main
Ray
sct2452ster: specified limits as data (metadata.characteristics, 26 rows from the datasheet)
dee43ee
SCT2452STER
SCT · DC-DC Converters · ESOP-8
SCT2452STER from SCT, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_in | Bootstrap supply for high-side power MOSFET gate driver. Connect a 0.1µF capacitor between BOOT and SW; the bootstrap cap is charged when the low-side MOSFET is on or SW is low. BOOT-SW UVLO threshold ≈ 2.36V. |
| 2 | VIN | power_in | Input supply voltage, 3.8V to 36V (42V transient max). Connect a local high-frequency bypass capacitor from VIN to GND as close as possible to the pin. |
| 3 | EN | input | Enable input with internal pull-up current source (~1.5µA at 1V). Pull below 1.1V to disable the converter; float or tie to VIN to enable. A VIN-to-GND resistor divider on EN sets a programmable input UVLO threshold (VEN_H ≈ 1.18V). |
| 4 | RT/CLK | bidirectional | Sets internal oscillator frequency or accepts an external clock. Resistor to GND programs Fsw from 100kHz to 1.1MHz (e.g. 200kΩ ≈ 500kHz); alternatively drive with an external clock (100kHz-1.1MHz) for PLL synchronization. Reverts to resistor-programmed frequency if the external clock stops. |
| 5 | FB | input | Inverting input of the transconductance error amplifier. Connect a resistor divider from VOUT to FB to GND; the loop regulates FB to VREF = 0.8V (typ, ±1%). Overvoltage protection trips at ~110% of VREF. |
| 6 | SS | passive | Soft-start programming pin. Connect a capacitor from SS to GND; internal ~3µA source current charges it to set the output voltage ramp time. |
| 7 | GND | power_in | Device ground. Common return for input bypass, output feedback, and control-circuit references. |
| 8 | SW | power_out | Switch node - regulator switching output. Connect to the external power inductor. Absolute range -1V to 38V; also the bootstrap capacitor return for the high-side driver. |
| 9 | Thermal Pad | power_in | Exposed thermal pad on the ESOP-8 package. Electrically connected to GND (pin 7). Must be soldered to the PCB ground plane for proper thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SCT |
| Package | ESOP-8 |
| Category | PMIC |
| Pins | 9 |
Ordering variants
Same part, different packaging or reel option.
SCT2452STER
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Input voltage range | VIN | 3.8 | 36 | V | 3 | ||
| VOUT Output voltage range | VOUT | 0.8 | 36 | V | 3 | ||
| TJ Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| VIN | VIN | -0.3 | 38 | V | 2 | ||
| VIN Transient (300ms) | VIN Transient (300ms) | -0.3 | 42 | V | 2 | ||
| EN | EN | -0.3 | 38 | V | 2 | ||
| BOOT | BOOT | -0.3 | 44 | V | 2 | ||
| SW | SW | -1 | 38 | V | 2 | ||
| BOOT-SW | BOOT-SW | -0.3 | 6 | V | 2 | ||
| SS, FB, RT/CLK | SS, FB, RT/CLK | -0.3 | 6 | V | 2 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 2 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 2 | ||
| Junction to ambient thermal resistance (SOP-8L) | RθJA | 42 | °C/W | 3 | |||
| Junction to case thermal resistance (SOP-8L) | RθJC | 45.8 | °C/W | 3 | |||
| Operating input voltage | VIN | 3.8 | 36 | V | 4 | ||
| Input UVLO Threshold | VIN_UVLO | 3.5 | 3.7 | V | VIN rising | 4 | |
| Shutdown current from VIN pin | ISHDN | 1 | 3 | μA | EN=0, no load | 4 | |
| Reference voltage of FB | VREF | 0.792 | 0.8 | 0.808 | V | 4 | |
| High-side power MOSFET peak current limit threshold | ILIM_HS | 6.8 | 8 | 9.2 | A | 4 | |
| Enable high threshold | VEN_H | 1.18 | 1.25 | V | 4 | ||
| Enable low threshold | VEN_L | 1.03 | 1.1 | V | 4 | ||
| Enable pin pull-up current | IEN_L | 1 | 1.5 | 2 | μA | EN=1V | 4 |
| Frequency range using RT mode | FRANGE_RT | 100 | 1100 | kHz | 4 | ||
| Switching frequency | FSW | 450 | 500 | 550 | kHz | RRT=200 kΩ(1%) | 4 |
| Frequency range using CLK mode | FRANGE_CLK | 100 | 1100 | kHz | 4 | ||
| Frequency spread spectrum in percentage of Fsw | FJITTER | -6 | 6 | % | 4 |
CAD (KiCad official)
- Symbol:
SCT2452STER - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
sct2452ster-etched.step/sct2452ster-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sct2452ster.step/sct2452ster.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SCT datasheet (22 pp, sha256
a97363c67f20b5f7, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SCT2452STER
**SCT** · DC-DC Converters · ESOP-8
SCT2452STER from SCT, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_in | Bootstrap supply for high-side power MOSFET gate driver. Connect a 0.1µF capacitor between BOOT and SW; the bootstrap cap is charged when the low-side MOSFET is on or SW is low. BOOT-SW UVLO threshold ≈ 2.36V. |
| 2 | VIN | power_in | Input supply voltage, 3.8V to 36V (42V transient max). Connect a local high-frequency bypass capacitor from VIN to GND as close as possible to the pin. |
| 3 | EN | input | Enable input with internal pull-up current source (~1.5µA at 1V). Pull below 1.1V to disable the converter; float or tie to VIN to enable. A VIN-to-GND resistor divider on EN sets a programmable input UVLO threshold (VEN_H ≈ 1.18V). |
| 4 | RT/CLK | bidirectional | Sets internal oscillator frequency or accepts an external clock. Resistor to GND programs Fsw from 100kHz to 1.1MHz (e.g. 200kΩ ≈ 500kHz); alternatively drive with an external clock (100kHz-1.1MHz) for PLL synchronization. Reverts to resistor-programmed frequency if the external clock stops. |
| 5 | FB | input | Inverting input of the transconductance error amplifier. Connect a resistor divider from VOUT to FB to GND; the loop regulates FB to VREF = 0.8V (typ, ±1%). Overvoltage protection trips at ~110% of VREF. |
| 6 | SS | passive | Soft-start programming pin. Connect a capacitor from SS to GND; internal ~3µA source current charges it to set the output voltage ramp time. |
| 7 | GND | power_in | Device ground. Common return for input bypass, output feedback, and control-circuit references. |
| 8 | SW | power_out | Switch node - regulator switching output. Connect to the external power inductor. Absolute range -1V to 38V; also the bootstrap capacitor return for the high-side driver. |
| 9 | Thermal Pad | power_in | Exposed thermal pad on the ESOP-8 package. Electrically connected to GND (pin 7). Must be soldered to the PCB ground plane for proper thermal performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SCT |
| Package | ESOP-8 |
| Category | PMIC |
| Pins | 9 |
## Ordering variants
Same part, different packaging or reel option.
- `SCT2452STER`
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Input voltage range | VIN | 3.8 | | 36 | V | | 3 |
| VOUT Output voltage range | VOUT | 0.8 | | 36 | V | | 3 |
| TJ Operating junction temperature | TJ | -40 | | 125 | °C | | 3 |
| VIN | VIN | -0.3 | | 38 | V | | 2 |
| VIN Transient (300ms) | VIN Transient (300ms) | -0.3 | | 42 | V | | 2 |
| EN | EN | -0.3 | | 38 | V | | 2 |
| BOOT | BOOT | -0.3 | | 44 | V | | 2 |
| SW | SW | -1 | | 38 | V | | 2 |
| BOOT-SW | BOOT-SW | -0.3 | | 6 | V | | 2 |
| SS, FB, RT/CLK | SS, FB, RT/CLK | -0.3 | | 6 | V | | 2 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 2 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 2 |
| Junction to ambient thermal resistance (SOP-8L) | RθJA | | 42 | | °C/W | | 3 |
| Junction to case thermal resistance (SOP-8L) | RθJC | | 45.8 | | °C/W | | 3 |
| Operating input voltage | VIN | 3.8 | | 36 | V | | 4 |
| Input UVLO Threshold | VIN_UVLO | 3.5 | | 3.7 | V | VIN rising | 4 |
| Shutdown current from VIN pin | ISHDN | | 1 | 3 | μA | EN=0, no load | 4 |
| Reference voltage of FB | VREF | 0.792 | 0.8 | 0.808 | V | | 4 |
| High-side power MOSFET peak current limit threshold | ILIM_HS | 6.8 | 8 | 9.2 | A | | 4 |
| Enable high threshold | VEN_H | 1.18 | | 1.25 | V | | 4 |
| Enable low threshold | VEN_L | 1.03 | | 1.1 | V | | 4 |
| Enable pin pull-up current | IEN_L | 1 | 1.5 | 2 | μA | EN=1V | 4 |
| Frequency range using RT mode | FRANGE_RT | 100 | | 1100 | kHz | | 4 |
| Switching frequency | FSW | 450 | 500 | 550 | kHz | RRT=200 kΩ(1%) | 4 |
| Frequency range using CLK mode | FRANGE_CLK | 100 | | 1100 | kHz | | 4 |
| Frequency spread spectrum in percentage of Fsw | FJITTER | -6 | | 6 | % | | 4 |
## CAD (KiCad official)
- Symbol: `SCT2452STER`
- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm`
- 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files: `sct2452ster-etched.step` / `sct2452ster-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sct2452ster.step` / `sct2452ster.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [SCT datasheet](docs/sct2452ster-datasheet.pdf) (22 pp, sha256 `a97363c67f20b5f7`, retrieved 2026-08-17, tier: lcsc)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/sct2452ster-datasheet.pdf)