SparkFun SEN-24540
SparkFun Electronics · SparkFun Qwiic Pulsed Coherent Radar Sensor XM125 · DigiKey 1568-24540-ND (listed by DigiKey as part 24540)
This page carries the breakout as a part, so a carrier board or a molecule can place it: the edge-hole pinout as a symbol, the two hole rows and the mounting holes as a footprint, and a 3D model.
Footprint
J14 (9 holes) and J15 (11 holes) at 2.54 mm on the long edges, and four 4-40 mounting holes, all from SparkFun's Eagle board file. The footprint origin is the centre of the hole pattern; F.Fab draws the board (25.4 x 50.8 mm) and the USB-C connector, which overhangs the top edge.
Pinout
Pin names: board silkscreen, from SparkFun's .brd (attached as docs/XM125_Breakout.brd), the label printed beside each hole on the top of the board; nets from the same file; functions from SparkFun's hardware overview. Pin 1 of each row is at the button end of the board.
J14
| No. | Label | Net | Function |
|---|---|---|---|
| 1 | RST | !XM125_RESET | Reset (active low); the RESET button pulls it to ground |
| 2 | CLK | SWD_CLK | SWDCLK, the XM125 STM32L431 programming clock |
| 3 | SIO | SWD_IO | SWDIO, the XM125 STM32L431 programming data |
| 4 | G | GND | Ground |
| 5 | G | GND | Ground |
| 6 | VU | V_USB | USB VBUS (VUSB), input to the 3.3 V regulator; no more than 6 V |
| 7 | 1V8 | 1.8V | 1.8 V from the RT9080 1.8 V regulator |
| 8 | 3V3 | 3.3V | 3.3 V rail |
| 9 | INT | !XM125_INT | Interrupt output (active low) from the XM125 |
J15
| No. | Label | Net | Function |
|---|---|---|---|
| 1 | WU | WAKE_UP | WAKE_UP: high wakes the XM125 from low power; tied to 3.3 V through the WU jumper |
| 2 | SCL | SCL | I2C clock (2.2 kOhm pull-up) |
| 3 | SDA | SDA | I2C data (2.2 kOhm pull-up) |
| 4 | 3V3 | 3.3V | 3.3 V rail |
| 5 | G | GND | Ground |
| 6 | ADDR | XM125_I2C_ADDRESS | I2C_ADDR, the XM125 I2C address select (also the ADDR jumper) |
| 7 | RX | DEBUG_UART-RX | Debug UART receive |
| 8 | TX | DEBUG_UART-TX | Debug UART transmit |
| 9 | IO0 | XM125_GPIO0 | XM125 GPIO0 (presence detector firmware) |
| 10 | IO1 | XM125_GPIO1 | XM125 GPIO1 |
| 11 | BOOT | XM125_GPIO2/BOOT0 | GPIO2/BOOT0: the BOOT button pulls it to 3.3 V for the bootloader |
3D model
Built from SparkFun's own Eagle board file, imported in KiCad 10: the real outline, red solder mask, white silkscreen with every printed label, copper pads, the plated edge holes and the four mounting holes. Every part sits at its board-file position, rotation and side (many are on the bottom), with a real model fitted to that part's pads:
- USB-C receptacle, both Qwiic (JST-SH 4-pin) connectors, the CH340C and both RT9080 regulators: models from our part pages (type-c-31-m-12, sm04b-srss-tb, ch340c, rt9080-33gj5). The Qwiic housings are black, as in SparkFun's photo.
- 0603 resistors, capacitors and the power LED, the SOT-23-6 ESD diode, and the two buttons (E-Switch TL3342, the nearest real 5.2 mm tact switch model): KiCad library models.
- The XM125 module: Acconeer's own module board (SRC-XM125 v1.1) with its part models, so the A121 radar sensor, the MCU, the crystal and the module silkscreen are Acconeer's.
The board ships without headers, so the model has none.
J13 (SWD, 2×5 1.27 mm) is not populated on the shipped board (DNP in SparkFun's board file: value "SWD (DNP)", package 2X5-SMD-UNSHROUDED_DNP_NO_PASTE; SparkFun's hardware overview: a footprint to solder an SMD 2x5 header); footprint shown bare on purpose.
Documents
Datasheet: Acconeer XM125 module (the radar on this board); SparkFun publishes no separate breakout datasheet.
- Hookup guide (SparkFun, web)
- Product page
- XM125 module datasheet (Acconeer, PDF, attached as docs/xm125-datasheet.pdf, shown as the page's datasheet): source
- Board schematic (SparkFun, PDF, attached) and the hardware repository (board file; hardware CC BY-SA 4.0)
Made from SparkFun's open hardware files (CC BY-SA 4.0); this page is shared under the same license.