | 80 | %RH | Recommended normal range | 7 |
| Heater maximum duty cycle | | | | 10 | % | Heater maximum duty cycle | 13 |
| Heater ambient temperature limit | | | | 65 | °C | Heater operated only in ambient temperatures below 65 °C | 14 |
| Supply current (heater off), power up | IDD | | 50 | | µA | Power up | 9 |
| Average current consumption, high repeatability | | | 2.2 | | µA | Avg., high repeatability; continuous operation with 1 meas. per second | 9 |
| Average current consumption, medium repeatability | | | 1.2 | | µA | Avg., med. repeatability; continuous operation with 1 meas. per second | 9 |
| Average current consumption, low repeatability | | | 0.4 | | µA | Avg., low repeatability; continuous operation with 1 meas. per second | 9 |
| Power consumption at VDD=1.2 V (no heater), high repeatability | | | 2.6 | | µW | Avg., high repeatability; continuous operation with 1 meas. per second | 9 |
| Power consumption at VDD=1.2 V (no heater), medium repeatability | | | 1.4 | | µW | Avg., med. repeatability; continuous operation with 1 meas. per second | 9 |
| Power consumption at VDD=1.2 V (no heater), low repeatability | | | 0.5 | | µW | Avg., low repeatability; continuous operation with 1 meas. per second | 9 |
| Junction-to-ambient thermal resistance | RθJA | | 297 | | K/W | Heater off, die pad not soldered | 16 |
| Junction-to-ambient thermal resistance | RθJA | | 357 | | K/W | Heater on, die pad not soldered | 16 |
| Junction-to-case thermal resistance | RθJC | | 191 | | K/W | Heater off, die pad not soldered | 16 |
| Junction-to-case thermal resistance | RθJC | | 257 | | K/W | Heater on, die pad not soldered | 16 |
| Junction-to-board thermal resistance | RθJB | | 193 | | K/W | Heater off, die pad not soldered | 16 |
| Junction-to-board thermal resistance | RθJB | | 258 | | K/W | Heater on, die pad not soldered | 16 |
| Junction-to-board characterization parameter | ΨJB | | 191 | | K/W | Heater off, die pad not soldered | 16 |
| Junction-to-board characterization parameter | ΨJB | | 254 | | K/W | Heater on, die pad not soldered | 16 |
| Junction-to-top characterization parameter | ΨJT | | 44 | | K/W | Heater off, die pad not soldered | 16 |
| Junction-to-top characterization parameter | ΨJT | | 112 | | K/W | Heater on, die pad not soldered | 16 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | SHT4x is provided in an open-cavity dual flat no lead (DFN) package. The humidity sensor opening is centered on the top side of the package. The sensor chip is made of silicon, hosted on a copper lead | 14 |
## CAD (KiCad official)
- Symbol: `SHT40-AD1F-R2`
- Footprint: `Sensor_Humidity:Sensirion_DFN-4_1.5x1.5mm_P0.8mm_SHT4x_NoCentralPad`
- 3D model: DFN-4(1.5x1.5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `sht40-ad1f-r2-etched.step` / `sht40-ad1f-r2-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sht40-ad1f-r2.step` / `sht40-ad1f-r2.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Sensirion datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590907640283279360) (23 pp, sha256 `ed3d2b1894721bb0`, retrieved 2026-11-07, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/sht40-ad1f-r2-datasheet.pdf)