main
Ray
Publish 0.1.0
9407433
S25FL512SAGMFIG10
Cypress Semicon · NOR FLASH · SOIC-16-300mil
S25FL512SAGMFIG10 from Cypress Semicon, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HOLD#/IO3 | bidirectional | HOLD# input pauses a command when Quad mode is off (CR[1]=0) and acts as IO3 when Quad mode is enabled. |
| 2 | VCC | power_in | Core voltage supply for all internal logic, 2.7V to 3.6V. |
| 3 | RESET# | input | Hardware reset input, present on this model (ordering code G, SO footprint with RESET#); driving it low for tRP starts the hardware reset process. |
| 4 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 5 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 6 | RFU | unconnected | Reserved for Future Use: no internal signal is connected, and the datasheet recommends not routing PCB signals through it. |
| 7 | CS# | input | Chip Select input; a low level starts a command and a high level puts the SPI interface in standby. |
| 8 | SO/IO1 | bidirectional | Serial Output in single mode and IO1 in dual and quad modes. |
| 9 | WP#/IO2 | bidirectional | Write Protect input (relevant only during WRR instruction cycles) when Quad mode is off, and IO2 when Quad mode is enabled. |
| 10 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 11 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 12 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 13 | NC | unconnected | Not Connected: no internal signal is connected, and any signal on it must not exceed VIO. |
| 14 | VIO/RFU | unconnected | On this model VIO is tied to VCC inside the package (no separate VIO support), so this connector is left unconnected as RFU. |
| 15 | SI/IO0 | bidirectional | Serial Input in single mode and IO0 in dual and quad modes. |
| 16 | SCK | input | Serial Clock input for SPI modes 0 and 3. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-16-300mil |
| Category | Memory |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Core supply voltage | VCC | 2.7 | 3.6 | V | Operating range; VIO = VCC | 24 | |
| I/O supply voltage | VIO | 1.65 | V | Upper limit printed as VCC +200 mV | 24 | ||
| Ambient temperature (Industrial grade I) | TA | -40 | 85 | °C | Industrial (I) grade, suffix I | 24 | |
| Core supply voltage absolute maximum | VCC | -0.5 | 4 | V | 24 | ||
| VIO absolute maximum | VIO | -0.5 | 4 | V | Note 1: VIO must always be less than or equal to VCC + 200 mV | 24 | |
| Input voltage with respect to ground | -0.5 | V | Printed maximum +(VIO + 0.5V); Note 2 | 24 | |||
| Output short circuit current | 100 | mA | Note 3: no more than one output shorted at a time, duration not greater than one second | 24 | |||
| Storage temperature, plastic packages | TSTORE | -65 | 150 | °C | Plastic packages | 24 | |
| Ambient temperature with power applied | TA | -65 | 125 | °C | With power applied | 24 | |
| Power-up/power-down time delay | tPD | 10 | µs | VCC (low) time | 26 | ||
| Power-up time | tPU | 300 | µs | VCC (min) to Read operation | 26 | ||
| Core supply voltage minimum operation | VCC (min) | 2.7 | V | VCC (minimum operation voltage) | 26 | ||
| Core supply cut-off voltage | VCC (cut-off) | 2.4 | V | Cut-off where re-initialization is needed | 26 | ||
| Core supply low voltage for initialization | VCC (low) | 1.6 | V | Low voltage for initialization to occur | 26 | ||
| Low voltage for initialization at embedded operation | VCC (low) | 2.3 | V | Low voltage for initialization to occur at embedded | 26 | ||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 27 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 27 | |
| Active power supply current (READ), serial SDR at 133 MHz | ICC1 | 33 | mA | Serial SDR @133 MHz, outputs unconnected during read data return, Industrial temperature range | 27 | ||
| Active power supply current (READ), quad SDR at 104 MHz | ICC1 | 61 | mA | Quad SDR @104 MHz, outputs unconnected during read data return | 27 | ||
| Active power supply current (Page Program) | ICC2 | 100 | mA | CS# = VIO | 27 | ||
| Active power supply current (WRR) | ICC3 | 100 | mA | CS# = VIO | 27 | ||
| Active power supply current (SE) | ICC4 | 100 | mA | CS# = VIO | 27 | ||
| Active power supply current (BE) | ICC5 | 100 | mA | CS# = VIO | 27 | ||
| Standby current (Industrial) | ISB | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial temp | 27 | |
| Input capacitance (SCK, CS#, RESET#) | CIN | 8 | pF | 1 MHz, TA = 25°C | 29 | ||
| Output capacitance (all I/O) | COUT | 8 | pF | 1 MHz, TA = 25°C | 29 | ||
| Reset setup time | tRS | 50 | ns | Prior reset end and RESET# high before RESET# low | 30 | ||
| Reset pulse hold | tRPH | 35 | µs | RESET# low to CS# low | 30 | ||
| RESET# pulse width | tRP | 200 | ns | 30 | |||
| Reset hold | tRH | 50 | ns | RESET# high before CS# low | 30 | ||
| SCK clock frequency for READ and 4READ | FSCK, R | 50 | MHz | VIO = VCC 2.7V to 3.6V | 31 | ||
| SCK clock frequency for single commands | FSCK, C | 133 | MHz | Single commands as shown in Table 39 (note 4) | 31 | ||
| SCK clock frequency for dual and quad commands | FSCK, C | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 31 | ||
| SCK clock frequency for QPP and 4QPP | FSCK, QPP | 80 | MHz | QPP, 4QPP commands | 31 | ||
| CS# high time (read instructions) | tCS | 10 | ns | Read instructions | 31 | ||
| CS# high time (program/erase) | tCS | 50 | ns | Program/Erase | 31 | ||
| CS# active setup time | tCSS | 3 | ns | Relative to SCK | 31 | ||
| CS# active hold time | tCSH | 3 | 3000 | ns | Relative to SCK; max applies only during Program/Erase Suspend/Resume | 31 | |
| Data in setup time | tSU | 1.5 | ns | 31 | |||
| Data in hold time | tHD | 2 | ns | 31 | |||
| Clock low to output valid | tV | 8 | ns | Full VCC range 2.7-3.6V, CL = 30 pF | 31 | ||
| Clock low to output valid | tV | 7.65 | ns | Regulated VCC range 3.0-3.6V, CL = 30 pF | 31 | ||
| Clock low to output valid | tV | 6.5 | ns | Regulated VCC range 3.0-3.6V, CL = 15 pF | 31 | ||
| Output hold time | tHO | 2 | ns | 31 | |||
| Output disable time | tDIS | 0 | 8 | ns | 31 | ||
| WP# setup time | tWPS | 20 | ns | Only applicable when SRWD is set to 1 (WRR) | 31 | ||
| WP# hold time | tWPH | 100 | ns | Only applicable when SRWD is set to 1 (WRR) | 31 | ||
| HOLD# active setup time | tHLCH | 3 | ns | Relative to SCK | 31 | ||
| HOLD# active hold time | tCHHH | 3 | ns | Relative to SCK | 31 | ||
| HOLD# non-active setup time | tHHCH | 3 | ns | Relative to SCK | 31 | ||
| HOLD# non-active hold time | tCHHL | 3 | ns | Relative to SCK | 31 | ||
| HOLD# enable to output invalid | tHZ | 8 | ns | 31 | |||
| HOLD# disable to output valid | tLZ | 8 | ns | 31 | |||
| Thermal resistance, junction to ambient | θJA | 38 | °C/W | Junction to ambient, SO16 package | 24 |
CAD (KiCad official)
- Symbol:
S25FL512SAGMFIG10 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
s25fl512sagmfig10-etched.step/s25fl512sagmfig10-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl512sagmfig10.step/s25fl512sagmfig10.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet, copy hosted by LCSC (136 pp, sha256
790f303cd0149e3f, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# S25FL512SAGMFIG10
**Cypress Semicon** · NOR FLASH · SOIC-16-300mil
S25FL512SAGMFIG10 from Cypress Semicon, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HOLD#/IO3 | bidirectional | HOLD# input pauses a command when Quad mode is off (CR[1]=0) and acts as IO3 when Quad mode is enabled. |
| 2 | VCC | power_in | Core voltage supply for all internal logic, 2.7V to 3.6V. |
| 3 | RESET# | input | Hardware reset input, present on this model (ordering code G, SO footprint with RESET#); driving it low for tRP starts the hardware reset process. |
| 4 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 5 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 6 | RFU | unconnected | Reserved for Future Use: no internal signal is connected, and the datasheet recommends not routing PCB signals through it. |
| 7 | CS# | input | Chip Select input; a low level starts a command and a high level puts the SPI interface in standby. |
| 8 | SO/IO1 | bidirectional | Serial Output in single mode and IO1 in dual and quad modes. |
| 9 | WP#/IO2 | bidirectional | Write Protect input (relevant only during WRR instruction cycles) when Quad mode is off, and IO2 when Quad mode is enabled. |
| 10 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 11 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 12 | DNU | unconnected | Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected. |
| 13 | NC | unconnected | Not Connected: no internal signal is connected, and any signal on it must not exceed VIO. |
| 14 | VIO/RFU | unconnected | On this model VIO is tied to VCC inside the package (no separate VIO support), so this connector is left unconnected as RFU. |
| 15 | SI/IO0 | bidirectional | Serial Input in single mode and IO0 in dual and quad modes. |
| 16 | SCK | input | Serial Clock input for SPI modes 0 and 3. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-16-300mil |
| Category | Memory |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Core supply voltage | VCC | 2.7 | | 3.6 | V | Operating range; VIO = VCC | 24 |
| I/O supply voltage | VIO | 1.65 | | | V | Upper limit printed as VCC +200 mV | 24 |
| Ambient temperature (Industrial grade I) | TA | -40 | | 85 | °C | Industrial (I) grade, suffix I | 24 |
| Core supply voltage absolute maximum | VCC | -0.5 | | 4 | V | | 24 |
| VIO absolute maximum | VIO | -0.5 | | 4 | V | Note 1: VIO must always be less than or equal to VCC + 200 mV | 24 |
| Input voltage with respect to ground | | -0.5 | | | V | Printed maximum +(VIO + 0.5V); Note 2 | 24 |
| Output short circuit current | | | | 100 | mA | Note 3: no more than one output shorted at a time, duration not greater than one second | 24 |
| Storage temperature, plastic packages | TSTORE | -65 | | 150 | °C | Plastic packages | 24 |
| Ambient temperature with power applied | TA | -65 | | 125 | °C | With power applied | 24 |
| Power-up/power-down time delay | tPD | 10 | | | µs | VCC (low) time | 26 |
| Power-up time | tPU | | | 300 | µs | VCC (min) to Read operation | 26 |
| Core supply voltage minimum operation | VCC (min) | 2.7 | | | V | VCC (minimum operation voltage) | 26 |
| Core supply cut-off voltage | VCC (cut-off) | 2.4 | | | V | Cut-off where re-initialization is needed | 26 |
| Core supply low voltage for initialization | VCC (low) | 1.6 | | | V | Low voltage for initialization to occur | 26 |
| Low voltage for initialization at embedded operation | VCC (low) | 2.3 | | | V | Low voltage for initialization to occur at embedded | 26 |
| Input leakage current | ILI | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 27 |
| Output leakage current | ILO | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 27 |
| Active power supply current (READ), serial SDR at 133 MHz | ICC1 | | | 33 | mA | Serial SDR @133 MHz, outputs unconnected during read data return, Industrial temperature range | 27 |
| Active power supply current (READ), quad SDR at 104 MHz | ICC1 | | | 61 | mA | Quad SDR @104 MHz, outputs unconnected during read data return | 27 |
| Active power supply current (Page Program) | ICC2 | | | 100 | mA | CS# = VIO | 27 |
| Active power supply current (WRR) | ICC3 | | | 100 | mA | CS# = VIO | 27 |
| Active power supply current (SE) | ICC4 | | | 100 | mA | CS# = VIO | 27 |
| Active power supply current (BE) | ICC5 | | | 100 | mA | CS# = VIO | 27 |
| Standby current (Industrial) | ISB | | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial temp | 27 |
| Input capacitance (SCK, CS#, RESET#) | CIN | | | 8 | pF | 1 MHz, TA = 25°C | 29 |
| Output capacitance (all I/O) | COUT | | | 8 | pF | 1 MHz, TA = 25°C | 29 |
| Reset setup time | tRS | 50 | | | ns | Prior reset end and RESET# high before RESET# low | 30 |
| Reset pulse hold | tRPH | 35 | | | µs | RESET# low to CS# low | 30 |
| RESET# pulse width | tRP | 200 | | | ns | | 30 |
| Reset hold | tRH | 50 | | | ns | RESET# high before CS# low | 30 |
| SCK clock frequency for READ and 4READ | FSCK, R | | | 50 | MHz | VIO = VCC 2.7V to 3.6V | 31 |
| SCK clock frequency for single commands | FSCK, C | | | 133 | MHz | Single commands as shown in Table 39 (note 4) | 31 |
| SCK clock frequency for dual and quad commands | FSCK, C | | | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 31 |
| SCK clock frequency for QPP and 4QPP | FSCK, QPP | | | 80 | MHz | QPP, 4QPP commands | 31 |
| CS# high time (read instructions) | tCS | 10 | | | ns | Read instructions | 31 |
| CS# high time (program/erase) | tCS | 50 | | | ns | Program/Erase | 31 |
| CS# active setup time | tCSS | 3 | | | ns | Relative to SCK | 31 |
| CS# active hold time | tCSH | 3 | | 3000 | ns | Relative to SCK; max applies only during Program/Erase Suspend/Resume | 31 |
| Data in setup time | tSU | 1.5 | | | ns | | 31 |
| Data in hold time | tHD | 2 | | | ns | | 31 |
| Clock low to output valid | tV | | | 8 | ns | Full VCC range 2.7-3.6V, CL = 30 pF | 31 |
| Clock low to output valid | tV | | | 7.65 | ns | Regulated VCC range 3.0-3.6V, CL = 30 pF | 31 |
| Clock low to output valid | tV | | | 6.5 | ns | Regulated VCC range 3.0-3.6V, CL = 15 pF | 31 |
| Output hold time | tHO | 2 | | | ns | | 31 |
| Output disable time | tDIS | 0 | | 8 | ns | | 31 |
| WP# setup time | tWPS | 20 | | | ns | Only applicable when SRWD is set to 1 (WRR) | 31 |
| WP# hold time | tWPH | 100 | | | ns | Only applicable when SRWD is set to 1 (WRR) | 31 |
| HOLD# active setup time | tHLCH | 3 | | | ns | Relative to SCK | 31 |
| HOLD# active hold time | tCHHH | 3 | | | ns | Relative to SCK | 31 |
| HOLD# non-active setup time | tHHCH | 3 | | | ns | Relative to SCK | 31 |
| HOLD# non-active hold time | tCHHL | 3 | | | ns | Relative to SCK | 31 |
| HOLD# enable to output invalid | tHZ | | | 8 | ns | | 31 |
| HOLD# disable to output valid | tLZ | | | 8 | ns | | 31 |
| Thermal resistance, junction to ambient | θJA | | 38 | | °C/W | Junction to ambient, SO16 package | 24 |
## CAD (KiCad official)
- Symbol: `S25FL512SAGMFIG10`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files: `s25fl512sagmfig10-etched.step` / `s25fl512sagmfig10-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `s25fl512sagmfig10.step` / `s25fl512sagmfig10.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Cypress Semicon datasheet, copy hosted by LCSC](docs/s25fl512sagmfig10-datasheet.pdf) (136 pp, sha256 `790f303cd0149e3f`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/s25fl512sagmfig10-datasheet.pdf)