main
Ray
Publish 0.1.0
1888d3e
S25FL256SAGNFI001
Cypress Semicon · NOR FLASH · WSON-8-EP(6x8)
S25FL256SAGNFI001 from Cypress Semicon, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input that frames each SPI command; driving CS# high ends a command sequence such as RDID. |
| 2 | SO/IO1 | bidirectional | Serial Output in single-bit mode and IO1 in dual/quad modes; high impedance when not driving data. |
| 3 | WP#/IO2 | bidirectional | Write Protect input that, when LOW with SRWD set, locks the Status Register, BP and configuration register bits; serves as IO2 in quad mode. |
| 4 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 5 | SI/IO0 | bidirectional | Serial Input for commands, addresses and data in single-bit mode, and IO0 in dual/quad modes. |
| 6 | SCK | input | Serial Clock input supporting SPI clock modes 0 and 3. |
| 7 | HOLD#/IO3 | bidirectional | Hold input in single/dual modes and IO3 in quad mode. |
| 8 | VCC | power_in | Core supply voltage for all internal logic, 2.7V to 3.6V; VIO and RESET# are tied to VCC internally in this package. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature, plastic packages | -65 | 150 | °C | 23 | |||
| Ambient temperature with power applied | -65 | 125 | °C | 23 | |||
| Core supply voltage | VCC | -0.5 | 4 | V | 23 | ||
| Output short circuit current | 100 | mA | No more than one output shorted at a time, not longer than one second | 23 | |||
| Supply voltage | VCC | 2.7 | 3.6 | V | 23 | ||
| Ambient temperature, Industrial | TA | -40 | 85 | °C | Industrial (I) | 23 | |
| Thermal resistance junction to ambient | Theta JA | 27 | °C/W | S25FL256, WNG008 | 23 | ||
| VCC minimum operation voltage | VCC (min) | 2.7 | V | 25 | |||
| VCC cut-off where re-initialization is needed | VCC (cut-off) | 2.4 | V | 25 | |||
| VCC low voltage for initialization to occur | VCC (low) | 1.6 | V | 2.3 V min at Embedded | 25 | ||
| VCC (min) to read operation | tPU | 300 | µs | 25 | |||
| VCC (low) time | tPD | 15 | µs | 25 | |||
| Input low voltage | VIL | -0.5 | V | max is 0.2 x VIO | 26 | ||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 | |
| Active read current, Serial SDR 50 MHz | ICC1 | 16 | mA | Outputs unconnected during read data return | 26 | ||
| Active read current, Serial SDR 133 MHz | ICC1 | 33 | mA | Outputs unconnected during read data return | 26 | ||
| Active read current, Quad SDR 80 MHz | ICC1 | 50 | mA | Outputs unconnected during read data return | 26 | ||
| Active read current, Quad SDR 104 MHz | ICC1 | 61 | mA | Outputs unconnected during read data return | 26 | ||
| Active read current, Quad DDR 66 MHz | ICC1 | 75 | mA | Outputs unconnected during read data return | 26 | ||
| Active read current, Quad DDR 80 MHz | ICC1 | 90 | mA | Outputs unconnected during read data return | 26 | ||
| Active current (Page Program) | ICC2 | 100 | mA | CS# = VIO | 26 | ||
| Active current (WRR) | ICC3 | 100 | mA | CS# = VIO | 26 | ||
| Active current (SE) | ICC4 | 100 | mA | CS# = VIO | 26 | ||
| Active current (BE) | ICC5 | 100 | mA | CS# = VIO | 26 | ||
| Standby current (Industrial) | ISB | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial Temp | 26 | |
| Input capacitance | CIN | 8 | pF | 1 MHz; applies to SCK, CS#, RESET# | 29 | ||
| Output capacitance | COUT | 8 | pF | 1 MHz; applies to all I/O | 29 | ||
| SCK clock frequency for READ and 4READ | FSCK, R | 0 | 50 | MHz | VIO = VCC 2.7V to 3.6V; min printed DC | 31 | |
| SCK clock frequency for single commands | FSCK, C | 0 | 133 | MHz | VIO = VCC 2.7V to 3.6V; min printed DC | 31 | |
| SCK clock frequency for dual and quad commands | FSCK, C | 0 | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR; min printed DC | 31 | |
| SCK clock frequency for QPP, 4QPP | FSCK, QPP | 0 | 80 | MHz | min printed DC | 31 | |
| Clock rise time (slew rate) | tCRT, tCLCH | 0.1 | V/ns | 31 | |||
| Clock fall time (slew rate) | tCFT, tCHCL | 0.1 | V/ns | 31 | |||
| CS# high time (read instructions) | tCS | 10 | ns | Read Instructions | 31 | ||
| CS# high time (program/erase) | tCS | 50 | ns | Program/Erase | 31 | ||
| CS# active setup time | tCSS | 3 | ns | relative to SCK | 31 | ||
| CS# active hold time | tCSH | 3 | ns | relative to SCK | 31 | ||
| Data in setup time | tSU | 1.5 | 3000 | ns | Max applies only during Program/Erase Suspend/Resume commands | 31 | |
| Data in hold time | tHD | 2 | ns | 31 | |||
| Clock low to output valid, full VCC range | tV | 8 | ns | Full VCC range (2.7 - 3.6V) and CL = 30 pF | 31 | ||
| Clock low to output valid, regulated VCC, 30 pF | tV | 7.65 | ns | Regulated VCC range (3.0 - 3.6V) and CL = 30 pF | 31 | ||
| Clock low to output valid, regulated VCC, 15 pF | tV | 6.5 | ns | Regulated VCC range (3.0 - 3.6V) and CL = 15 pF | 31 | ||
| Output hold time | tHO | 2 | ns | 31 | |||
| Output disable time | tDIS | 0 | 8 | ns | 31 | ||
| WP# setup time | tWPS | 20 | ns | Only for WRR instruction when SRWD is set to 1 | 31 | ||
| WP# hold time | tWPH | 100 | ns | Only for WRR instruction when SRWD is set to 1 | 31 | ||
| HOLD# active setup time | tHLCH | 3 | ns | relative to SCK | 31 | ||
| HOLD# active hold time | tCHHH | 3 | ns | relative to SCK | 31 | ||
| HOLD# non active setup time | tHHCH | 3 | ns | relative to SCK | 31 | ||
| HOLD# non active hold time | tCHHL | 3 | ns | relative to SCK | 31 | ||
| HOLD# enable to output invalid | tHZ | 8 | ns | 31 | |||
| HOLD# disable to output valid | tLZ | 8 | ns | 31 |
CAD (KiCad official)
- Symbol:
S25FL256SAGNFI001 - Footprint:
Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm - 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
s25fl256sagnfi001-etched.step/s25fl256sagnfi001-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl256sagnfi001.step/s25fl256sagnfi001.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet (146 pp, sha256
4cdc2a61d3d31251, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# S25FL256SAGNFI001
**Cypress Semicon** · NOR FLASH · WSON-8-EP(6x8)
S25FL256SAGNFI001 from Cypress Semicon, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input that frames each SPI command; driving CS# high ends a command sequence such as RDID. |
| 2 | SO/IO1 | bidirectional | Serial Output in single-bit mode and IO1 in dual/quad modes; high impedance when not driving data. |
| 3 | WP#/IO2 | bidirectional | Write Protect input that, when LOW with SRWD set, locks the Status Register, BP and configuration register bits; serves as IO2 in quad mode. |
| 4 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 5 | SI/IO0 | bidirectional | Serial Input for commands, addresses and data in single-bit mode, and IO0 in dual/quad modes. |
| 6 | SCK | input | Serial Clock input supporting SPI clock modes 0 and 3. |
| 7 | HOLD#/IO3 | bidirectional | Hold input in single/dual modes and IO3 in quad mode. |
| 8 | VCC | power_in | Core supply voltage for all internal logic, 2.7V to 3.6V; VIO and RESET# are tied to VCC internally in this package. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature, plastic packages | | -65 | | 150 | °C | | 23 |
| Ambient temperature with power applied | | -65 | | 125 | °C | | 23 |
| Core supply voltage | VCC | -0.5 | | 4 | V | | 23 |
| Output short circuit current | | | | 100 | mA | No more than one output shorted at a time, not longer than one second | 23 |
| Supply voltage | VCC | 2.7 | | 3.6 | V | | 23 |
| Ambient temperature, Industrial | TA | -40 | | 85 | °C | Industrial (I) | 23 |
| Thermal resistance junction to ambient | Theta JA | | 27 | | °C/W | S25FL256, WNG008 | 23 |
| VCC minimum operation voltage | VCC (min) | 2.7 | | | V | | 25 |
| VCC cut-off where re-initialization is needed | VCC (cut-off) | 2.4 | | | V | | 25 |
| VCC low voltage for initialization to occur | VCC (low) | 1.6 | | | V | 2.3 V min at Embedded | 25 |
| VCC (min) to read operation | tPU | | | 300 | µs | | 25 |
| VCC (low) time | tPD | 15 | | | µs | | 25 |
| Input low voltage | VIL | -0.5 | | | V | max is 0.2 x VIO | 26 |
| Input leakage current | ILI | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 |
| Output leakage current | ILO | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 |
| Active read current, Serial SDR 50 MHz | ICC1 | | | 16 | mA | Outputs unconnected during read data return | 26 |
| Active read current, Serial SDR 133 MHz | ICC1 | | | 33 | mA | Outputs unconnected during read data return | 26 |
| Active read current, Quad SDR 80 MHz | ICC1 | | | 50 | mA | Outputs unconnected during read data return | 26 |
| Active read current, Quad SDR 104 MHz | ICC1 | | | 61 | mA | Outputs unconnected during read data return | 26 |
| Active read current, Quad DDR 66 MHz | ICC1 | | | 75 | mA | Outputs unconnected during read data return | 26 |
| Active read current, Quad DDR 80 MHz | ICC1 | | | 90 | mA | Outputs unconnected during read data return | 26 |
| Active current (Page Program) | ICC2 | | | 100 | mA | CS# = VIO | 26 |
| Active current (WRR) | ICC3 | | | 100 | mA | CS# = VIO | 26 |
| Active current (SE) | ICC4 | | | 100 | mA | CS# = VIO | 26 |
| Active current (BE) | ICC5 | | | 100 | mA | CS# = VIO | 26 |
| Standby current (Industrial) | ISB | | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial Temp | 26 |
| Input capacitance | CIN | | | 8 | pF | 1 MHz; applies to SCK, CS#, RESET# | 29 |
| Output capacitance | COUT | | | 8 | pF | 1 MHz; applies to all I/O | 29 |
| SCK clock frequency for READ and 4READ | FSCK, R | 0 | | 50 | MHz | VIO = VCC 2.7V to 3.6V; min printed DC | 31 |
| SCK clock frequency for single commands | FSCK, C | 0 | | 133 | MHz | VIO = VCC 2.7V to 3.6V; min printed DC | 31 |
| SCK clock frequency for dual and quad commands | FSCK, C | 0 | | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR; min printed DC | 31 |
| SCK clock frequency for QPP, 4QPP | FSCK, QPP | 0 | | 80 | MHz | min printed DC | 31 |
| Clock rise time (slew rate) | tCRT, tCLCH | 0.1 | | | V/ns | | 31 |
| Clock fall time (slew rate) | tCFT, tCHCL | 0.1 | | | V/ns | | 31 |
| CS# high time (read instructions) | tCS | 10 | | | ns | Read Instructions | 31 |
| CS# high time (program/erase) | tCS | 50 | | | ns | Program/Erase | 31 |
| CS# active setup time | tCSS | 3 | | | ns | relative to SCK | 31 |
| CS# active hold time | tCSH | 3 | | | ns | relative to SCK | 31 |
| Data in setup time | tSU | 1.5 | | 3000 | ns | Max applies only during Program/Erase Suspend/Resume commands | 31 |
| Data in hold time | tHD | 2 | | | ns | | 31 |
| Clock low to output valid, full VCC range | tV | | | 8 | ns | Full VCC range (2.7 - 3.6V) and CL = 30 pF | 31 |
| Clock low to output valid, regulated VCC, 30 pF | tV | | | 7.65 | ns | Regulated VCC range (3.0 - 3.6V) and CL = 30 pF | 31 |
| Clock low to output valid, regulated VCC, 15 pF | tV | | | 6.5 | ns | Regulated VCC range (3.0 - 3.6V) and CL = 15 pF | 31 |
| Output hold time | tHO | 2 | | | ns | | 31 |
| Output disable time | tDIS | 0 | | 8 | ns | | 31 |
| WP# setup time | tWPS | 20 | | | ns | Only for WRR instruction when SRWD is set to 1 | 31 |
| WP# hold time | tWPH | 100 | | | ns | Only for WRR instruction when SRWD is set to 1 | 31 |
| HOLD# active setup time | tHLCH | 3 | | | ns | relative to SCK | 31 |
| HOLD# active hold time | tCHHH | 3 | | | ns | relative to SCK | 31 |
| HOLD# non active setup time | tHHCH | 3 | | | ns | relative to SCK | 31 |
| HOLD# non active hold time | tCHHL | 3 | | | ns | relative to SCK | 31 |
| HOLD# enable to output invalid | tHZ | | | 8 | ns | | 31 |
| HOLD# disable to output valid | tLZ | | | 8 | ns | | 31 |
## CAD (KiCad official)
- Symbol: `S25FL256SAGNFI001`
- Footprint: `Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm`
- 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `s25fl256sagnfi001-etched.step` / `s25fl256sagnfi001-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `s25fl256sagnfi001.step` / `s25fl256sagnfi001.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Cypress Semicon datasheet](docs/s25fl256sagnfi001-datasheet.pdf) (146 pp, sha256 `4cdc2a61d3d31251`, retrieved 2026-10-23, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/s25fl256sagnfi001-datasheet.pdf)