main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers s25fl512sagmfig10: viewers · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
s25fl512sagmfig10-etched.glb s25fl512sagmfig10: factory component page (tier=lcsc) · Ray
s25fl512sagmfig10-etched.step s25fl512sagmfig10: factory component page (tier=lcsc) · Ray
s25fl512sagmfig10-hero.glb s25fl512sagmfig10: hero GLB from the etched model (keeps the MPN mark) · Ray
s25fl512sagmfig10-hero.overlay.json s25fl512sagmfig10: hero GLB from the etched model (keeps the MPN mark) · Ray
s25fl512sagmfig10.glb Publish 0.1.0 · Ray
s25fl512sagmfig10.kicad_mod Publish 0.1.0 · Ray
s25fl512sagmfig10.kicad_sym Publish 0.1.0 · Ray
s25fl512sagmfig10.lbr Publish 0.1.0 · Ray
s25fl512sagmfig10.step Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 16 pins · Ray

S25FL512SAGMFIG10

Cypress Semicon · NOR FLASH · SOIC-16-300mil

S25FL512SAGMFIG10 from Cypress Semicon, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 HOLD#/IO3 bidirectional HOLD# input pauses a command when Quad mode is off (CR[1]=0) and acts as IO3 when Quad mode is enabled.
2 VCC power_in Core voltage supply for all internal logic, 2.7V to 3.6V.
3 RESET# input Hardware reset input, present on this model (ordering code G, SO footprint with RESET#); driving it low for tRP starts the hardware reset process.
4 DNU unconnected Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected.
5 DNU unconnected Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected.
6 RFU unconnected Reserved for Future Use: no internal signal is connected, and the datasheet recommends not routing PCB signals through it.
7 CS# input Chip Select input; a low level starts a command and a high level puts the SPI interface in standby.
8 SO/IO1 bidirectional Serial Output in single mode and IO1 in dual and quad modes.
9 WP#/IO2 bidirectional Write Protect input (relevant only during WRR instruction cycles) when Quad mode is off, and IO2 when Quad mode is enabled.
10 VSS power_in Common ground reference for the device core, input receivers and output drivers.
11 DNU unconnected Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected.
12 DNU unconnected Do Not Use: internal pull-down, may be left unconnected or tied to VSS, and no host signal may be connected.
13 NC unconnected Not Connected: no internal signal is connected, and any signal on it must not exceed VIO.
14 VIO/RFU unconnected On this model VIO is tied to VCC inside the package (no separate VIO support), so this connector is left unconnected as RFU.
15 SI/IO0 bidirectional Serial Input in single mode and IO0 in dual and quad modes.
16 SCK input Serial Clock input for SPI modes 0 and 3.

Key specifications

Parameter Value
Manufacturer Cypress Semicon
Package SOIC-16-300mil
Category Memory
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Core supply voltage VCC 2.7 3.6 V Operating range; VIO = VCC 24
I/O supply voltage VIO 1.65 V Upper limit printed as VCC +200 mV 24
Ambient temperature (Industrial grade I) TA -40 85 °C Industrial (I) grade, suffix I 24
Core supply voltage absolute maximum VCC -0.5 4 V 24
VIO absolute maximum VIO -0.5 4 V Note 1: VIO must always be less than or equal to VCC + 200 mV 24
Input voltage with respect to ground -0.5 V Printed maximum +(VIO + 0.5V); Note 2 24
Output short circuit current 100 mA Note 3: no more than one output shorted at a time, duration not greater than one second 24
Storage temperature, plastic packages TSTORE -65 150 °C Plastic packages 24
Ambient temperature with power applied TA -65 125 °C With power applied 24
Power-up/power-down time delay tPD 10 µs VCC (low) time 26
Power-up time tPU 300 µs VCC (min) to Read operation 26
Core supply voltage minimum operation VCC (min) 2.7 V VCC (minimum operation voltage) 26
Core supply cut-off voltage VCC (cut-off) 2.4 V Cut-off where re-initialization is needed 26
Core supply low voltage for initialization VCC (low) 1.6 V Low voltage for initialization to occur 26
Low voltage for initialization at embedded operation VCC (low) 2.3 V Low voltage for initialization to occur at embedded 26
Input leakage current ILI -2 2 µA VCC = VCC Max, VIN = VIH or VIL 27
Output leakage current ILO -2 2 µA VCC = VCC Max, VIN = VIH or VIL 27
Active power supply current (READ), serial SDR at 133 MHz ICC1 33 mA Serial SDR @133 MHz, outputs unconnected during read data return, Industrial temperature range 27
Active power supply current (READ), quad SDR at 104 MHz ICC1 61 mA Quad SDR @104 MHz, outputs unconnected during read data return 27
Active power supply current (Page Program) ICC2 100 mA CS# = VIO 27
Active power supply current (WRR) ICC3 100 mA CS# = VIO 27
Active power supply current (SE) ICC4 100 mA CS# = VIO 27
Active power supply current (BE) ICC5 100 mA CS# = VIO 27
Standby current (Industrial) ISB 70 100 µA RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial temp 27
Input capacitance (SCK, CS#, RESET#) CIN 8 pF 1 MHz, TA = 25°C 29
Output capacitance (all I/O) COUT 8 pF 1 MHz, TA = 25°C 29
Reset setup time tRS 50 ns Prior reset end and RESET# high before RESET# low 30
Reset pulse hold tRPH 35 µs RESET# low to CS# low 30
RESET# pulse width tRP 200 ns 30
Reset hold tRH 50 ns RESET# high before CS# low 30
SCK clock frequency for READ and 4READ FSCK, R 50 MHz VIO = VCC 2.7V to 3.6V 31
SCK clock frequency for single commands FSCK, C 133 MHz Single commands as shown in Table 39 (note 4) 31
SCK clock frequency for dual and quad commands FSCK, C 104 MHz DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR 31
SCK clock frequency for QPP and 4QPP FSCK, QPP 80 MHz QPP, 4QPP commands 31
CS# high time (read instructions) tCS 10 ns Read instructions 31
CS# high time (program/erase) tCS 50 ns Program/Erase 31
CS# active setup time tCSS 3 ns Relative to SCK 31
CS# active hold time tCSH 3 3000 ns Relative to SCK; max applies only during Program/Erase Suspend/Resume 31
Data in setup time tSU 1.5 ns 31
Data in hold time tHD 2 ns 31
Clock low to output valid tV 8 ns Full VCC range 2.7-3.6V, CL = 30 pF 31
Clock low to output valid tV 7.65 ns Regulated VCC range 3.0-3.6V, CL = 30 pF 31
Clock low to output valid tV 6.5 ns Regulated VCC range 3.0-3.6V, CL = 15 pF 31
Output hold time tHO 2 ns 31
Output disable time tDIS 0 8 ns 31
WP# setup time tWPS 20 ns Only applicable when SRWD is set to 1 (WRR) 31
WP# hold time tWPH 100 ns Only applicable when SRWD is set to 1 (WRR) 31
HOLD# active setup time tHLCH 3 ns Relative to SCK 31
HOLD# active hold time tCHHH 3 ns Relative to SCK 31
HOLD# non-active setup time tHHCH 3 ns Relative to SCK 31
HOLD# non-active hold time tCHHL 3 ns Relative to SCK 31
HOLD# enable to output invalid tHZ 8 ns 31
HOLD# disable to output valid tLZ 8 ns 31
Thermal resistance, junction to ambient θJA 38 °C/W Junction to ambient, SO16 package 24

CAD (KiCad official)

  • Symbol: S25FL512SAGMFIG10
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: s25fl512sagmfig10-etched.step / s25fl512sagmfig10-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fl512sagmfig10.step / s25fl512sagmfig10.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Cypress Semicon datasheet, copy hosted by LCSC (136 pp, sha256 790f303cd0149e3f, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF