Generated by kicad-footprint-generator · KiCad file format 20260206
SCT2420STER
SCT · DC-DC Converters · ESOP-8
SCT2420STER from SCT, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_in | Power supply bias for the high-side power MOSFET gate driver. Connect a 0.1µF bootstrap capacitor from BOOT to SW. The capacitor is charged when the low-side MOSFET is on or SW voltage is low. Absolute max rating -0.3V to 46V; BOOT-SW max 6V. |
| 2 | VIN | power_in | Input supply voltage, 3.8V to 40V operating range (absolute max 42V). Connect a local high-frequency bypass capacitor from VIN to GND as close as possible. |
| 3 | EN | input | Enable pin with internal pull-up current source (1.5µA at 1V, 5.5µA at 1.5V). Pull below 1.1V to disable the converter; float or connect to VIN to enable. A resistor divider from VIN to GND on EN sets the input voltage lockout threshold. Enable high threshold typ. 1.18V. |
| 4 | RT/CLK | bidirectional | Sets the internal oscillator clock frequency or synchronizes to an external clock. Connect a resistor from this pin to ground to set switching frequency (100kHz to 2.2MHz; 200kΩ ≈ 500kHz). Alternatively drive with an external clock (100kHz-2.2MHz) for PLL synchronization; automatically reverts to resistor-programmed frequency if clock stops. |
| 5 | FB | input | Inverting input of the trans-conductance error amplifier. External feedback resistor divider from VOUT to GND sets the output voltage; device regulates FB to the internal 0.8V (±1%) reference. |
| 6 | COMP | output | Error amplifier output. Connect to the frequency loop compensation network (typically an R-C to GND). COMP high clamp 3V, low clamp 0.4V; EA transconductance 300µS. |
| 7 | GND | power_in | Device ground return. Tie to system ground plane along with the thermal pad. |
| 8 | SW | output | Regulator switching node. Connect to an external power inductor. Absolute max rating -0.3V to 42V. |
| 9 | Thermal Pad | passive | Exposed thermal pad on package underside - heat dissipation path from the die. Must be electrically connected to the GND pin and soldered to the PCB ground plane for proper operation and optimal thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SCT |
| Package | ESOP-8 |
| Category | PMIC |
| Pins | 9 |
Ordering variants
Same part, different packaging or reel option.
SCT2420STER
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN input voltage (absolute maximum) | VIN, EN | -0.3 | 42 | V | Over operating free-air temperature unless otherwise noted | 2 | |
| BOOT voltage (absolute maximum) | BOOT | -0.3 | 46 | V | Over operating free-air temperature unless otherwise noted | 2 | |
| SW voltage (absolute maximum) | SW | -0.3 | 42 | V | Over operating free-air temperature unless otherwise noted | 2 | |
| BOOT-SW voltage (absolute maximum) | BOOT-SW | -0.3 | 6 | V | Over operating free-air temperature unless otherwise noted | 2 | |
| COMP, FB, RT/CLK voltage (absolute maximum) | COMP, FB, RT/CLK | -0.3 | 6 | V | Over operating free-air temperature unless otherwise noted | 2 | |
| Operating junction temperature (absolute maximum) | TJ | -40 | 150 | °C | Over operating free-air temperature unless otherwise noted | 2 | |
| Storage temperature | TSTG | -65 | 150 | °C | Over operating free-air temperature unless otherwise noted | 2 | |
| Input voltage range (recommended) | VIN | 3.8 | 40 | V | Over operating free-air temperature range unless otherwise noted | 3 | |
| Output voltage range (recommended) | VOUT | 0.8 | 40 | V | Over operating free-air temperature range unless otherwise noted | 3 | |
| Operating junction temperature (recommended) | TJ | -40 | 125 | °C | Over operating free-air temperature range unless otherwise noted | 3 | |
| Operating input voltage | VIN | 3.8 | 40 | V | 3 | ||
| Input UVLO threshold | VIN_UVLO | 3.5 | 3.7 | V | VIN rising | 3 | |
| Shutdown current from VIN pin | ISHDN | 1 | 3 | μA | EN=0, no load | 3 | |
| Reference voltage of FB | VREF | 0.792 | 0.8 | 0.808 | V | 4 | |
| Enable high threshold | VEN_H | 1.18 | 1.25 | V | 4 | ||
| Enable low threshold | VEN_L | 1.03 | 1.1 | V | 4 | ||
| Enable pin pull-up current | IEN_L | 1 | 1.5 | 2 | μA | EN=1V | 4 |
| Frequency range using RT mode | FRANGE_RT | 100 | 2200 | kHz | 4 | ||
| Switching frequency | FSW | 450 | 500 | 550 | kHz | RRT=200 kΩ(1%) | 4 |
| Frequency range using CLK mode | FRANGE_CLK | 100 | 2200 | kHz | 4 | ||
| Frequency spread spectrum in percentage of Fsw | FJITTER | -6 | 6 | % | 4 | ||
| Input UVLO hysteresis | 400 | mV | 3 | ||||
| Quiescent current from VIN pin | IQ | 25 | μA | EN floating, no load, non-switching, BOOT-SW=5V | 3 | ||
| High-side MOSFET on-resistance | RDSON_H | 160 | mΩ | VBOOT-VSW=5V | 3 | ||
| Low-side MOSFET on-resistance | RDSON_L | 80 | mΩ | 3 | |||
| Error amplifier trans-conductance | GEA | 300 | μS | -2μA<ICOMP<2μA, VCOMP=1V | 4 | ||
| EA maximum source current | ICOMP_SRC | 30 | μA | VFB=VREF-100mV, VCOMP=1V | 4 | ||
| EA maximum sink current | ICOMP_SNK | 30 | μA | VFB=VREF+100mV, VCOMP=1V | 4 | ||
| COMP high clamp | VCOMP_H | 3 | V | 4 | |||
| COMP low clamp | VCOMP_L | 0.4 | V | 4 | |||
| High-side power MOSFET peak current limit threshold | ILIM_HS | 3 | A | 4 | |||
| Low-side power MOSFET sourcing current limit threshold | ILIM_LSSRC | 3.2 | A | 4 | |||
| Over current protection hiccup wait time | THIC_W | 512 | cycles | 4 | |||
| Over current protection hiccup restart time | THIC_R | 8192 | cycles | 4 | |||
| Enable pin pull-up current | IEN_H | 5.5 | uA | EN=1.5V | 4 | ||
| Internal soft start time | Tss | 2 | ms | 4 | |||
| Minimum on-time | tON_MIN | 80 | ns | VIN=24V | 4 | ||
| Feedback overvoltage with respect to VFB/VREF, rising | VOVP | 110 | % | VFB/VREF rising | 4 | ||
| Feedback overvoltage with respect to VFB/VREF, falling | VOVP | 105 | % | VFB/VREF falling | 4 | ||
| BOOT-SW UVLO threshold | VBOOTUV | 2.36 | V | BOOT-SW falling | 4 | ||
| BOOT-SW UVLO hysteresis | 300 | mV | 4 | ||||
| Thermal shutdown threshold | TSD | 170 | °C | TJ rising | 4 | ||
| Thermal shutdown hysteresis | 25 | °C | 4 | ||||
| Junction to ambient thermal resistance (SOP-8L) | RθJA | 42 | °C/W | 3 | |||
| Junction to case thermal resistance (SOP-8L) | RθJC | 45.8 | °C/W | 3 |
CAD (KiCad official)
- Symbol:
SCT2420STER - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
sct2420ster-etched.step/sct2420ster-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sct2420ster.step/sct2420ster.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SCT datasheet (22 pp, sha256
dbaa901660a31b92, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).