3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownS25FS512SAGMFI011
Cypress Semicon · NOR FLASH · SOIC-16-300mil
S25FS512SAGMFI011 from Cypress Semicon, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IO3/RESET# | bidirectional | Quad I/O data line IO3 or hardware RESET# input, with an internal pull-up so it may be left unconnected if quad mode and hardware reset are not in use. |
| 2 | VCC | power_in | Core and I/O supply voltage for the 1.8 V S25FS512S device. |
| 3 | RFU | unconnected | Reserved for future use. |
| 4 | NC | unconnected | Not connected internally. |
| 5 | DNU | unconnected | Do not use. |
| 6 | RFU | unconnected | Reserved for future use. |
| 7 | CS# | input | Chip select input that enables the device when driven low. |
| 8 | SO/IO1 | bidirectional | Serial data output in single mode or IO1 in dual and quad modes. |
| 9 | WP#/IO2 | bidirectional | Write protect input or IO2 in quad mode. |
| 10 | VSS | power_in | Supply and signal ground. |
| 11 | DNU | unconnected | Do not use. |
| 12 | NC | unconnected | Not connected internally. |
| 13 | DNU | unconnected | Do not use. |
| 14 | RFU | unconnected | Reserved for future use. |
| 15 | SI/IO0 | bidirectional | Serial data input in single mode or IO0 in dual and quad modes. |
| 16 | SCK | input | Serial clock input. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-16-300mil |
| Category | Memory |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC | VCC | 1.7 | 2 | V | Operating range, Industrial (I) grade | 23 | |
| Ambient temperature, Industrial (I) | TA | -40 | 85 | °C | Industrial (I) grade, ordering code MFI, -40 °C to +85 °C | 23 | |
| Supply voltage with respect to ground | VCC | -0.5 | 2.5 | V | 23 | ||
| Output short circuit current | 100 | mA | No more than one output shorted to ground at a time; duration not greater than one second (note 10) | 23 | |||
| Storage temperature | TSTORE | -65 | 150 | °C | Plastic packages | 23 | |
| Ambient temperature with power applied | TA | -65 | 150 | °C | Power applied | 23 | |
| VCC current (latchup) | -100 | 100 | mA | Latchup specification | 23 | ||
| Minimum operation voltage | VCC(min) | 1.7 | V | VCC(minimum operation voltage) | 24 | ||
| Cut-off voltage for re-initialization | VCC(cut-off) | 1.5 | V | VCC (Cut-off where re-initialization is needed) | 24 | ||
| Low voltage for initialization | VCC(low) | 0.7 | V | VCC (low voltage for initialization to occur) | 24 | ||
| Power-up time | tPU | 300 | µs | VCC(min) to Read operation | 24 | ||
| VCC low time | tPD | 10 | µs | VCC(low) time | 24 | ||
| Input low voltage | VIL | -0.5 | V | Operating temperature range -40 °C to +85 °C | 25 | ||
| Output low voltage | VOL | 0.2 | V | IOL = 0.1 mA | 25 | ||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VSS, CS# = VIH | 25 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VSS, CS# = VIH | 25 | |
| Active power supply current (READ) | ICC1 | 10 | 18 | mA | Serial SDR@54 MHz | 25 | |
| Active power supply current (READ) | ICC1 | 25 | 30 | mA | Serial SDR@133 MHz | 25 | |
| Active power supply current (READ) | ICC1 | 60 | 65 | mA | Quad SDR@133 MHz | 25 | |
| Active power supply current (READ) | ICC1 | 70 | 90 | mA | Quad DDR@80 MHz | 25 | |
| Active power supply current (Page Program) | ICC2 | 60 | 100 | mA | CS# = VCC | 25 | |
| Active power supply current (WRR or WRAR) | ICC3 | 60 | 100 | mA | CS# = VCC | 25 | |
| Active power supply current (SE) | ICC4 | 60 | 100 | mA | CS# = VCC | 25 | |
| Active power supply current (BE) | ICC5 | 60 | 100 | mA | CS# = VCC | 25 | |
| Standby current | ISB | 25 | 100 | µA | IO3 / RESET#, CS# = VCC; SI, SCK = VCC or VSS | 25 | |
| Deep power-down current | IDPD | 8 | 50 | µA | IO3 / RESET#, CS# = VCC; SI, SCK = VCC or VSS | 25 | |
| Power on reset current | IPOR | 80 | mA | IO3 / RESET#, CS# = VCC; SI, SCK = VCC or VSS | 25 | ||
| Reset setup time | tRS | 50 | ns | Prior reset end and RESET# high before RESET# low | 31 | ||
| Reset pulse hold | tRPH | 35 | µs | RESET# low to CS# low | 31 | ||
| RESET# pulse width | tRP | 200 | ns | RESET# pulse width | 31 | ||
| Reset hold time | tRH | 50 | ns | RESET# high before CS# low | 31 | ||
| SCK clock frequency (READ, 4READ) | FSCK,R | 50 | MHz | READ and 4READ instructions | 32 | ||
| SCK clock frequency (dual and quad commands) | FSCK,C | 133 | MHz | QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 32 | ||
| CS# high time (read instructions) | tCS | 10 | ns | CS# High Time (Read Instructions) | 32 | ||
| CS# high time (read, reset and quad enabled) | tCS | 20 | ns | Read Instructions when Reset feature and Quad mode are both enabled | 32 | ||
| CS# high time (program/erase) | tCS | 50 | ns | Program / Erase Instructions | 32 | ||
| CS# active setup time | tCSS | 2 | ns | Relative to SCK | 32 | ||
| CS# active hold time | tCSH | 3 | ns | Relative to SCK | 32 | ||
| Data in setup time | tSU | 2 | ns | 32 | |||
| Data in hold time | tHD | 3 | ns | 32 | |||
| Clock low to output valid | tV | 8 | ns | Full VCC range and CL = 30 pF | 32 | ||
| Clock low to output valid | tV | 6 | ns | Full VCC range and CL = 15 pF | 32 | ||
| Output hold time | tHO | 1 | ns | 32 | |||
| Output disable time | tDIS | 8 | ns | Output Hi-Z defined where data no longer driven | 32 | ||
| Output disable time (reset and quad enabled) | tDIS | 20 | ns | When Reset feature and Quad mode are both enabled | 32 | ||
| WP# setup time | tWPS | 20 | ns | 32 | |||
| WP# hold time | tWPH | 100 | ns | 32 | |||
| CS# high to power-down mode | tDPD | 3 | µs | 32 | |||
| CS# high to standby mode without electronic signature read | tRES | 30 | µs | Without Electronic Signature Read | 32 | ||
| Clock rise time (slew rate) | tCRT | 0.1 | V/ns | Clock rise time (slew rate) | 32 | ||
| Clock fall time (slew rate) | tCFT | 0.1 | V/ns | Clock fall time (slew rate) | 32 | ||
| Thermal resistance, junction to ambient | theta JA | 38 | °C/W | Package SO3016 (SOIC 16) | 23 |
CAD (KiCad official)
- Symbol:
S25FS512SAGMFI011 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
s25fs512sagmfi011-etched.step/s25fs512sagmfi011-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fs512sagmfi011.step/s25fs512sagmfi011.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet, copy hosted by LCSC (140 pp, sha256
61d4950ab0ed31c7, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).