main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs sct2620mrer: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers sct2620mrer: viewers · Ray
package.json Publish 0.2.1 · Ray
page.json Publish 0.2.1 · Ray
README.md sct2620mrer: specified limits as data (metadata.characteristics, 48 rows from the datasheet) · Ray
sct2620mrer-etched.fit.json sct2620mrer: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
sct2620mrer-etched.glb sct2620mrer: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
sct2620mrer-etched.step sct2620mrer: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
sct2620mrer-hero.glb sct2620mrer: hero from the plain model · Ray
sct2620mrer-hero.overlay.json sct2620mrer: hero from the plain model · Ray
sct2620mrer.glb Publish 0.1.0 · Ray
sct2620mrer.kicad_mod Publish 0.1.0 · Ray
sct2620mrer.kicad_sym Publish 0.1.0 · Ray
sct2620mrer.lbr Publish 0.1.0 · Ray
sct2620mrer.step Publish 0.1.0 · Ray

SCT2620MRER

SCT · DC-DC Converters · MSOP-10-EP

SCT2620MRER from SCT, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BOOT passive Power supply bias for high-side power MOSFET gate driver. Connect a 0.1 µF bootstrap capacitor from BOOT to SW; charged when SW voltage is low. Abs max 72 V. BOOT-SW UVLO ~2.5 V.
2 VIN power_in Input supply voltage, 3.8 V to 60 V (abs max 65 V). Connect a local bypass capacitor from VIN to GND with the shortest possible path to the high-frequency bypass cap.
3 EN input Enable pin with internal pull-up current (~4 µA at 1.5 V). Pull below 1.05 V to disable the converter; float or tie to VIN to enable. A resistor divider from VIN to GND on EN sets the programmable input UVLO threshold (VEN_H ~1.2 V).
4 SS/TR passive Soft-start and tracking pin. An external capacitor sets the output voltage rise time via a 2.6 µA charge current. The voltage on this pin overrides the internal 0.8 V reference, enabling tracking/sequencing.
5 RT/CLK bidirectional Sets the internal oscillator frequency (100 kHz to 1.2 MHz) via a resistor to GND, or accepts an external clock for PLL synchronization (100 kHz to 1.2 MHz). Reverts to resistor-programmed frequency if the external clock stops.
6 PWRGD output Open-drain power-good output. Asserts low on thermal shutdown, dropout, over-voltage, or EN shutdown. VPG_LOW ≤ 0.1 V at 1 mA sink; leakage ≤ 200 nA at 5 V pull-up. Trips at ~90%/110% of VFB.
7 FB input Inverting input of the trans-conductance error amplifier. Connect the tap of an external feedback resistor divider from VOUT to GND; regulated to VREF = 0.8 V (typ, ±1%).
8 COMP output Error amplifier output. Connect an external frequency loop compensation network (typ R-C to GND). Trans-conductance Gm = 240 µA/V; clamps at 0.47 V (low) / 2.25 V (high).
9 GND power_in Device ground. Should be tied to the thermal pad and to the PCB ground plane for proper operation.
10 SW power_out Regulator switching node - drain of the internal high-side MOSFET (RDSON = 220 mΩ typ). Connect to the external power inductor. Abs max -1 V to 65 V (-5 V for 10 ns transient). Peak current limit ~4.2 A.
11 PAD power_in Exposed thermal pad, heat dissipation path of the die. Electrically connected to GND (pin 9). Must be soldered to the PCB ground plane for proper operation and optimized thermal performance (θJA = 62.5 °C/W).

Key specifications

Parameter Value
Manufacturer SCT
Package MSOP-10-EP
Category PMIC
Pins 11

Ordering variants

Same part, different packaging or reel option.

  • SCT2620MRER

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage (VIN, EN pins) VIN, EN -0.3 65 V 2
BOOT pin voltage BOOT -0.3 72 V 2
SW pin voltage SW -1 65 V 2
SW pin 10-ns transient voltage SW, 10-ns transient -5 65 V 10-ns transient 2
BOOT-SW voltage BOOT-SW -0.3 6 V 2
COMP, FB, RT/CLK, SS, PWRGD voltage COMP, FB, RT/CLK, SS, PWRGD -0.3 6 V 2
Operating junction temperature TJ -40 150 °C 2
Storage temperature TSTG -65 150 °C 2
Input voltage range VIN 3.8 60 V Over operating free-air temperature range 3
Output voltage range VOUT 0.8 57 V Over operating free-air temperature range 3
Operating junction temperature TJ -40 150 °C Over operating free-air temperature range 3
Junction-to-ambient thermal resistance θja 62.5 °C/W standard board 3
Junction-to-case (top) thermal resistance θjctop 83 °C/W 3
Junction-to-top characterization parameter ψjt 5.9 °C/W 3
Operating input voltage VIN 3.8 60 V 3
Input UVLO threshold (VIN rising) VIN_UVLO 3.5 V VIN rising 3
Input UVLO hysteresis 400 mV 3
Shutdown current from VIN pin ISHDN 2 5 μA EN=0, no load 3
Quiescent current from VIN pin IQ 190 μA EN floating, no load, non-switching, BOOT-SW=5V, RRT=200 kΩ, FB=2V 3
High-side MOSFET on-resistance RDSON_H 220 mΩ VBOOT-VSW=5V 4
Reference voltage of FB VREF 0.792 0.8 0.808 V 4
Error amplifier trans-conductance GEA 240 μA/V -2μA<ICOMP<2μA, VCOMP=1V 4
EA maximum source current ICOMP_SRC 30 μA VFB=VREF-100mV, VCOMP=1V 4
EA maximum sink current ICOMP_SNK 30 μA VFB=VREF+100mV, VCOMP=1V 4
COMP high clamp VCOMP_H 2.25 V 4
COMP low clamp VCOMP_L 0.47 V 4
High-side power MOSFET peak current limit threshold ILIM_HS 3.6 4.2 4.8 A 4
Enable high threshold VEN_H 1.2 V 4
Enable low threshold VEN_L 1.05 V 4
Enable pin pull-up current IEN_L 1 μA EN=1V 4
Enable pin pull-up current IEN_H 4 uA EN=1.5V 4
Charge current ISS 2.6 uA 4
Frequency range using RT mode FRANGE_RT 100 1200 kHz using RT mode 4
Switching frequency FSW 450 500 550 kHz RRT=200 kΩ(1%) 4
Frequency range using CLK mode FRANGE_CLK 100 1200 kHz using CLK mode 4
Minimum on-time tON_MIN 100 ns VIN=24V 4
Power-good flag under voltage tripping threshold (power good) VPG_UV 95 % POWER GOOD (% of FB voltage) 4
Power-good flag under voltage tripping threshold (power bad) VPG_UV 90 % POWER BAD (% of FB voltage) 4
Power-good flag over voltage tripping threshold (power bad) VPG_OV 110 % POWER BAD (% of FB voltage) 4
Power-good flag over voltage tripping threshold (power good) VPG_OV 105 % POWER GOOD (% of FB voltage) 4
PWRGD leakage current at high level output IPG 200 nA VPull-Up = 5V 4
PWRGD low level output voltage VPG_LOW 0.1 V IPull-Up = 1 mA 4
Feedback overvoltage threshold (rising) VOVP 110 % VFB/VREF rising 4
Feedback overvoltage threshold (falling) VOVP 105 % VFB/VREF falling 4
BOOT UVLO reference voltage VBOOTUV 2.5 V BOOT-SW falling 4
BOOT UVLO hysteresis 230 mV 4
Thermal shutdown threshold TSD 172 °C TJ rising 4
Thermal shutdown hysteresis 12 °C 4

CAD (KiCad official)

  • Symbol: SCT2620MRER
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: sct2620mrer-etched.step / sct2620mrer-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sct2620mrer.step / sct2620mrer.glb are the bare package body.

3D model downloads

Two STEP files. Same geometry, different body top:

File Size Use it when
sct2620mrer.step 151 KB You want the bare part, or you mark your own boards.
sct2620mrer-etched.step 2.6 MB You want the part with SCT2620MRER already on it.

The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 634 faces against 182 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SCT datasheet (22 pp, sha256 143e0877463556e0, retrieved 2026-08-17, tier: lcsc)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF