Generated by kicad-footprint-generator · KiCad file format 20260206
SAK-XC2224L-20F66V AA
Infineon Technologies · Infineon · VQFN-48-EP(7x7)
SAK-XC2224L-20F66V AA from Infineon Technologies, in a VQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TESTM | input | Testmode enable pin that must be held HIGH (connected to VDDPB) for normal operation, with an internal pull-up holding it high when undriven. |
| 2 | TRST | input | Test-system reset input that must be held low for normal operation, with an internal pull-down holding it low when undriven; a high level at the rising edge of PORST activates the debug system. |
| 3 | P6.3 | bidirectional | Bit 3 of Port 6, general-purpose I/O on a standard pad in domain B, with alternate functions including CCU63 channel 2 output and GPT12E timer T3 toggle latch output. |
| 4 | P6.1 | bidirectional | Bit 1 of Port 6, general-purpose I/O on a digital/analog pad in domain B, which also serves as ADC0 analog input channel 17 and external analog MUX control output 1. |
| 5 | P6.0 | bidirectional | Bit 0 of Port 6, general-purpose I/O on a digital/analog pad in domain B, which also serves as ADC0 analog input channel 16 and external analog MUX control output 0. |
| 6 | VSS | power_in | Digital ground that must be connected to the ground line or ground plane. |
| 7 | VDDPB | power_in | Digital pad supply voltage for domain B, with decoupling capacitors connected to adjacent VDDP/VSS pin pairs as close as possible to the pins. |
| 8 | VAREF | power_in | Reference voltage for the ADC0 A/D converter. |
| 9 | VAGND | power_in | Reference ground for the ADC0 A/D converter. |
| 10 | P5.0 | input | Bit 0 of Port 5, general-purpose input-only pad, also ADC0 analog input channel 0. |
| 11 | P5.2 | input | Bit 2 of Port 5, general-purpose input-only pad, also ADC0 analog input channel 2 and JTAG test data input TDI_A. |
| 12 | P5.3 | input | Bit 3 of Port 5, general-purpose input-only pad, also ADC0 analog input channel 3 and GPT12E timer T3 count/gate input. |
| 13 | P5.4 | input | Bit 4 of Port 5, general-purpose input-only pad, also ADC0 analog input channel 4 and JTAG test mode selection input TMS_A. |
| 14 | P5.8 | input | Bit 8 of Port 5, general-purpose input-only pad, also ADC0 analog input channel 8 and external run control input for CCU6x T12. |
| 15 | P5.9 | input | Bit 9 of Port 5, general-purpose input-only pad, also ADC0 analog input channel 9 and CC2 timer T7 count input. |
| 16 | P2.0 | bidirectional | Bit 0 of Port 2, general-purpose I/O on a digital/analog pad in domain B, also ADC0 analog input channel 19 and CAN node 0 receive data input. |
| 17 | P2.1 | bidirectional | Bit 1 of Port 2, general-purpose I/O on a digital/analog pad in domain B, also CAN node 0 transmit data output and ADC0 analog input channel 20. |
| 18 | VDDIM | power_in | Digital core supply voltage for domain M that must be decoupled with a ceramic capacitor, and all VDDIM pins must be connected to each other. |
| 19 | VSS | power_in | Digital ground that must be connected to the ground line or ground plane. |
| 20 | VDDPB | power_in | Digital pad supply voltage for domain B, with decoupling capacitors connected to adjacent VDDP/VSS pin pairs as close as possible to the pins. |
| 21 | P2.2 | bidirectional | Bit 2 of Port 2, general-purpose I/O on a standard pad, also CAN node 1 transmit data output and ERU channel 1 input A0. |
| 22 | P2.3 | bidirectional | Bit 3 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 0 shift data output and CAN node 0 receive data input. |
| 23 | P2.4 | bidirectional | Bit 4 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 1 shift data output and CAN node 0 transmit data output. |
| 24 | P2.5 | bidirectional | Bit 5 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 0 shift clock output and CAN node 0 transmit data output. |
| 25 | P2.6 | bidirectional | Bit 6 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 0 select/control 0 output and clock signal input CLKIN1. |
| 26 | P2.7 | bidirectional | Bit 7 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 1 select/control 0 output and CAN node 1 receive data input. |
| 27 | P2.8 | bidirectional | Bit 8 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 1 shift clock output and programmable clock output EXTCLK. |
| 28 | P2.9 | bidirectional | Bit 9 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 1 shift data output, CAN node 1 transmit data output and configuration pin C1. |
| 29 | P2.10 | bidirectional | Bit 10 of Port 2, general-purpose I/O on a standard pad, also USIC0 channel 1 shift data output and GPT12E CAPREL capture input CAPINA. |
| 30 | P2.13 | bidirectional | Bit 13 of Port 2, general-purpose I/O on a standard pad, also USIC1 channel 1 shift data output and CCU63 channel 0 output. |
| 31 | P10.0 | bidirectional | Bit 0 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 1 shift data output, CCU60 channel 0 output and CCU60 channel 0 input. |
| 32 | P10.1 | bidirectional | Bit 1 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 0 shift data output, CCU60 channel 1 output and CCU60 channel 1 input. |
| 33 | P10.2 | bidirectional | Bit 2 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 0 shift clock output, CCU60 channel 2 output and CCU60 channel 2 input. |
| 34 | P10.3 | bidirectional | Bit 3 of Port 10, general-purpose I/O on a standard pad, also CCU60 channel 0 output, USIC0 shift control input and CAN node 1 receive data input. |
| 35 | P10.4 | bidirectional | Bit 4 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 0 select/control 3 output, CCU60 channel 1 output and ESR1 trigger input 9. |
| 36 | P10.5 | bidirectional | Bit 5 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 1 shift clock output and CCU60 channel 2 output. |
| 37 | P10.6 | bidirectional | Bit 6 of Port 10, general-purpose I/O on a standard pad, also USIC1 channel 0 shift data output and the CCU60/CCU63 emergency trap input. |
| 38 | P10.7 | bidirectional | Bit 7 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 1 shift data output, CCU60 channel 3 output and GPT12E timer T4 count/gate input. |
| 39 | P10.8 | bidirectional | Bit 8 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 0 master clock output, OCDS break signal input BRKIN_B and GPT12E timer T3 external up/down input. |
| 40 | P10.9 | bidirectional | Bit 9 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 0 select/control 4 output, CAN node 1 transmit data output and DAP0/JTAG clock input TCK_B. |
| 41 | VDDPB | power_in | Digital pad supply voltage for domain B, with decoupling capacitors connected to adjacent VDDP/VSS pin pairs as close as possible to the pins. |
| 42 | VSS | power_in | Digital ground that must be connected to the ground line or ground plane. |
| 43 | VDDIM | power_in | Digital core supply voltage for domain M that must be decoupled with a ceramic capacitor, and all VDDIM pins must be connected to each other. |
| 44 | P10.10 | bidirectional | Bit 10 of Port 10, general-purpose I/O on a standard pad, also USIC0 channel 0 select/control 0 output, CCU60 channel 3 output and JTAG test data input TDI_B. |
| 45 | P10.12 | bidirectional | Bit 12 of Port 10, general-purpose I/O on a standard pad, also DAP1/JTAG test data output TDO_A, SPD input/output and configuration pin C0. |
| 46 | XTAL2 | output | Crystal oscillator amplifier output, in the special/MP domain M pad class. |
| 47 | XTAL1 | input | Crystal oscillator amplifier input; to clock the device from an external source, drive XTAL1 while leaving XTAL2 unconnected, and voltages on XTAL1 must comply with VDDIM. |
| 48 | PORST | input | Power-on reset input where a low level resets the device completely; a spike filter suppresses pulses below 10 ns, pulses above 100 ns pass, and the minimum duration for safe recognition is 120 ns, with an internal pull-up. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | VQFN-48-EP(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output current on a pin when high value is driven | IOH | -15 | mA | 58 | |||
| Output current on a pin when low value is driven | IOL | 15 | mA | 58 | |||
| Overload current | IOV | -5 | 5 | mA | 58 | ||
| Absolute sum of overload currents | Σ/IOV/ | 50 | mA | 58 | |||
| Junction Temperature | TJ | -40 | 150 | °C | 58 | ||
| Storage Temperature | TST | -65 | 150 | °C | 58 | ||
| Digital supply voltage for IO pads and voltage regulators | VDDP | -0.5 | 6 | V | 58 | ||
| Voltage on any pin with respect to ground (Vss) | VIN | -0.5 | V | VIN≤ VDDP(max) | 58 | ||
| Voltage Regulator Buffer Capacitance for DMP_M | CEVRM | 1 | 4.7 | μF | 59 | ||
| System frequency (66 MHz device) | fSYS | 66 | MHz | 59 | |||
| Overload current for analog inputs | IOVA | -2 | 5 | mA | not subject to production test | 59 | |
| Overload current for digital inputs | IOVD | -5 | 5 | mA | not subject to production test | 59 | |
| Absolute sum of overload currents | Σ/IOV/ | 30 | mA | not subject to production test | 60 | ||
| Digital supply voltage for IO pads and voltage regulators | VDDP | 3 | 5.5 | V | 60 | ||
| Upper voltage range definition: digital supply voltage | VDDP | 4.5 | 5 | 5.5 | V | 61 | |
| Lower voltage range definition: digital supply voltage | VDDP | 3 | 3.3 | 4.5 | V | 61 | |
| Pin capacitance (digital inputs/outputs) | CIO | 10 | pF | not subject to production test | 64 | ||
| Absolute input leakage current on pins of analog ports | /IOZ1/ | 10 | 200 | nA | VIN> VSS ; VIN< VDDP | 64 | |
| Absolute input leakage current for all other pins | /IOZ2/ | 0.2 | 5 | μA | TJ≤ 110 °C; VIN> VSS ; VIN< VDDP | 64 | |
| Absolute input leakage current for all other pins | /IOZ2/ | 0.2 | 10 | μA | TJ≤ 150 °C; VIN> VSS ; VIN< VDDP | 64 | |
| Pull Level Force Current | /IPLF/ | 220 | μA | VIN≥ VIHmin (pulldown_enabled); VIN≤ VILmax (pullup_enabled) | 64 | ||
| Pull Level Keep Current | /IPLK/ | 30 | μA | VIN≥ VIHmin (pullup_enabled); VIN≤ VILmax (pulldown_enabled) | 64 | ||
| Input low voltage (all except XTAL1) | VIL | -0.3 | V | 65 | |||
| Output Low Voltage | VOL | 0.4 | V | IOL≤ IOLnom | 65 | ||
| Output Low Voltage | VOL | 1 | V | IOL≤ IOLmax | 65 | ||
| Absolute input leakage current for all other pins | /IOZ2/ | 0.2 | 2 | μA | TJ≤ 110 °C; VIN> VSS ; VIN< VDDP | 66 | |
| Absolute input leakage current for all other pins | /IOZ2/ | 0.2 | 6 | μA | TJ≤ 150 °C; VIN> VSS ; VIN< VDDP | 66 | |
| Pull Level Force Current | /IPLF/ | 150 | μA | VIN≥ VIHmin (pulldown_enabled); VIN≤ VILmax (pullup_enabled) | 66 | ||
| Pull Level Keep Current | /IPLK/ | 10 | μA | VIN≥ VIHmin (pullup_enabled); VIN≤ VILmax (pulldown_enabled) | 66 | ||
| Output Low Voltage | VOL | 0.4 | V | IOL≤ IOLnom | 67 | ||
| Output Low Voltage | VOL | 1 | V | IOL≤ IOLmax | 67 | ||
| Power supply current in stopover mode, EVVRs on | ISSO | 0.7 | 2 | mA | power_mode=stopover ; voltage_range=both | 69 | |
| Leakage supply current | ILK1 | 0.03 | 0.04 | mA | TJ= 25 °C | 70 | |
| Leakage supply current | ILK1 | 0.4 | 1.1 | mA | TJ= 85 °C | 70 | |
| Leakage supply current | ILK1 | 1.7 | 4.9 | mA | TJ= 125 °C | 70 | |
| Leakage supply current | ILK1 | 3.5 | 10.7 | mA | TJ= 150 °C | 70 | |
| Switched capacitance at an analog input | CAINSW | 9 | 20 | pF | not subject to production test | 72 | |
| Total capacitance at an analog input | CAINT | 20 | 30 | pF | not subject to production test | 72 | |
| Switched capacitance at the reference input | CAREFSW | 15 | 30 | pF | not subject to production test | 72 | |
| Total capacitance at the reference input | CAREFT | 20 | 40 | pF | not subject to production test | 72 | |
| Internal clock source frequency | fINT | 4.8 | 5 | 5.2 | MHz | 78 | |
| Short-term deviation of internal clock source frequency | ΔfINT | -1 | 1 | % | ΔTJ = ≤ 10°C | 78 | |
| Wakeup clock source frequency | fWU | 400 | 700 | kHz | FREQSEL= 00 | 78 | |
| Wakeup clock source frequency | fWU | 210 | 390 | kHz | FREQSEL= 01 | 78 | |
| Wakeup clock source frequency | fWU | 140 | 260 | kHz | FREQSEL= 10 | 78 | |
| Wakeup clock source frequency | fWU | 110 | 200 | kHz | FREQSEL= 11 | 78 | |
| Startup time from power-on with code execution from Flash | tSPO | 1.4 | 1.9 | 2.4 | ms | fWU = 500 kHz | 78 |
| Thermal resistance Junction-Ambient | RΘJA | 73 | K/W | No thermal via, 2-layer | 105 | ||
| Thermal resistance Junction-Ambient | RΘJA | 49 | K/W | No thermal via, 4-layer | 105 | ||
| Thermal resistance Junction-Ambient | RΘJA | 43 | K/W | 4-layer, no pad | 105 | ||
| Thermal resistance Junction-Ambient | RΘJA | 34 | K/W | 4-layer, pad | 105 | ||
| Power Dissipation | PDISS | 0.7 | W | 105 | |||
| Oscillator frequency | fOSC | 4 | 40 | MHz | Input= Clock Signal | 89 | |
| Oscillator frequency | fOSC | 4 | 16 | MHz | Input= Crystal or Resonator | 89 |
CAD (KiCad official)
- Symbol:
SAK-XC2224L-20F66V AA - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: VQFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
sak-xc2224l-20f66v-aa-etched.step/sak-xc2224l-20f66v-aa-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sak-xc2224l-20f66v-aa.step/sak-xc2224l-20f66v-aa.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (109 pp, sha256
1977d9d787a44bf2, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).