main
Ray Publish 0.1.0 e95318b

S25FS512SAGMFI011

Cypress Semicon · NOR FLASH · SOIC-16-300mil

S25FS512SAGMFI011 from Cypress Semicon, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IO3/RESET# bidirectional Quad I/O data line IO3 or hardware RESET# input, with an internal pull-up so it may be left unconnected if quad mode and hardware reset are not in use.
2 VCC power_in Core and I/O supply voltage for the 1.8 V S25FS512S device.
3 RFU unconnected Reserved for future use.
4 NC unconnected Not connected internally.
5 DNU unconnected Do not use.
6 RFU unconnected Reserved for future use.
7 CS# input Chip select input that enables the device when driven low.
8 SO/IO1 bidirectional Serial data output in single mode or IO1 in dual and quad modes.
9 WP#/IO2 bidirectional Write protect input or IO2 in quad mode.
10 VSS power_in Supply and signal ground.
11 DNU unconnected Do not use.
12 NC unconnected Not connected internally.
13 DNU unconnected Do not use.
14 RFU unconnected Reserved for future use.
15 SI/IO0 bidirectional Serial data input in single mode or IO0 in dual and quad modes.
16 SCK input Serial clock input.

Key specifications

Parameter Value
Manufacturer Cypress Semicon
Package SOIC-16-300mil
Category Memory
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC VCC 1.7 2 V Operating range, Industrial (I) grade 23
Ambient temperature, Industrial (I) TA -40 85 °C Industrial (I) grade, ordering code MFI, -40 °C to +85 °C 23
Supply voltage with respect to ground VCC -0.5 2.5 V 23
Output short circuit current 100 mA No more than one output shorted to ground at a time; duration not greater than one second (note 10) 23
Storage temperature TSTORE -65 150 °C Plastic packages 23
Ambient temperature with power applied TA -65 150 °C Power applied 23
VCC current (latchup) -100 100 mA Latchup specification 23
Minimum operation voltage VCC(min) 1.7 V VCC(minimum operation voltage) 24
Cut-off voltage for re-initialization VCC(cut-off) 1.5 V VCC (Cut-off where re-initialization is needed) 24
Low voltage for initialization VCC(low) 0.7 V VCC (low voltage for initialization to occur) 24
Power-up time tPU 300 µs VCC(min) to Read operation 24
VCC low time tPD 10 µs VCC(low) time 24
Input low voltage VIL -0.5 V Operating temperature range -40 °C to +85 °C 25
Output low voltage VOL 0.2 V IOL = 0.1 mA 25
Input leakage current ILI -2 2 µA VCC = VCC Max, VIN = VIH or VSS, CS# = VIH 25
Output leakage current ILO -2 2 µA VCC = VCC Max, VIN = VIH or VSS, CS# = VIH 25
Active power supply current (READ) ICC1 10 18 mA Serial SDR@54 MHz 25
Active power supply current (READ) ICC1 25 30 mA Serial SDR@133 MHz 25
Active power supply current (READ) ICC1 60 65 mA Quad SDR@133 MHz 25
Active power supply current (READ) ICC1 70 90 mA Quad DDR@80 MHz 25
Active power supply current (Page Program) ICC2 60 100 mA CS# = VCC 25
Active power supply current (WRR or WRAR) ICC3 60 100 mA CS# = VCC 25
Active power supply current (SE) ICC4 60 100 mA CS# = VCC 25
Active power supply current (BE) ICC5 60 100 mA CS# = VCC 25
Standby current ISB 25 100 µA IO3 / RESET#, CS# = VCC; SI, SCK = VCC or VSS 25
Deep power-down current IDPD 8 50 µA IO3 / RESET#, CS# = VCC; SI, SCK = VCC or VSS 25
Power on reset current IPOR 80 mA IO3 / RESET#, CS# = VCC; SI, SCK = VCC or VSS 25
Reset setup time tRS 50 ns Prior reset end and RESET# high before RESET# low 31
Reset pulse hold tRPH 35 µs RESET# low to CS# low 31
RESET# pulse width tRP 200 ns RESET# pulse width 31
Reset hold time tRH 50 ns RESET# high before CS# low 31
SCK clock frequency (READ, 4READ) FSCK,R 50 MHz READ and 4READ instructions 32
SCK clock frequency (dual and quad commands) FSCK,C 133 MHz QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR 32
CS# high time (read instructions) tCS 10 ns CS# High Time (Read Instructions) 32
CS# high time (read, reset and quad enabled) tCS 20 ns Read Instructions when Reset feature and Quad mode are both enabled 32
CS# high time (program/erase) tCS 50 ns Program / Erase Instructions 32
CS# active setup time tCSS 2 ns Relative to SCK 32
CS# active hold time tCSH 3 ns Relative to SCK 32
Data in setup time tSU 2 ns 32
Data in hold time tHD 3 ns 32
Clock low to output valid tV 8 ns Full VCC range and CL = 30 pF 32
Clock low to output valid tV 6 ns Full VCC range and CL = 15 pF 32
Output hold time tHO 1 ns 32
Output disable time tDIS 8 ns Output Hi-Z defined where data no longer driven 32
Output disable time (reset and quad enabled) tDIS 20 ns When Reset feature and Quad mode are both enabled 32
WP# setup time tWPS 20 ns 32
WP# hold time tWPH 100 ns 32
CS# high to power-down mode tDPD 3 µs 32
CS# high to standby mode without electronic signature read tRES 30 µs Without Electronic Signature Read 32
Clock rise time (slew rate) tCRT 0.1 V/ns Clock rise time (slew rate) 32
Clock fall time (slew rate) tCFT 0.1 V/ns Clock fall time (slew rate) 32
Thermal resistance, junction to ambient theta JA 38 °C/W Package SO3016 (SOIC 16) 23

CAD (KiCad official)

  • Symbol: S25FS512SAGMFI011
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: s25fs512sagmfi011-etched.step / s25fs512sagmfi011-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fs512sagmfi011.step / s25fs512sagmfi011.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Cypress Semicon datasheet, copy hosted by LCSC (140 pp, sha256 61d4950ab0ed31c7, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF